mattercontrol/StaticData/PrinterSettings/Me3D/Me2/config.ini

avoid_crossing_perimeters = 0
bed_shape = rectangular
bed_size = 200,220
bed_temperature = 0
bottom_clip_amount = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 50
brim_width = 0
build_height = 180
cancel_gcode = G91; Set to Relative position\nG1 Z3 E-3; move z axis up\nG28; home axis\nG92 E0; zero the extruded length\nG1 F250 E-16; Retract filament from barrel\nG92 E0; zero the extruded length again\nG90; Set to Absolute position\nM104 S0; turn off temperature\nM140 S0; turn off heated bed\nM106 S0; Turn off fan\nM18;\nM117 Look...awesome!; Put message on LCD screen
center_part_on_bed = 1
complete_objects = 0
cool_extruder_lift = 0
cooling = 1
create_raft = 0
default_acceleration = 0
disable_fan_first_layers = 1
end_gcode = G91; Set to Relative position\nG1 Z3 E-3; move z axis up\nG28  ; home axis\nG92 E0; zero the extruded length\nG1 F250 E-16; Retract filament from barrel\nG92 E0; zero the extruded length again\nG90; Set to Absolute position\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heated bed\nM106 S0 ; Turn off fan\nM18;\nM117 Look...awesome! ; Put message on LCD screen
external_perimeter_speed = 80%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 40
extruder_count = 1
extruder_offset = 0x0
extruders_share_temperature = 0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 45
fill_density = 0.2
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 0
first_layer_extrusion_width = 150%
first_layer_height = 0.2
first_layer_speed = 40
first_layer_temperature = 225
g0 = 0
gap_fill_speed = 20
gcode_arcs = 1
gcode_comments = 0
gcode_flavor = reprap
gcode_output_type = REPRAP
has_fan = 1
has_heated_bed = 0
has_sd_card_reader = 1
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap_perimeter = .06
infill_speed = 100
infill_type = GRID
layer_gcode = 
layer_height = 0.2
max_fan_speed = 100
min_extrusion_before_retract = 1
min_fan_speed = 80
min_print_speed = 10
min_skirt_length = 10
notes = 
nozzle_diameter = 0.4
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
pause_gcode = G91;\nG1 F250 Z10 X10 E-16; Retract filament from barrel\nG90;\n;M104 S0; // set to holding temp\n
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 100
perimeters = 1
post_process = 
print_center = 100,110
raft_air_gap = .2
raft_extra_distance_around_part = 5
raft_fan_speed_percent = 100
raft_layers = 0
raft_print_speed = 100%
randomize_start = 0
repair_outlines_extensive_stitching = 1
repair_outlines_keep_open = 1
resolution = 0
resume_gcode = ;M109 S[temperature];  // Set print temperature \nG91;\nG1 F250 Z-10 X-10 E16; Prime filament filament from barrel\nG90;
retract_before_travel = 2
retract_layer_change = 1
retract_length = 4
retract_length_tool_change = 10
retract_lift = 0.1
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 15
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = ;Me3D - startup sequence - Me2 (G5,G6,G7) Build 30/08/14\n;Remove the ";" to activate any line\n;MAKE SURE YOU KNOW WHAT EACH LINE DOES BEFORE YOU CHANGE IT!!! The Me2 is 100% hackable and so has limited physical protection from errors in the g-code\n;M501\n;M500\n;M190 S[bed_temperature] ; // Uncomment to add your own bed temperature line\nM104 S[temperature] ; // Start heater and continue g-code\nG21 ; // set units to millimeters\n;M92 E106.707 ; // Set E-Steps\n;M92 X80 ; // Set X Steps\n;M92 Y80 ; // Set Y Steps\n;M92 Z80 ; // Set Z Steps\nM201 X3000 Y3000; // max accel print\nM202 X3000 Y3000; // max accel travel\nM205 X15; // max xyjerk mm/s\nM208 X200 Y200 Z200; // set build size\n;M17 X Y Z; // Enable motors\nG91; // Relative position\nG1 Z10; // clear bed \nG90 ; // ABS position\nG28; // home axes\nG29; // perform auto levelling at three corners\nM82 ; // use absolute distances for extrusion\nG1 Z15 F4000; // Raise Z axis clear\nG1 X-5 F4000; // Move to X axis zero\nG1 Y0 F4000;\nG92 E0; // zero the extruded length\nM109 S[temperature];  // Set print temperature and wait\nG1 F50 E30; // extrude feed stock to prime hotend barrel and purge\nG92 E0; // zero the extruded length again\nM117 Awesome!!!  // Put message on LCD screen
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 0
support_material = 1
support_material_angle = 45
support_material_create_internal_support = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_infill_angle = 45
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_pattern = honeycomb
support_material_spacing = 5
support_material_speed = 100
support_material_threshold = 60
support_material_xy_distance = 1
support_material_z_distance = 0.15
support_material_z_gap_layers = 2
support_type = GRID
temperature = 220
thin_walls = 1
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 4
travel_speed = 120
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
wipe_shield_distance = 0
wipe_tower_size = 0
z_can_be_negative = 0
z_offset = 25