153 lines
4.3 KiB
INI
153 lines
4.3 KiB
INI
avoid_crossing_perimeters = 1
|
|
bed_shape = rectangular
|
|
bed_size = 215,215
|
|
bed_temperature = 100
|
|
bottom_clip_amount = 0
|
|
bridge_acceleration = 0
|
|
bridge_fan_speed = 100
|
|
bridge_flow_ratio = 1
|
|
bridge_speed = 20
|
|
brim_width = 0
|
|
build_height = 215
|
|
cancel_gcode = G28 X0
|
|
center_part_on_bed = 1
|
|
complete_objects = 0
|
|
cool_extruder_lift = 0
|
|
cooling = 1
|
|
create_raft = 0
|
|
default_acceleration = 0
|
|
disable_fan_first_layers = 1
|
|
end_gcode = M104 S0 ;extruder heater off\nM140 S0 ; bed heat off\nG91 ;relative positioning\nG1 E-2 F300 ;retract the filament a bit before lifting the nozzle\nG1 Z+1.0 E-2 X-20 F[travel_speed] ;move Z up a bit and retract filament \nG28 X0 y0 ;move X to min endstops, so the head is out of the way\nG1 F3200 Y200 ;move Y TO 200mm to REMOVE PARTS \nM84 ;steppers off\n
|
|
external_perimeter_speed = 40
|
|
external_perimeters_first = 0
|
|
extra_perimeters = 1
|
|
extruder_clearance_height = 20
|
|
extruder_clearance_radius = 20
|
|
extruder_count = 2
|
|
extruder_offset = 0x0,46x0
|
|
extruders_share_temperature = 0
|
|
extrusion_axis = E
|
|
extrusion_multiplier = 1
|
|
extrusion_width = 0
|
|
fan_always_on = 0
|
|
fan_below_layer_time = 60
|
|
filament_diameter = 1.75
|
|
fill_angle = 45
|
|
fill_density = 30%
|
|
fill_pattern = honeycomb
|
|
first_layer_acceleration = 0
|
|
first_layer_bed_temperature = 50
|
|
first_layer_height = 0.3
|
|
first_layer_speed = 35%
|
|
first_layer_temperature = 205
|
|
g0 = 0
|
|
gap_fill_speed = 20
|
|
gcode_arcs = 0
|
|
gcode_comments = 0
|
|
gcode_flavor = reprap
|
|
gcode_output_type = REPRAP
|
|
has_fan = 0
|
|
has_hardware_leveling = 1
|
|
has_heated_bed = 1
|
|
has_sd_card_reader = 1
|
|
show_reset_connection = 1
|
|
heat_extruder_before_homing = 0
|
|
include_firmware_updater = Simple Arduino
|
|
infill_acceleration = 0
|
|
infill_every_layers = 1
|
|
infill_extruder = 1
|
|
infill_extrusion_width = 0
|
|
infill_first = 0
|
|
infill_only_where_needed = 0
|
|
infill_overlap_perimeter = .06
|
|
infill_speed = 75
|
|
infill_type = TRIANGLES
|
|
layer_gcode =
|
|
layer_height = 0.2
|
|
max_fan_speed = 100
|
|
min_extrusion_before_retract = .1
|
|
min_fan_speed = 35
|
|
min_print_speed = 10
|
|
min_skirt_length = 5
|
|
notes =
|
|
nozzle_diameter = 0.35
|
|
only_retract_when_crossing_perimeters = 1
|
|
ooze_prevention = 0
|
|
output_filename_format = [input_filename_base].gcode
|
|
overhangs = 1
|
|
pause_gcode =
|
|
perimeter_acceleration = 0
|
|
perimeter_extruder = 1
|
|
perimeter_extrusion_width = 0
|
|
perimeter_speed = 40
|
|
perimeters = 3
|
|
post_process =
|
|
print_center = 155,105
|
|
raft_air_gap = .2
|
|
raft_extruder = 0
|
|
raft_extra_distance_around_part = 5
|
|
raft_fan_speed_percent = 100
|
|
raft_layers = 0
|
|
raft_print_speed = 100%
|
|
randomize_start = 0
|
|
repair_outlines_extensive_stitching = 0
|
|
repair_outlines_keep_open = 0
|
|
resolution = 0
|
|
resume_gcode =
|
|
retract_before_travel = 20
|
|
retract_layer_change = 1
|
|
retract_length = 1
|
|
retract_length_tool_change = 8
|
|
retract_lift = 0
|
|
retract_restart_extra = 0
|
|
retract_restart_extra_toolchange = 0
|
|
retract_speed = 30
|
|
skirt_distance = 2
|
|
skirt_height = 1
|
|
skirts = 1
|
|
slowdown_below_layer_time = 30
|
|
small_perimeter_speed = 30
|
|
solid_fill_pattern = rectilinear
|
|
solid_infill_below_area = 70
|
|
solid_infill_every_layers = 0
|
|
solid_infill_extrusion_width = 0
|
|
solid_infill_speed = 60
|
|
spiral_vase = 0
|
|
standby_temperature_delta = -5
|
|
start_gcode = G90 ;absolute positioning\nG28 X0 Y0 ;move X/Y to min endstops\nM84 ;steppers off\nG28 Z0 ;move Z to min endstops\nG1 F800 Z3 ;MOVE Z UP 3 to ensure clearance on first move\nG92 E0 ;zero the extruded length\nM117 [input_filename_base] ; what will be displayed
|
|
start_perimeters_at_concave_points = 0
|
|
start_perimeters_at_non_overhang = 0
|
|
support_material = 0
|
|
support_material_angle = 45
|
|
support_material_create_internal_support = 0
|
|
support_material_enforce_layers = 0
|
|
support_material_extruder = 1
|
|
support_material_extrusion_width = 0
|
|
support_material_infill_angle = 45
|
|
support_material_interface_extruder = 1
|
|
support_material_interface_layers = 3
|
|
support_material_interface_spacing = 0
|
|
support_material_pattern = honeycomb
|
|
support_material_spacing = 2.5
|
|
support_material_speed = 60
|
|
support_material_threshold = 0
|
|
support_material_xy_distance = 0.7
|
|
support_material_z_distance = 0.15
|
|
support_material_z_gap_layers = 1
|
|
support_type = LINES
|
|
temperature = 230
|
|
thin_walls = 1
|
|
threads = 2
|
|
toolchange_gcode =
|
|
top_infill_extrusion_width = 0
|
|
top_solid_infill_speed = 50
|
|
top_solid_layers = 1mm
|
|
travel_speed = 110
|
|
use_firmware_retraction = 0
|
|
use_relative_e_distances = 0
|
|
vibration_limit = 0
|
|
wipe = 0
|
|
wipe_shield_distance = 0
|
|
wipe_tower_size = 0
|
|
z_can_be_negative = 0
|
|
z_offset = 10
|