289 lines
No EOL
9.8 KiB
Text
289 lines
No EOL
9.8 KiB
Text
{
|
|
"DocumentVersion": 201606271,
|
|
"ID": "2+-5686919578517504",
|
|
"StagedUserSettings": {},
|
|
"Macros": [],
|
|
"OemLayer": {
|
|
"avoid_crossing_perimeters": "1",
|
|
"bed_remove_part_temperature": "0",
|
|
"bed_shape": "rectangular",
|
|
"bed_size": "223,223",
|
|
"bed_temperature": "70",
|
|
"bottom_clip_amount": "0",
|
|
"bridge_acceleration": "0",
|
|
"bridge_fan_speed": "100",
|
|
"bridge_flow_ratio": "1",
|
|
"bridge_speed": "20",
|
|
"brim_width": "0",
|
|
"build_height": "205",
|
|
"cancel_gcode": "G28",
|
|
"center_part_on_bed": "1",
|
|
"complete_objects": "0",
|
|
"connect_gcode": "",
|
|
"cool_extruder_lift": "0",
|
|
"cooling": "1",
|
|
"create_raft": "0",
|
|
"default_acceleration": "0",
|
|
"disable_fan_first_layers": "1",
|
|
"end_gcode": "M104 S0 ;extruder heater off\\nM140 S0 ;heated bed heater off (if you have it)\\nG91 ;relative positioning\\nG1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\\nG1 Z+0.5 E-5 X-20 Y-20 F1300 ;move Z up a bit and retract filament even more\\nG28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way\\nM84 ;steppers off\\nG90 ;absolute positioning",
|
|
"external_perimeter_speed": "70%",
|
|
"external_perimeters_first": "0",
|
|
"extra_perimeters": "1",
|
|
"extruder_clearance_height": "20",
|
|
"extruder_clearance_radius": "20",
|
|
"extruder_count": "1",
|
|
"extruder_offset": "0x0,0x0,0x0,0x0",
|
|
"extruder_wipe_temperature": "0",
|
|
"extruders_share_temperature": "0",
|
|
"extrusion_axis": "E",
|
|
"extrusion_multiplier": "1",
|
|
"extrusion_width": "0",
|
|
"fan_always_on": "0",
|
|
"fan_below_layer_time": "60",
|
|
"filament_diameter": "2.85",
|
|
"fill_angle": "45",
|
|
"fill_density": "30%",
|
|
"fill_pattern": "honeycomb",
|
|
"first_layer_acceleration": "0",
|
|
"first_layer_bed_temperature": "75",
|
|
"first_layer_height": "0.3",
|
|
"first_layer_speed": "20",
|
|
"first_layer_temperature": "205",
|
|
"g0": "0",
|
|
"gap_fill_speed": "20",
|
|
"gcode_arcs": "0",
|
|
"gcode_comments": "0",
|
|
"gcode_flavor": "reprap",
|
|
"gcode_output_type": "REPRAP",
|
|
"has_fan": "1",
|
|
"has_hardware_leveling": "0",
|
|
"has_heated_bed": "1",
|
|
"has_power_control": "0",
|
|
"has_sd_card_reader": "1",
|
|
"heat_extruder_before_homing": "0",
|
|
"infill_acceleration": "0",
|
|
"infill_every_layers": "1",
|
|
"infill_extruder": "1",
|
|
"infill_extrusion_width": "0",
|
|
"infill_first": "0",
|
|
"infill_only_where_needed": "0",
|
|
"infill_overlap_perimeter": "0.1",
|
|
"infill_speed": "45",
|
|
"infill_type": "TRIANGLES",
|
|
"layer_height": "0.2",
|
|
"manual_probe_paper_width": ".1",
|
|
"max_fan_speed": "100",
|
|
"min_extrusion_before_retract": "0.05",
|
|
"min_fan_speed": "100",
|
|
"min_print_speed": "10",
|
|
"min_skirt_length": "5",
|
|
"notes": "",
|
|
"nozzle_diameter": "0.4",
|
|
"only_retract_when_crossing_perimeters": "1",
|
|
"ooze_prevention": "0",
|
|
"output_filename_format": "[input_filename_base].gcode",
|
|
"overhangs": "1",
|
|
"pause_gcode": "",
|
|
"perimeter_acceleration": "0",
|
|
"perimeter_extruder": "1",
|
|
"perimeter_extrusion_width": "0",
|
|
"perimeter_speed": "40",
|
|
"perimeters": "2",
|
|
"post_process": "",
|
|
"print_center": "111,111",
|
|
"print_leveling_method": "Manual",
|
|
"print_leveling_required_to_print": "0",
|
|
"print_leveling_solution": "3 Point Plane",
|
|
"raft_air_gap": "0.22",
|
|
"raft_extra_distance_around_part": "5",
|
|
"raft_extruder": "0",
|
|
"raft_fan_speed_percent": "100",
|
|
"raft_layers": "0",
|
|
"raft_print_speed": "100%",
|
|
"randomize_start": "0",
|
|
"repair_outlines_extensive_stitching": "0",
|
|
"repair_outlines_keep_open": "0",
|
|
"resolution": "0",
|
|
"resume_gcode": "",
|
|
"retract_before_travel": "10",
|
|
"retract_layer_change": "1",
|
|
"retract_length": "4.5",
|
|
"retract_length_tool_change": "16.5",
|
|
"retract_lift": "0",
|
|
"retract_restart_extra": "0",
|
|
"retract_restart_extra_toolchange": "0",
|
|
"retract_speed": "60",
|
|
"show_reset_connection": "0",
|
|
"skirt_distance": "3",
|
|
"skirt_height": "1",
|
|
"skirts": "1",
|
|
"slowdown_below_layer_time": "25",
|
|
"small_perimeter_speed": "30",
|
|
"solid_fill_pattern": "rectilinear",
|
|
"solid_infill_below_area": "70",
|
|
"solid_infill_every_layers": "0",
|
|
"solid_infill_extrusion_width": "0",
|
|
"solid_infill_speed": "60",
|
|
"solid_shell": "0",
|
|
"spiral_vase": "0",
|
|
"standby_temperature_delta": "-5",
|
|
"start_gcode": "G21 ;metric values\\nG90 ;absolute positioning\\nM82 ;set extruder to absolute mode\\nM107 ;start with the fan off\\nG28 X0 Y0 ;move X/Y to min endstops\\nG28 Z0 ;move Z to min endstops\\nM190 S[bed_temperature]\\nG1 Z15.0 F1800 ;move the platform down 15mm\\nG1 Y10 F4000\\nM109 S[temperature]\\nG92 E0 ;zero the extruded length\\nG1 F200 E30 ;extrude 30mm of feed stock\\nG92 E0 ;zero the extruded length again\\nG1 F130\\nM117 Printing... \t;Put printing message on LCD screen",
|
|
"start_perimeters_at_concave_points": "0",
|
|
"start_perimeters_at_non_overhang": "0",
|
|
"support_material": "0",
|
|
"support_material_angle": "45",
|
|
"support_material_enforce_layers": "0",
|
|
"support_material_extruder": "1",
|
|
"support_material_extrusion_width": "0",
|
|
"support_material_infill_angle": "45",
|
|
"support_material_interface_extruder": "1",
|
|
"support_material_interface_layers": "1mm",
|
|
"support_material_interface_spacing": "0",
|
|
"support_material_pattern": "honeycomb",
|
|
"support_material_spacing": "2.5",
|
|
"support_material_speed": "30",
|
|
"support_material_threshold": "45",
|
|
"support_material_xy_distance": "1",
|
|
"support_material_z_distance": "0.15",
|
|
"support_material_z_gap_layers": "1",
|
|
"support_type": "LINES",
|
|
"temperature": "210",
|
|
"thin_walls": "1",
|
|
"threads": "2",
|
|
"toolchange_gcode": "",
|
|
"top_infill_extrusion_width": "0",
|
|
"top_solid_infill_speed": "35",
|
|
"top_solid_layers": "1mm",
|
|
"travel_speed": "150",
|
|
"use_firmware_retraction": "0",
|
|
"use_relative_e_distances": "0",
|
|
"vibration_limit": "0",
|
|
"wipe": "0",
|
|
"wipe_shield_distance": "0",
|
|
"wipe_tower_size": "0",
|
|
"z_can_be_negative": "0",
|
|
"z_offset": "0",
|
|
"make": "Ultimaker",
|
|
"model": "2+",
|
|
"created_date": "2017-08-30T16:22:50.418Z",
|
|
"baud_rate": "250000",
|
|
"default_material_presets": "PLA",
|
|
"default_quality_presets": "Normal",
|
|
"windows_driver": "MHSerial.inf",
|
|
"calibration_files": "Calibration - Circle.stl",
|
|
"active_theme_name": "Blue - Light",
|
|
"z_homes_to_max": "1",
|
|
"recover_is_enabled": "1",
|
|
"support_material_create_perimeter": "1",
|
|
"active_quality_key": "",
|
|
"support_air_gap": "0.4",
|
|
"support_material_create_internal_support": "1"
|
|
},
|
|
"ActiveQualityKey": "",
|
|
"MaterialSettingsKeys": [
|
|
"9be80dcb-d16a-4f31-ab79-697555f33381"
|
|
],
|
|
"MaterialLayers": [
|
|
{
|
|
"layer_name": "ABS",
|
|
"filament_density": "1.04",
|
|
"layer_id": "7dcec9ed-3229-4cb8-87fe-d9d77020ec0f",
|
|
"bed_temperature": "90",
|
|
"bridge_fan_speed": "50",
|
|
"max_fan_speed": "0",
|
|
"min_fan_speed": "0",
|
|
"temperature": "220"
|
|
},
|
|
{
|
|
"layer_name": "PET",
|
|
"layer_id": "6b3c97f8-6c2b-4599-a89c-09c46250886d",
|
|
"bed_temperature": "60",
|
|
"bridge_fan_speed": "50",
|
|
"max_fan_speed": "0",
|
|
"min_fan_speed": "0",
|
|
"temperature": "260",
|
|
"filament_density": "1.38",
|
|
"fill_density": "75%",
|
|
"infill_overlap_perimeter": "0.2",
|
|
"perimeters": "2",
|
|
"retract_length": "6.5",
|
|
"infill_speed": "45",
|
|
"top_solid_infill_speed": "40",
|
|
"perimeter_speed": "40"
|
|
},
|
|
{
|
|
"layer_name": "PLA",
|
|
"filament_density": "1.24",
|
|
"layer_id": "9be80dcb-d16a-4f31-ab79-697555f33381",
|
|
"bed_temperature": "60",
|
|
"bridge_fan_speed": "100",
|
|
"max_fan_speed": "100",
|
|
"min_fan_speed": "100",
|
|
"temperature": "210"
|
|
},
|
|
{
|
|
"layer_name": "NylonX",
|
|
"layer_id": "457b09e1-5ac9-4c4b-93ec-657d4214f46e",
|
|
"brims": "10",
|
|
"temperature": "260",
|
|
"bed_temperature": "71"
|
|
},
|
|
{
|
|
"layer_name": "FLEX",
|
|
"layer_id": "7137b3d6-ba19-4b92-99af-19d338d96183",
|
|
"fill_density": "10%",
|
|
"infill_overlap_perimeter": "0.2",
|
|
"infill_speed": "20",
|
|
"top_solid_infill_speed": "15",
|
|
"perimeter_speed": "15",
|
|
"temperature": "245",
|
|
"bed_temperature": "60",
|
|
"retract_length": "0",
|
|
"extrusion_multiplier": "1.25",
|
|
"perimeters": "2",
|
|
"support_material_create_perimeter": "1"
|
|
}
|
|
],
|
|
"QualityLayers": [
|
|
{
|
|
"layer_name": "Fast",
|
|
"layer_id": "05492883-540e-4b5a-bbc1-3564103bbf11",
|
|
"external_perimeter_speed": "40",
|
|
"fill_density": "0.1",
|
|
"first_layer_speed": "30",
|
|
"infill_speed": "100",
|
|
"layer_height": "0.15",
|
|
"perimeter_speed": "80"
|
|
},
|
|
{
|
|
"layer_name": "High",
|
|
"layer_id": "933c8d4f-bdc2-4272-84f0-9f2b6cc682c1",
|
|
"external_perimeter_speed": "30",
|
|
"fill_density": "0.2",
|
|
"first_layer_speed": "20",
|
|
"infill_speed": "80",
|
|
"layer_height": "0.06",
|
|
"perimeter_speed": "60"
|
|
},
|
|
{
|
|
"layer_name": "Normal",
|
|
"layer_id": "f79e8c87-63d3-4f22-86f5-dbc97ac306fd",
|
|
"external_perimeter_speed": "30",
|
|
"fill_density": "0.2",
|
|
"first_layer_speed": "20",
|
|
"infill_speed": "80",
|
|
"layer_height": "0.1",
|
|
"perimeter_speed": "60"
|
|
},
|
|
{
|
|
"layer_name": "Ulti",
|
|
"layer_id": "36423e20-9c3e-4fcd-83ae-637079ff9de9",
|
|
"external_perimeter_speed": "30",
|
|
"fill_density": "0.2",
|
|
"first_layer_speed": "20",
|
|
"infill_speed": "80",
|
|
"layer_height": "0.04",
|
|
"perimeter_speed": "60"
|
|
}
|
|
]
|
|
} |