mattercontrol/StaticData/PrinterSettings/Me3D/Me2/config.ini

avoid_crossing_perimeters = 1
bed_shape = rectangular
bed_size = 200,200
bed_temperature = 0
bottom_clip_amount = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 20
brim_width = 0
build_height = 200
cancel_gcode = \n\n;Remove the ";" to activate any line\n\n;MAKE SURE YOU KNOW WHAT EACH LINE DOES BEFORE YOU CHANGE IT!!! The Me2 is 100% hackable and so has limited physical protection from mistakes in the g-code\n\nG91; Set to Relative position\n\nG1 Z3 E-3; move z axis up\n\nG28  ; home axis\n\n;G28 X0  ; home X axis\n\n;G28 Y0  ; home Y axis\n\n;G28 Z0  ; home Z axis\n\nG92 E0; zero the extruded length\n\nG1 F250 E-20; Retract filament from barrel\n\nG92 E0; zero the extruded length again\n\nG91; Set to Absolute position\n\nM104 S0 ; turn off temperature\n\nM140 S0 ; turn off heated bed\n\nM84     ; disable motors\n\nM117 Look...awesome! ; Put message on LCD screen
center_part_on_bed = 1
complete_objects = 0
cool_extruder_lift = 0
cooling = 1
create_raft = 0
raft_extra_distance_around_part = 5
raft_air_gap = .2
default_acceleration = 0
disable_fan_first_layers = 1
end_gcode = \n\n;Remove the ";" to activate any line\n\n;MAKE SURE YOU KNOW WHAT EACH LINE DOES BEFORE YOU CHANGE IT!!! The Me2 is 100% hackable and so has limited physical protection from mistakes in the g-code\n\nG91; Set to Relative position\n\nG1 Z3 E-3; move z axis up\n\nG28  ; home axis\n\n;G28 X0  ; home X axis\n\n;G28 Y0  ; home Y axis\n\n;G28 Z0  ; home Z axis\n\nG92 E0; zero the extruded length\n\nG1 F250 E-20; Retract filament from barrel\n\nG92 E0; zero the extruded length again\n\nG91; Set to Absolute position\n\nM104 S0 ; turn off temperature\n\nM140 S0 ; turn off heated bed\n\nM84     ; disable motors\n\nM117 Look...awesome! ; Put message on LCD screen
external_perimeter_speed = 50
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 40
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 45
fill_density = 0.2
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.2
first_layer_speed = 40
first_layer_temperature = 220
g0 = 0
gap_fill_speed = 20
gcode_arcs = 1
gcode_comments = 0
gcode_flavor = reprap
gcode_output_type = REPRAP
has_fan = 1
has_heated_bed = 0
has_sd_card_reader = 1
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap_perimeter = .06
infill_speed = 40
infill_type = GRID
layer_gcode = 
layer_height = 0.2
min_extrusion_before_retract = .1
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 30
notes = 
nozzle_diameter = 0.4
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
pause_gcode = 
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 40
perimeters = 2
post_process = 
print_center = 100,100
raft_layers = 0
randomize_start = 0
repair_outlines_extensive_stitching = 0
repair_outlines_keep_open = 0
repair_overlaps_reverse_orientation = 0
repair_overlaps_union_all_together = 0
resolution = 0
resume_gcode = 
retract_before_travel = 20
retract_layer_change = 1
retract_length = 3
retract_length_tool_change = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 30
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = ;Me3D - startup sequence - Me2 (G5,G6,G7) Build 30/08/14\n\n;Remove the ";" to activate any line\n\n;MAKE SURE YOU KNOW WHAT EACH LINE DOES BEFORE YOU CHANGE IT!!! The Me2 is 100% hackable and so has limited physical protection from errors in the g-code\n\n;Filament cost: {filament_cost}\n\n;M190 S{print_bed_temperature} ; // Uncomment to add your own bed temperature line\n\nM104 S{temperature} ; // Start heater and continue g-code\n\nG21 ; // set units to millimeters\n\n;M92 E106.707 ; // manually calibrate Extruder\n\n;M92 X80 ; // manually calibrate X //as measured - 20T=80 16T=100\n\n;M92 Y80 ; // manually calibrate Y // as measured - 20T=80 16T=100\n\n;M92 Z80 ; // manually calibrate Z  //as measured - 20T=80 16T=100\n\nM201 X3000 Y3000; // max accel print\n\nM202 X3000 Y3000; // max accel travel\n\n;M204 S3000; // default accel for normal moves\n\n;M205 X15; // max xyjerk mm/s\n\nM208 X200 Y200 Z200; // set build size\n\nG90 ; // use abs00olute coordinates\n\nM18; // Enable motors\n\nG28; // home axes\n\nG29; // perform auto levelling at three corners\n\nM82 ; // use absolute distances for extrusion\n\n;G1 Z25.0 F2000; OFFSET PART 1 //move to z offset, nominal Z7.5 mm already set in firmware, tweak to achieve good adhesion. Always check again before completing a full print this can severely damage the machine.\n\n;G92 Z0; OFFSET PART 2 // Set new Z position to zero.\n\nG1 Z15 F4000; // Raise Z axis clear\n\nG1 X0 F4000; // Move to X axis zero\n\nG92 E0; // zero the extruded length\n\nM109 S{temperature};  // Set print temperature and wait\n\nG1 F250 E40; // extrude feed stock to prime hotend barrel and purge\n\nG92 E0; // zero the extruded length again\n\n;G1 X36 Y43 ; // Position\n\n;G92 X0 Y0 Z0 ; // set z offset\n\nG0 Z0; // Lower z axis to bed height\n\nG0 X0 Y0; // Go to offset nozzle position\n\nM117 Awesome!!!  // Put message on LCD screen
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 0
support_material = 0
support_material_angle = 45
support_material_create_internal_support = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_pattern = honeycomb
support_material_spacing = 2.5
support_material_speed = 40
support_material_threshold = 0
support_material_xy_distance = 0.7
support_material_z_distance = 0.15
support_material_z_gap_layers = 1
support_type = GRID
temperature = 220
thin_walls = 1
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 4
travel_speed = 150
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
wipe_shield_distance = 0
z_offset = 0