e4fb600739
Made multi extruder temps get read correctly. Signed the arduino inf and made our installer install it.
114 lines
No EOL
3.2 KiB
INI
114 lines
No EOL
3.2 KiB
INI
avoid_crossing_perimeters = 1
|
|
bottom_solid_layers = 3
|
|
bridge_acceleration = 500
|
|
bridge_flow_ratio = 0.9
|
|
bridge_speed = 25
|
|
brim_width = 1
|
|
complete_objects = 1
|
|
default_acceleration = 1200
|
|
external_perimeter_speed = 80%
|
|
external_perimeters_first = 0
|
|
extra_perimeters = 1
|
|
extruder_clearance_height = 35
|
|
extruder_clearance_radius = 40
|
|
extrusion_width = 0.7
|
|
fill_angle = 45
|
|
fill_density = 0.4
|
|
fill_pattern = honeycomb
|
|
first_layer_acceleration = 1200
|
|
first_layer_extrusion_width = 0
|
|
first_layer_height = 0.1
|
|
first_layer_speed = 70%
|
|
gap_fill_speed = 10
|
|
gcode_comments = 1
|
|
infill_acceleration = 200
|
|
infill_every_layers = 1
|
|
infill_extruder = 1
|
|
infill_extrusion_width = 0
|
|
infill_first = 1
|
|
infill_only_where_needed = 0
|
|
infill_speed = 60
|
|
layer_height = 0.2
|
|
min_skirt_length = 0
|
|
notes =
|
|
only_retract_when_crossing_perimeters = 1
|
|
ooze_prevention = 0
|
|
output_filename_format = [input_filename_base].gcode
|
|
overhangs =
|
|
perimeter_acceleration = 900
|
|
perimeter_extruder = 1
|
|
perimeter_extrusion_width = 0
|
|
perimeter_speed = 50
|
|
perimeters = 1
|
|
post_process =
|
|
raft_layers = 0
|
|
randomize_start = 1
|
|
resolution = 0
|
|
skirt_distance = 0.8
|
|
skirt_height = 2
|
|
skirts = 10
|
|
small_perimeter_speed = 30
|
|
solid_fill_pattern = concentric
|
|
solid_infill_below_area = 70
|
|
solid_infill_every_layers = 20
|
|
solid_infill_extrusion_width = 0
|
|
solid_infill_speed = 70%
|
|
spiral_vase = 0
|
|
standby_temperature_delta = -5
|
|
start_perimeters_at_concave_points = 0
|
|
start_perimeters_at_non_overhang = 0
|
|
support_material = 0
|
|
support_material_angle = 45
|
|
support_material_enforce_layers = 0
|
|
support_material_extruder = 1
|
|
support_material_extrusion_width = 0
|
|
support_material_interface_extruder = 1
|
|
support_material_interface_layers = 3
|
|
support_material_interface_spacing = 2.5
|
|
support_material_pattern = honeycomb
|
|
support_material_spacing = 2.5
|
|
support_material_speed = 60
|
|
support_material_threshold = 0
|
|
thin_walls = 1
|
|
threads = 2
|
|
top_infill_extrusion_width = 0.5
|
|
top_solid_infill_speed = 50
|
|
top_solid_layers = 3
|
|
travel_speed = 160
|
|
bed_temperature = 0
|
|
bridge_fan_speed = 100
|
|
cooling = 1
|
|
disable_fan_first_layers = 1
|
|
extrusion_multiplier = 1.0
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 60
|
|
filament_diameter = 2.92
|
|
first_layer_bed_temperature = 0
|
|
first_layer_temperature = 195
|
|
max_fan_speed = 100
|
|
min_fan_speed = 35
|
|
min_print_speed = 10
|
|
slowdown_below_layer_time = 30
|
|
temperature = 185
|
|
bed_size = 230,230
|
|
end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nG91 ; Set distance mode to relative value mode\nG1 E-5 F60 ; Retract E=- 5mm, rate F = 200mm/min \nG90 ; set distance mode to absolute value mode\nM84 ; disable motors
|
|
extruder_offset = 0x0
|
|
gcode_flavor = reprap
|
|
layer_gcode =
|
|
nozzle_diameter = 0.7
|
|
print_center = 120,130
|
|
retract_before_travel = 20
|
|
retract_layer_change = 0
|
|
retract_length = 7
|
|
retract_length_toolchange = 10
|
|
retract_lift = 0.1
|
|
retract_restart_extra = 0
|
|
retract_restart_extra_toolchange = 0
|
|
retract_speed = 35
|
|
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\nM109 S[first_layer_temperature] ; Set extruder temp S=180 degrees and wait\nG91 ; Set distance mode to relative value mode;\nG1 E25 F150 ; Extrude E= 25mm, rate F = 150mm/min \nG90 ; set distance mode to absolute value mode
|
|
toolchange_gcode =
|
|
use_firmware_retraction = 0
|
|
use_relative_e_distances = 0
|
|
vibration_limit = 0
|
|
wipe = 1
|
|
z_offset = -0.4 |