avoid_crossing_perimeters = 1
bed_shape = rectangular
bed_size = 200,240
bed_temperature = 40
bottom_clip_amount = 0
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 30
brim_width = 0
build_height = 200
cancel_gcode = M104 S0   ;extruder heater off\nM140 S0   ;heated bed heater off (if you have it)\nG91 ;relative positioning\nG1 E-2 F9000 ;retract the filament a bit before lifting the nozzle\nG1 Z+0.5 E-5 X-10 Y+10 F9000 ;move Z up a bit and retract filament even more\nG28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way\nM84 ;steppers off\nG90 ;absolute positioning\n
center_part_on_bed = 0
complete_objects = 0
cool_extruder_lift = 0
cooling = 1
create_raft = 0
default_acceleration = 0
disable_fan_first_layers = 0
end_gcode = M104 S0   ;extruder heater off\nM140 S0   ;heated bed heater off (if you have it)\nG91 ;relative positioning\nG1 E-2 F9000 ;retract the filament a bit before lifting the nozzle\nG1 Z+0.5 E-5 X-10 Y+10 F9000 ;move Z up a bit and retract filament even more\nG28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way\nM84 ;steppers off\nG90 ;absolute positioning\nM81 ;Turns power off from the printer\n
external_perimeter_speed = 60
external_perimeters_first = 1
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_count = 2
extruder_offset = 0x0,0x0,0x0,0x0
extruders_share_temperature = 0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 45
fill_density = 30%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 75
first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_speed = 20
first_layer_temperature = 205
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
gcode_output_type = REPRAP
has_fan = 1
has_hardware_leveling = 0
has_heated_bed = 1
has_sd_card_reader = 1
heat_extruder_before_homing = 1
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap_perimeter = .06
infill_speed = 40
infill_type = TRIANGLES
layer_gcode = 
layer_height = 0.2
max_fan_speed = 100
min_extrusion_before_retract = 0.5
min_fan_speed = 100
min_print_speed = 15
min_skirt_length = 2
notes = 
nozzle_diameter = 0.4
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
pause_gcode = G91 ;relative positioning\nG1 E-15 F9000 ;retract the filament a bit before lifting the nozzle\nG1 Z+0.5\nG90\nG1 X5 \n\n
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process = 
print_center = 100,120
raft_air_gap = 0.22
raft_extruder = 1
raft_extra_distance_around_part = 5
raft_fan_speed_percent = 100
raft_layers = 0
raft_print_speed = 40
randomize_start = 0
repair_outlines_extensive_stitching = 0
repair_outlines_keep_open = 0
resolution = 0
resume_gcode = @restore_xyz_position\n@restore_e_position
retract_before_travel = 10
retract_layer_change = 1
retract_length = 6
retract_length_tool_change = 12
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 100
skirt_distance = 3
skirt_height = 1
skirts = 2
slowdown_below_layer_time = 15
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G21\nG90\nM82\nM107\nG28 SC\nG92 X-5\nG92 E0\nG1 F200 E3\nG92 E0\n
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 0
support_material = 0
support_material_angle = 45
support_material_create_internal_support = 1
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_infill_angle = 45
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = honeycomb
support_material_spacing = 3
support_material_speed = 30
support_material_threshold = 45
support_material_xy_distance = 1
support_material_z_distance = 0.15
support_material_z_gap_layers = 1
support_type = LINES
temperature = 200
thin_walls = 1
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 5
travel_speed = 150
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
wipe_shield_distance = 0
wipe_tower_size = 0
z_can_be_negative = 0
z_offset = 0