8b7043abcc
Makersbots will now explicitly turn off extruder and bed so that MatterControl and the printer match states
159 lines
No EOL
4.3 KiB
INI
159 lines
No EOL
4.3 KiB
INI
avoid_crossing_perimeters = 1
|
|
bed_shape = rectangular
|
|
bed_size = 100,100
|
|
bed_temperature = 0
|
|
bottom_clip_amount = 0
|
|
bottom_solid_layers = 3
|
|
bridge_acceleration = 0
|
|
bridge_fan_speed = 100
|
|
bridge_flow_ratio = 0.9
|
|
bridge_speed = 20
|
|
brim_width = 0
|
|
build_height = 125
|
|
cancel_gcode = M104 S0 ;turn off temperature \nM140 S0 ;turn off bed temperature\nG28 X0 Y0\nM1201 ;Build End Notification MakerBot
|
|
center_part_on_bed = 1
|
|
complete_objects = 0
|
|
connect_gcode = M92 X88.8 Y88.8 Z400 E101 ;sets steps per mm for x3g driver\nM206 X285 Y150 Z0 ;sets bed offset (opposite values of bed size)
|
|
cool_extruder_lift = 0
|
|
cooling = 1
|
|
create_raft = 0
|
|
default_acceleration = 0
|
|
disable_fan_first_layers = 1
|
|
end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn off bed temperature\nG28 X0 Y0\nM84 ; disable motors\nM1201 ;Build End Norification MakerBot
|
|
external_perimeter_speed = 40
|
|
external_perimeters_first = 1
|
|
extra_perimeters = 1
|
|
extruder_clearance_height = 20
|
|
extruder_clearance_radius = 20
|
|
extruder_count = 1
|
|
extruder_offset = 0x0
|
|
extruder_wipe_temperature = 0
|
|
extruders_share_temperature = 0
|
|
extrusion_axis = E
|
|
extrusion_multiplier = 1
|
|
extrusion_width = 0
|
|
fan_always_on = 0
|
|
fan_below_layer_time = 60
|
|
filament_diameter = 1.75
|
|
fill_angle = 45
|
|
fill_density = 0.3
|
|
fill_pattern = honeycomb
|
|
first_layer_acceleration = 0
|
|
first_layer_bed_temperature = 70
|
|
first_layer_extrusion_width = 0
|
|
first_layer_height = 0.25
|
|
first_layer_speed = 10
|
|
first_layer_temperature = 205
|
|
g0 = 0
|
|
gap_fill_speed = 20
|
|
gcode_arcs = 0
|
|
gcode_comments = 0
|
|
gcode_flavor = reprap
|
|
gcode_output_type = REPRAP
|
|
has_fan = 1
|
|
has_hardware_leveling = 0
|
|
has_heated_bed = 0
|
|
has_power_control = 0
|
|
has_sd_card_reader = 0
|
|
show_reset_connection = 0
|
|
heat_extruder_before_homing = 0
|
|
infill_acceleration = 0
|
|
infill_every_layers = 1
|
|
infill_extruder = 1
|
|
infill_extrusion_width = 0
|
|
infill_first = 0
|
|
infill_only_where_needed = 0
|
|
infill_overlap_perimeter = .06
|
|
infill_speed = 40
|
|
infill_type = TRIANGLES
|
|
layer_gcode =
|
|
layer_height = 0.2
|
|
max_fan_speed = 100
|
|
min_extrusion_before_retract = .1
|
|
min_fan_speed = 35
|
|
min_print_speed = 10
|
|
min_skirt_length = 5
|
|
notes =
|
|
nozzle_diameter = 0.4
|
|
only_retract_when_crossing_perimeters = 1
|
|
ooze_prevention = 0
|
|
output_filename_format = [input_filename_base].gcode
|
|
overhangs = 1
|
|
pause_gcode =
|
|
perimeter_acceleration = 0
|
|
perimeter_extruder = 1
|
|
perimeter_extrusion_width = 0
|
|
perimeter_speed = 40
|
|
perimeters = 2
|
|
post_process =
|
|
print_center = 142.5,75
|
|
raft_air_gap = 0.25
|
|
raft_extruder = 0
|
|
raft_extra_distance_around_part = 3
|
|
raft_fan_speed_percent = 100
|
|
raft_layers = 0
|
|
raft_print_speed = 100%
|
|
bed_remove_part_temperature = 0
|
|
randomize_start = 0
|
|
repair_outlines_extensive_stitching = 0
|
|
repair_outlines_keep_open = 0
|
|
resolution = 0
|
|
resume_gcode = @restore_xyz_position\n@restore_e_position
|
|
retract_before_travel = 50
|
|
retract_layer_change = 1
|
|
retract_length = 0
|
|
retract_length_tool_change = 10
|
|
retract_lift = 0
|
|
retract_restart_extra = 0
|
|
retract_restart_extra_toolchange = 0
|
|
retract_speed = 50
|
|
skirt_distance = 3
|
|
skirt_height = 1
|
|
skirts = 1
|
|
slowdown_below_layer_time = 15
|
|
small_perimeter_speed = 50
|
|
solid_fill_pattern = rectilinear
|
|
solid_infill_below_area = 70
|
|
solid_infill_every_layers = 0
|
|
solid_infill_extrusion_width = 0
|
|
solid_infill_speed = 70
|
|
solid_shell = 0
|
|
spiral_vase = 0
|
|
standby_temperature_delta = -5
|
|
start_gcode = G28 ; home all axes\nG0 Z5 F5000 ;set warming position\nM1200 MatterControl; Build Start Notification for Makerbot\n
|
|
start_perimeters_at_concave_points = 0
|
|
start_perimeters_at_non_overhang = 0
|
|
support_material = 0
|
|
support_material_angle = 0
|
|
support_material_create_internal_support = 0
|
|
support_material_enforce_layers = 0
|
|
support_material_extruder = 1
|
|
support_material_extrusion_width = 0
|
|
support_material_infill_angle = 45
|
|
support_material_interface_extruder = 1
|
|
support_material_interface_layers = 2
|
|
support_material_interface_spacing = 1.5
|
|
support_material_pattern = rectilinear
|
|
support_material_spacing = 2.5
|
|
support_material_speed = 40
|
|
support_material_threshold = 0
|
|
support_material_xy_distance = 0.7
|
|
support_material_z_distance = 0.15
|
|
support_material_z_gap_layers = .3mm
|
|
support_type = LINES
|
|
temperature = 200
|
|
thin_walls = 1
|
|
threads = 2
|
|
toolchange_gcode =
|
|
top_infill_extrusion_width = 0
|
|
top_solid_infill_speed = 80
|
|
top_solid_layers = 4
|
|
travel_speed = 110
|
|
use_firmware_retraction = 0
|
|
use_relative_e_distances = 0
|
|
vibration_limit = 0
|
|
wipe = 0
|
|
wipe_shield_distance = 0
|
|
wipe_tower_size = 0
|
|
z_can_be_negative = 0
|
|
z_offset = 0 |