mattercontrol/StaticData/PrinterSettings/Lulzbot/Mini/config.ini

avoid_crossing_perimeters = 1
bed_shape = rectangular
bed_size = 158,158
bed_temperature = 50
bed_remove_part_temperature = 60
bottom_clip_amount = 0
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 20
brim_width = 0
build_height = 150
cancel_gcode = 
center_part_on_bed = 1
complete_objects = 0
cool_extruder_lift = 0
cooling = 1
create_raft = 0
default_acceleration = 2000
disable_fan_first_layers = 1
end_gcode = M400\nM104 S0; Hotend off\nM140 S0; heated bed heater off (if you have it)\nM107; fans off\nG92 E0; set extruder to 0\nG1 E-3 F300; retract a bit to relieve pressure\nG1 X5 Y5 Z156 F10000; move to cooling positioning\nM190 R[bed_remove_part_temperature]; wait for bed to cool\nM140 S0; turn off bed temp\nG1 X145 Y175 Z156 F1000; move to cooling positioning\nM84; steppers off\nG90; absolute positioning\n
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_count = 1
extruder_offset = 0x0
extruders_share_temperature = 0
extruder_wipe_temperature = 170
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0.5
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 2.85
fill_angle = 45
fill_density = 30%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_bed_temperature = 50
first_layer_height = 0.25
first_layer_speed = 30%
first_layer_temperature = 185
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
gcode_output_type = REPRAP
has_fan = 1
has_hardware_leveling = 1
has_heated_bed = 1
has_sd_card_reader = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap_perimeter = .06
infill_speed = 60
infill_type = TRIANGLES
layer_gcode = ; LAYER:[layer_num]
layer_height = 0.2
max_fan_speed = 100
min_extrusion_before_retract = .1
min_fan_speed = 100
min_print_speed = 10
min_skirt_length = 5
notes = 
nozzle_diameter = 0.5
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
pause_gcode = 
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = .45
perimeter_speed = 35
perimeters = 3
post_process = 
print_center = 79,79
raft_air_gap = 0.5
raft_extra_distance_around_part = 5
raft_extruder = 0
raft_fan_speed_percent = 100
raft_layers = 0
raft_print_speed = 100%
randomize_start = 1
repair_outlines_extensive_stitching = 0
repair_outlines_keep_open = 0
resolution = 0
resume_gcode = 
retract_before_travel = 20
retract_layer_change = 1
retract_length = 3
retract_length_tool_change = 10
retract_lift = 0.2
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
skirt_distance = 3
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 30
small_perimeter_speed = 35
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G21; metric values\nG90; absolute positioning\nM82; set extruder to absolute mode\nM107; start with the fan off\nG92 E0; set extruder position to 0\nM140 S[bed_temperature]; get bed heating up\nG28; home all\nM109 S150; set to cleaning temp and wait\nG1 Z150 E-30 F75; suck up XXmm of filament\nM109 S[extruder_wipe_temperature]; heat up rest of way\nG1 X45 Y174 F11520; move behind scraper\nG1 Z0  F1200; CRITICAL: set Z to height of top of scraper\nG1 X45 Y174 Z-.5 F4000; wiping ; plunge into wipe pad\nG1 X55 Y172 Z-.5 F4000; wiping\nG1 X45 Y174 Z0 F4000; wiping\nG1 X55 Y172 F4000; wiping\nG1 X45 Y174 F4000; wiping\nG1 X55 Y172 F4000; wiping\nG1 X45 Y174 F4000; wiping\nG1 X55 Y172 F4000; wiping\nG1 X60 Y174 F4000; wiping\nG1 X80 Y172 F4000; wiping\nG1 X60 Y174 F4000; wiping\nG1 X80 Y172 F4000; wiping\nG1 X60 Y174 F4000; wiping\nG1 X90 Y172 F4000; wiping\nG1 X80 Y174 F4000; wiping\nG1 X100 Y172 F4000; wiping\nG1 X80 Y174 F4000; wiping\nG1 X100 Y172 F4000; wiping\nG1 X80 Y174 F4000; wiping\nG1 X100 Y172 F4000; wiping\nG1 X110 Y174 F4000; wiping\nG1 X100 Y172 F4000; wiping\nG1 X110 Y174 F4000; wiping\nG1 X100 Y172 F4000; wiping\nG1 X110 Y174 F4000; wiping\nG1 X115 Y172 Z-0.5 F1000; wipe slower and bury noz in cleanish area\nG1 Z10; raise z\nG28 X0 Y0; home x and y\nM109 S[extruder_wipe_temperature]; set to probing temp\nM204 S300; set accel for probing\nG29; Probe\nM204 S2000; set accel back to normal\nG1 X5 Y15 Z10 F5000; get out the way\nM400; clear buffer\nG4 S1; pause\nM109 S[temperature]; set extruder temp and wait\nG4 S25; wait for bed to temp up\nG1 Z2 E0 F75; extrude filament back into nozzle\nM140 S[bed_temperature]; get bed temping up during first layer
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 0
support_material = 0
support_material_angle = 45
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_infill_angle = 45
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 3
support_material_speed = 60
support_material_threshold = 30
support_material_xy_distance = 0.7
support_material_z_distance = 0.15
support_material_z_gap_layers = 1
support_type = GRID
temperature = 185
thin_walls = 1
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 4
travel_speed = 175
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 1
wipe_shield_distance = 0
wipe_tower_size = 0
z_can_be_negative = 1
z_offset = 0