avoid_crossing_perimeters = 1
bed_shape = rectangular
bed_size = 215,215
bed_temperature = 0
bottom_clip_amount = 0
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 15
brim_width = 0
build_height = 205
cancel_gcode = G91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nG1 E-10 F500 ; Retract Extruder\nG90;\nG28 Y;   Home Y axis\nG1 X210 Y10 F2000; bring plate to front\nM84;
center_part_on_bed = 0
complete_objects = 0
connect_gcode = 
cool_extruder_lift = 0
print_leveling_solution = 7 Point Disk
print_leveling_method = Manual
print_leveling_required_to_print = 1
manual_probe_paper_width = .1
cooling = 1
create_raft = 1
default_acceleration = 0
disable_fan_first_layers = 0
end_gcode = M104 T0 S0 ; turn off temperature\nM104 T1 S0 ; turn off temperature\nG91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nT0\nG1 E-40 F800 ; Retract Extruder\nT1\nG1 E-40 F800\nG90;\nG1 X210 Y10 F2000;\nM84;
external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_count = 2
extruder_offset = 0x0,31.55x-0.3,0x0,0x0
extruder_wipe_temperature = 0
extruders_share_temperature = 0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.79
fill_angle = 45
fill_density = 10%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 75
first_layer_extrusion_width = 100%
first_layer_height = 0.15
first_layer_speed = 20
first_layer_temperature = 205
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
gcode_output_type = REPRAP
has_fan = 1
has_hardware_leveling = 0
has_heated_bed = 0
has_power_control = 0
has_sd_card_reader = 1
show_reset_connection = 1
heat_extruder_before_homing = 1
include_firmware_updater = Simple Arduino
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap_perimeter = 0
infill_speed = 30
infill_type = LINES
layer_height = 0.35
max_fan_speed = 100
min_extrusion_before_retract = 0.003
min_fan_speed = 80
min_print_speed = 7
min_skirt_length = 3
notes = 
nozzle_diameter = 0.48
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
pause_gcode = G1 X0 Y215 F2000; home axes\nM84 S0
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process = 
print_center = 110,110
raft_air_gap = 0.25
raft_extruder = 1
raft_extra_distance_around_part = 5
raft_fan_speed_percent = 40
raft_layers = 0
raft_print_speed = 35
bed_remove_part_temperature = 0
randomize_start = 0
repair_outlines_extensive_stitching = 1
repair_outlines_keep_open = 1
resolution = 0
resume_gcode = 
retract_before_travel = 4
retract_layer_change = 1
retract_length = 1
retract_length_tool_change = 25
retract_lift = 0.35
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 15
skirt_distance = 2
skirt_height = 1
skirts = 3
slowdown_below_layer_time = 20
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
solid_shell = 0
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = M42 P5 S128\nG28 X0 Y0 ; home all axes\nM106 S160\nG28 X0 Y0 Z0\nG91\nG1 Z5 F3000\nT0\nG1 E35 F100 ;  Extrude primer filament\nT1\nG1 E35 F100\nT0\nG1 Z5 F3000
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 0
support_material = 0
support_material_angle = 45
support_material_create_internal_support = 1
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 100%
support_material_infill_angle = 90
support_material_interface_extruder = 1
support_material_interface_layers = 1mm
support_material_interface_spacing = 0
support_material_pattern = honeycomb
support_material_spacing = 2.5
support_material_speed = 35
support_material_threshold = 20
support_material_xy_distance = 0.7
support_material_z_distance = 0.15
support_material_z_gap_layers = 3
support_type = LINES
temperature = 200
thin_walls = 1
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 1.4mm
travel_speed = 95
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 1
wipe_shield_distance = 0
wipe_tower_size = 0
z_can_be_negative = 0
z_offset = -0.2