8b7043abcc
Makersbots will now explicitly turn off extruder and bed so that MatterControl and the printer match states
163 lines
No EOL
4.4 KiB
INI
163 lines
No EOL
4.4 KiB
INI
avoid_crossing_perimeters = 1
|
|
bed_shape = rectangular
|
|
bed_size = 225,150
|
|
bed_temperature = 50
|
|
bottom_clip_amount = 0
|
|
bottom_solid_layers = 2
|
|
bridge_acceleration = 0
|
|
bridge_fan_speed = 100
|
|
bridge_flow_ratio = 0.9
|
|
bridge_speed = 20
|
|
brim_width = 0
|
|
build_height = 0
|
|
cancel_gcode = M104 S0 ;turn off temperature \nM140 S0 ;turn off bed temperature\nG28 X0 Y0\nM1201 ;Build End Notification MakerBot
|
|
center_part_on_bed = 1
|
|
complete_objects = 0
|
|
connect_gcode = M92 X94.5 Y94.5 Z400 E96 ;sets steps per mm for x3g driver\nM206 X230 Y155 Z0 ;sets home offset (opposite values of bed size)
|
|
cool_extruder_lift = 0
|
|
print_leveling_solution = 3 Point Plane
|
|
print_leveling_method = Manual
|
|
print_leveling_required_to_print = 0
|
|
manual_probe_paper_width = .1
|
|
cooling = 1
|
|
create_raft = 0
|
|
default_acceleration = 0
|
|
disable_fan_first_layers = 1
|
|
end_gcode = M104 S0 ; turn off temperature\nM140 S0 ; turn off bed temperature\nG28 X0 Y0\nM84 ; disable motors\nM1201 ;Build End Norification MakerBot
|
|
external_perimeter_speed = 40
|
|
external_perimeters_first = 1
|
|
extra_perimeters = 1
|
|
extruder_clearance_height = 20
|
|
extruder_clearance_radius = 20
|
|
extruder_count = 2
|
|
extruder_offset = 0x0
|
|
extruder_wipe_temperature = 0
|
|
extruders_share_temperature = 0
|
|
extrusion_axis = E
|
|
extrusion_multiplier = 1
|
|
extrusion_width = 0
|
|
fan_always_on = 0
|
|
fan_below_layer_time = 60
|
|
filament_diameter = 1.75
|
|
fill_angle = 45
|
|
fill_density = 0.3
|
|
fill_pattern = honeycomb
|
|
first_layer_acceleration = 0
|
|
first_layer_bed_temperature = 60
|
|
first_layer_extrusion_width = 0
|
|
first_layer_height = 0.2
|
|
first_layer_speed = 10
|
|
first_layer_temperature = 205
|
|
g0 = 0
|
|
gap_fill_speed = 20
|
|
gcode_arcs = 0
|
|
gcode_comments = 0
|
|
gcode_flavor = reprap
|
|
gcode_output_type = REPRAP
|
|
has_fan = 0
|
|
has_hardware_leveling = 0
|
|
has_heated_bed = 1
|
|
has_power_control = 0
|
|
has_sd_card_reader = 0
|
|
show_reset_connection = 0
|
|
heat_extruder_before_homing = 0
|
|
infill_acceleration = 0
|
|
infill_every_layers = 1
|
|
infill_extruder = 1
|
|
infill_extrusion_width = 0
|
|
infill_first = 0
|
|
infill_only_where_needed = 0
|
|
infill_overlap_perimeter = .06
|
|
infill_speed = 40
|
|
infill_type = TRIANGLES
|
|
layer_gcode =
|
|
layer_height = 0.2
|
|
max_fan_speed = 100
|
|
min_extrusion_before_retract = .1
|
|
min_fan_speed = 35
|
|
min_print_speed = 10
|
|
min_skirt_length = 5
|
|
notes =
|
|
nozzle_diameter = 0.4
|
|
only_retract_when_crossing_perimeters = 1
|
|
ooze_prevention = 0
|
|
output_filename_format = [input_filename_base].gcode
|
|
overhangs = 1
|
|
pause_gcode =
|
|
perimeter_acceleration = 0
|
|
perimeter_extruder = 1
|
|
perimeter_extrusion_width = 0
|
|
perimeter_speed = 40
|
|
perimeters = 2
|
|
post_process =
|
|
print_center = 115,77.5
|
|
raft_air_gap = .2
|
|
raft_extruder = 0
|
|
raft_extra_distance_around_part = 3
|
|
raft_fan_speed_percent = 100
|
|
raft_layers = 0
|
|
raft_print_speed = 100%
|
|
bed_remove_part_temperature = 0
|
|
randomize_start = 0
|
|
repair_outlines_extensive_stitching = 0
|
|
repair_outlines_keep_open = 0
|
|
resolution = 0
|
|
resume_gcode = @restore_xyz_position\n@restore_e_position
|
|
retract_before_travel = 50
|
|
retract_layer_change = 1
|
|
retract_length = 0
|
|
retract_length_tool_change = 10
|
|
retract_lift = 0
|
|
retract_restart_extra = 0
|
|
retract_restart_extra_toolchange = 0
|
|
retract_speed = 50
|
|
skirt_distance = 3
|
|
skirt_height = 1
|
|
skirts = 1
|
|
slowdown_below_layer_time = 15
|
|
small_perimeter_speed = 50
|
|
solid_fill_pattern = rectilinear
|
|
solid_infill_below_area = 70
|
|
solid_infill_every_layers = 0
|
|
solid_infill_extrusion_width = 0
|
|
solid_infill_speed = 70
|
|
solid_shell = 0
|
|
spiral_vase = 0
|
|
standby_temperature_delta = -5
|
|
start_gcode = G28 ; home all axes\nG0 Z5 F5000 ;set warming position\nM1200 MatterControl; Build Start Notification for Makerbot\n
|
|
start_perimeters_at_concave_points = 0
|
|
start_perimeters_at_non_overhang = 0
|
|
support_material = 0
|
|
support_material_angle = 0
|
|
support_material_create_internal_support = 0
|
|
support_material_enforce_layers = 0
|
|
support_material_extruder = 1
|
|
support_material_extrusion_width = 0
|
|
support_material_infill_angle = 45
|
|
support_material_interface_extruder = 1
|
|
support_material_interface_layers = 2
|
|
support_material_interface_spacing = 1.5
|
|
support_material_pattern = rectilinear
|
|
support_material_spacing = 2.5
|
|
support_material_speed = 60
|
|
support_material_threshold = 0
|
|
support_material_xy_distance = 0.7
|
|
support_material_z_distance = 0.15
|
|
support_material_z_gap_layers = .3mm
|
|
support_type = LINES
|
|
temperature = 205
|
|
thin_walls = 1
|
|
threads = 2
|
|
toolchange_gcode =
|
|
top_infill_extrusion_width = 0
|
|
top_solid_infill_speed = 80
|
|
top_solid_layers = 4
|
|
travel_speed = 110
|
|
use_firmware_retraction = 0
|
|
use_relative_e_distances = 0
|
|
vibration_limit = 0
|
|
wipe = 0
|
|
wipe_shield_distance = 0
|
|
wipe_tower_size = 0
|
|
z_can_be_negative = 0
|
|
z_offset = 0 |