avoid_crossing_perimeters = 1
bed_shape = rectangular
bed_size = 298,275
bed_temperature = 95
bottom_clip_amount = 0
bottom_solid_layers = 1mm
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1.01
bridge_speed = 25
brim_width = 0
build_height = 240
cancel_gcode =
center_part_on_bed = 1
complete_objects = 0
cool_extruder_lift = 0
cooling = 1
create_raft = 1
default_acceleration = 0
disable_fan_first_layers = 1
end_gcode =  M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed\nM107 ; turn off Extruder Fans\nG28 X0 Y0  ; home X axis Y axis\nG1 Y250 ; kick out bed\nM84     ; disable motors
external_perimeter_speed = 80
external_perimeters_first = 0
extra_perimeters =  
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_count = 1
extruder_offset =  0x0
extruders_share_temperature = 0
extrusion_axis =  E
extrusion_multiplier = 1
extrusion_width = 0.35
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 2.89
fill_angle = 45
fill_density = 0.5
fill_pattern =  line
first_layer_acceleration = 0
first_layer_bed_temperature = 0
first_layer_extrusion_width = 0
first_layer_height = 0.3
first_layer_speed = 0.5
first_layer_temperature = 205
g0 = 0
gap_fill_speed = 40
gcode_arcs = 0
gcode_comments = 0
gcode_flavor =  reprap
gcode_output_type = REPRAP
has_fan = 1
has_heated_bed = 1
has_sd_card_reader = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.5
infill_first = 0
infill_only_where_needed = 0
infill_overlap_perimeter = .06
infill_speed = 115
infill_type = TRIANGLES
layer_gcode =  
layer_height = 0.22
max_fan_speed = 0
min_extrusion_before_retract = .1
min_fan_speed = 0
min_print_speed = 5
min_skirt_length = 0
notes =  
nozzle_diameter = 0.35
only_retract_when_crossing_perimeters =  
ooze_prevention = 0
output_filename_format =  [input_filename_base].gcode
overhangs = 1
pause_gcode =
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.33
perimeter_speed = 100
perimeters = 2
post_process =  
print_center = 149,138
raft_air_gap = .2
raft_extruder = 0
raft_extra_distance_around_part = 5
raft_fan_speed_percent = 100
raft_layers = 0
raft_print_speed = 100%
randomize_start = 0
repair_outlines_extensive_stitching = 0
repair_outlines_keep_open = 0
resolution = 0.01
resume_gcode =
retract_before_travel = 20
retract_layer_change = 1
retract_length = 2
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 25
skirt_distance = 6
skirt_height = 1
skirts = 2
slowdown_below_layer_time = 25
small_perimeter_speed = 60
solid_fill_pattern =  rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0.38
solid_infill_speed = 100
spiral_vase = 0
standby_temperature_delta = -5
start_gcode =  G28 ; home all axes\nM203 X192 Y208 Z3 ; Speed limits to minimize skipped steps when moving really fast courtesy of forum.lulzbot.com user 1013
start_perimeters_at_concave_points = 1
start_perimeters_at_non_overhang = 1
support_material = 1
support_material_angle = 0
support_material_create_internal_support = 1
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_infill_angle = 45
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_pattern =  honeycomb
support_material_spacing = 5
support_material_speed = 60
support_material_threshold = 0
support_material_xy_distance = 0.7
support_material_z_distance = 0.15
support_material_z_gap_layers = 1
support_type = LINES
temperature = 215
thin_walls = 1
threads = 2
toolchange_gcode =  
top_infill_extrusion_width = 0.22
top_solid_infill_speed = 70
top_solid_layers = 1mm
travel_speed = 180
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
wipe_shield_distance = 0
wipe_tower_size = 0
z_can_be_negative = 0
z_offset = 0