avoid_crossing_perimeters = 1
bed_shape = rectangular
bed_size = 230,230
bed_temperature = 0
bottom_clip_amount = 0
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 0.8
bridge_speed = 30
brim_width = 0.5
build_height = 200
cancel_gcode = G91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nG1 E-10 F500 ; Retract Extruder\nG90;\nG28 X0;   Home X axis\nG1 Y225 F3000; bring plate to front\nM84;
center_part_on_bed = 0
complete_objects = 1
connect_gcode = 
cool_extruder_lift = 0
print_leveling_solution = 7 Point Disk
print_leveling_method = Manual
print_leveling_required_to_print = 1
manual_probe_paper_width = .1
cooling = 1
create_raft = 1
default_acceleration = 0
disable_fan_first_layers = 1
end_gcode = M104 S0 ; turn off temperature\nG91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nG1 E-15 F500 ; Retract Extruder\nG90;\nG28 X0  ; home X axis\nG1 Y225 F3000; bring plate to front\nM84;
external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 35
extruder_clearance_radius = 40
extruder_count = 1
extruder_offset = 0x0
extruder_wipe_temperature = 0
extruders_share_temperature = 0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.74
fill_angle = 45
fill_density = 50%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_bed_temperature = 0
first_layer_extrusion_width = 110%
first_layer_height = 0.15
first_layer_speed = 20
first_layer_temperature = 210
g0 = 0
gap_fill_speed = 15
gcode_arcs = 0
gcode_comments = 1
gcode_flavor = reprap
gcode_output_type = REPRAP
has_fan = 0
has_hardware_leveling = 0
has_heated_bed = 0
has_power_control = 0
has_sd_card_reader = 0
show_reset_connection = 1
heat_extruder_before_homing = 1
include_firmware_updater = Simple Arduino
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 1
infill_overlap_perimeter = 0
infill_speed = 30
infill_type = LINES
layer_height = 0.3
max_fan_speed = 100
min_extrusion_before_retract = 0.003
min_fan_speed = 35
min_print_speed = 14
min_skirt_length = 2
notes = 
nozzle_diameter = 0.55
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
pause_gcode = G1 X0 Y0 F3000; home all axes\nM84 S0
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process = 
print_center = 120,130
raft_air_gap = 0.3
raft_extruder = 0
raft_extra_distance_around_part = 4
raft_fan_speed_percent = 100
raft_layers = 0
raft_print_speed = 30
bed_remove_part_temperature = 0
randomize_start = 1
repair_outlines_extensive_stitching = 0
repair_outlines_keep_open = 1
resolution = 0
resume_gcode = 
retract_before_travel = 3
retract_layer_change = 0
retract_length = 1
retract_length_tool_change = 10
retract_lift = 0.4
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 25
skirt_distance = 0.7
skirt_height = 2
skirts = 3
slowdown_below_layer_time = 20
small_perimeter_speed = 10
solid_fill_pattern = concentric
solid_infill_below_area = 70
solid_infill_every_layers = 20
solid_infill_extrusion_width = 0
solid_infill_speed = 90%
solid_shell = 0
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = M92 X 31.6900 Y31.5515 Z1283 E70.770\nM205 X40\nG28 ; home all axes\nG91\nG1 E30 F100 ;  Extrude primer filament\nG90\nM109 S208 B250 F0.5
start_perimeters_at_concave_points = 1
start_perimeters_at_non_overhang = 1
support_material = 0
support_material_angle = 45
support_material_create_internal_support = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 100%
support_material_infill_angle = 60
support_material_interface_extruder = 1
support_material_interface_layers = 1.5mm
support_material_interface_spacing = 0
support_material_pattern = honeycomb
support_material_spacing = 2
support_material_speed = 30
support_material_threshold = 20
support_material_xy_distance = 3.25
support_material_z_distance = 0.15
support_material_z_gap_layers = 0.6mm
support_type = LINES
temperature = 208
thin_walls = 1
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 35
top_solid_layers = 2mm
travel_speed = 120
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 1
wipe_shield_distance = 0
wipe_tower_size = 0
z_can_be_negative = 0
z_offset = 0