avoid_crossing_perimeters = 1
bed_shape = rectangular
bed_size = 200,220
bed_temperature = 0
bottom_clip_amount = 0
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 50
brim_width = 0
build_height = 180
cancel_gcode = G91; Set to Relative position\nG1 Z3 E-3; move z axis up\nG28; home axis\nG1 F250 E-16; Retract filament from barrel\nG90; Set to Absolute position\nM104 S0; turn off temperature\nM140 S0; turn off heated bed\nM106 S0; Turn off fan\nM18;\nM117 Print cancelled
center_part_on_bed = 1
complete_objects = 0
connect_gcode = 
cool_extruder_lift = 0
print_leveling_solution = 3 Point Plane
print_leveling_method = Manual
print_leveling_required_to_print = 0
manual_probe_paper_width = .1
cooling = 1
create_raft = 0
default_acceleration = 0
disable_fan_first_layers = 1
end_gcode = G91; Set to Relative position\nG1 Z3 E-3; move z axis up\nG28  ; home axis\nG1 F250 E-16; Retract filament from barrel\nG90; Set to Absolute position\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heated bed\nM106 S0 ; Turn off fan\nM18;\nM117 All Done!!!
external_perimeter_speed = 80%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 40
extruder_count = 1
extruder_offset = 0x0
extruder_wipe_temperature = 0
extruders_share_temperature = 0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 45
fill_density = 15%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_bed_temperature = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_speed = 20
first_layer_temperature = 210
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
gcode_output_type = REPRAP
has_fan = 1
has_hardware_leveling = 1
has_heated_bed = 0
has_power_control = 0
has_sd_card_reader = 1
show_reset_connection = 0
heat_extruder_before_homing = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap_perimeter = 0.05
infill_speed = 60
infill_type = GRID
layer_gcode = ; LAYER:[layer_num]
layer_height = 0.2
layer_to_pause = 
max_fan_speed = 80
min_extrusion_before_retract = 0.005
min_fan_speed = 60
min_print_speed = 3
min_skirt_length = 1
notes = 
nozzle_diameter = 0.4
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
pause_gcode = G91;\nG1 F250 Z10 X10 E-16; Retract filament from barrel\nG90;\nM104 S0; set to holding temp\nM117 Print paused
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
external_perimeter_extrusion_width = 100%
perimeter_speed = 80
perimeters = 2
post_process = 
print_center = 100,110
raft_air_gap = .2
raft_extruder = 0
raft_extra_distance_around_part = 5
raft_fan_speed_percent = 100
raft_layers = 0
raft_print_speed = 100%
bed_remove_part_temperature = 0
randomize_start = 0
repair_outlines_extensive_stitching = 1
repair_outlines_keep_open = 1
resolution = 0
resume_gcode = M117 Print resumed\nM109 S[temperature]; Set print temperature \nG91;\nG1 F250 Z-10 X-10 E16; Prime filament from barrel\nG90;
retract_before_travel = 0.8
retract_layer_change = 0
retract_length = 2.5
retract_length_tool_change = 10
retract_lift = 1
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_when_changing_islands = 1
retract_speed = 50
skirt_distance = 3
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 8
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_below_area = 5
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
solid_shell = 0
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = ;Me3D - MC1.5 startup sequence - Me2 (G5,G6,G7) Build 02/16\n;Remove the ";" to activate any line\n;MAKE SURE YOU KNOW WHAT EACH LINE DOES BEFORE YOU CHANGE IT!!! The Me2 is 100% hackable and so has limited physical protection from errors in the g-code\nM104 S[temperature] ; Start heater and continue g-code\nG21 ; set units to millimeters\nM201 X5000 Y5000; max accel print\nM202 X5000 Y5000; max accel travel\nM205 X15; max xyjerk mm/s\nG92; Zero current head position\nG91; Relative position\nG1 Z10; clear bed \nG90 ; ABS position\nG28; home axes\nG29; perform auto levelling at three corners\nM82 ; use absolute distances for extrusion\nG1 Z15 F4000; Raise Z axis clear\nG1 X-5 F4000; Move to X axis zero\nG1 Y5 F4000;\nG92 E0; zero the extruded length\nM109 S[temperature]; Set print temperature and wait\nG1 F100 E19; extrude feed stock to prime hotend barrel and purge\n; Create purge line\nG1 Z[z_offset] F1000; z_offset variable only available in MC1.2.3 and above\nG91; Relative motion \nG1 Z0.3;\nG1 X10 Y1 F1000; Change this value to move the position of the line on the bed\nG1 X120 E20;\nG1 Y1;\nG1 X-100 E16.5;\nG1 X-20 E2;\nG1 X10 Y-3 F500;\nG1 Y5 F4000;\nG92 E0;\nG90;\nG92 E0; zero the extruded length again\nM117 OK...let's print;
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 0
support_air_gap = .3
support_material = 1
support_material_angle = 45
support_material_percent = 10
support_material_create_internal_support = 0
support_material_create_perimeter = 1
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_infill_angle = 45
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 100
support_material_threshold = 19
support_material_xy_distance = 1
support_material_z_distance = 0.15
support_material_z_gap_layers = 3
support_type = LINES
temperature = 217
thin_walls = 1
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 90%
top_solid_infill_speed = 50
top_solid_layers = 4
travel_speed = 120
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
wipe_shield_distance = 0
wipe_tower_size = 0
z_can_be_negative = 0
z_offset = 25