avoid_crossing_perimeters = 1
bottom_solid_layers = 3
bridge_acceleration = 500
bridge_flow_ratio = 0.9
bridge_speed = 25
brim_width = 1
complete_objects = 1
default_acceleration = 1200
external_perimeter_speed = 80%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 35
extruder_clearance_radius = 40
extrusion_width = 0.7
fill_angle = 45
fill_density = 0.4
fill_pattern = honeycomb
first_layer_acceleration = 1200
first_layer_extrusion_width = 0
first_layer_height = 0.1
first_layer_speed = 70%
gap_fill_speed = 10
gcode_comments = 1
infill_acceleration = 200
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 1
infill_only_where_needed = 0
infill_speed = 60
layer_height = 0.2
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 
perimeter_acceleration = 900
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 50
perimeters = 1
post_process = 
raft_layers = 0
randomize_start = 1
resolution = 0
skirt_distance = 0.8
skirt_height = 2
skirts = 10
small_perimeter_speed = 30
solid_fill_pattern = concentric
solid_infill_below_area = 70
solid_infill_every_layers = 20
solid_infill_extrusion_width = 0
solid_infill_speed = 70%
spiral_vase = 0
standby_temperature_delta = -5
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 0
support_material = 0
support_material_angle = 45
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 2.5
support_material_pattern = honeycomb
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0.5
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 160
bed_temperature = 0
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1.0
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 2.92
first_layer_bed_temperature = 0
first_layer_temperature = 195
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
slowdown_below_layer_time = 30
temperature = 185
bed_size = 230,230
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nG91 ;  Set distance mode to relative value mode\nG1 E-5 F60 ; Retract E=- 5mm, rate F = 200mm/min  \nG90 ; set distance mode to absolute value mode\nM84   ; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.7
print_center = 120,130
retract_before_travel = 3
retract_layer_change = 0
retract_length = 7
retract_length_toolchange = 10
retract_lift = 0.1
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 35
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\nM109 S[first_layer_temperature] ; Set extruder temp S=180 degrees and wait\nG91 ;  Set distance mode to relative value mode;\nG1 E25 F150 ; Extrude E= 25mm, rate F = 150mm/min  \nG90 ; set distance mode to absolute value mode
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 1
z_offset = -0.4