diff --git a/StaticData/SliceSettings/Properties.json b/StaticData/SliceSettings/Properties.json
index 03f95244c..f9355a4c6 100644
--- a/StaticData/SliceSettings/Properties.json
+++ b/StaticData/SliceSettings/Properties.json
@@ -535,8 +535,6 @@
 		"RebuildGCodeOnChange": false
 	},
 	{
-		"QuickMenuSettings": [],
-		"SetSettingsOnChange": [],
 		"SlicerConfigName": "has_z_servo",
 		"PresentationName": "Has Z Servo",
 		"HelpText": "The printer has a servo for lowering and raising the z probe.",
@@ -549,8 +547,6 @@
 		"RebuildGCodeOnChange": false
 	},
 	{
-		"QuickMenuSettings": [],
-		"SetSettingsOnChange": [],
 		"SlicerConfigName": "has_hardware_leveling",
 		"PresentationName": "Has Hardware Leveling",
 		"HelpText": "The printer has its own auto bed leveling probe and procedure which can be called using a G29 command during Start G-Code.",
@@ -717,8 +713,6 @@
 		"RebuildGCodeOnChange": false
 	},
 	{
-		"QuickMenuSettings": [],
-		"SetSettingsOnChange": [],
 		"SlicerConfigName": "leveling_manual_positions",
 		"PresentationName": "Leveling Positions",
 		"HelpText": "If set, these positions will be used when running the leveling solution. Leave empty for defaults. Data Format:'X1,Y1:...:Xn,Yn'",
@@ -731,8 +725,6 @@
 		"RebuildGCodeOnChange": false
 	},
 	{
-		"QuickMenuSettings": [],
-		"SetSettingsOnChange": [],
 		"SlicerConfigName": "filament_runout_sensor",
 		"PresentationName": "Has Filament Runout Sensor",
 		"HelpText": "Specifies that the firmware has support for ros_0 endstop reporting on M119. TRIGGERED state defines filament has runout. If runout is detected the printers pause G-Code is run.",
@@ -776,8 +768,6 @@
 		"DefaultValue": "0"
 	},
 	{
-		"QuickMenuSettings": [],
-		"SetSettingsOnChange": [],
 		"SlicerConfigName": "z_probe_xy_offset",
 		"PresentationName": "XY Offset",
 		"HelpText": "The distance the z probe is from the extruder in x and y.",
@@ -790,8 +780,6 @@
 		"DefaultValue": "0,0"
 	},
 	{
-		"QuickMenuSettings": [],
-		"SetSettingsOnChange": [],
 		"SlicerConfigName": "z_probe_samples",
 		"PresentationName": "Number of Samples",
 		"HelpText": "The number of times to sample each probe position (results will be averaged).",
@@ -804,8 +792,6 @@
 		"DefaultValue": "1"
 	},
 	{
-		"QuickMenuSettings": [],
-		"SetSettingsOnChange": [],
 		"SlicerConfigName": "z_servo_depolyed_angle",
 		"PresentationName": "Lower / Deploy",
 		"HelpText": "This is the angle that lowers or deploys the z probe.",
@@ -818,8 +804,6 @@
 		"DefaultValue": "0"
 	},
 	{
-		"QuickMenuSettings": [],
-		"SetSettingsOnChange": [],
 		"SlicerConfigName": "z_servo_retracted_angle",
 		"PresentationName": "Raise / Stow",
 		"HelpText": "This is the angle that raises or stows the z probe.",
@@ -832,8 +816,6 @@
 		"DefaultValue": "0"
 	},
 	{
-		"QuickMenuSettings": [],
-		"SetSettingsOnChange": [],
 		"SlicerConfigName": "layer_gcode",
 		"PresentationName": "Layer Change G-Code",
 		"HelpText": "G-Code to be run after the change in Z height for the next layer.",
@@ -1341,8 +1323,6 @@
 		"DefaultValue": "G28 ; home all axes\\nG1 Z5 F5000 ; lift nozzle"
 	},
 	{
-		"QuickMenuSettings": [],
-		"SetSettingsOnChange": [],
 		"SlicerConfigName": "write_regex",
 		"PresentationName": "Write Filter",
 		"HelpText": "This is a set of regular expressions to apply to lines prior to sending to a printer. They will be applied in the order listed before sending. To return more than one instruction separate them with comma.",
@@ -1354,8 +1334,6 @@
 		"DefaultValue": ""
 	},
 	{
-		"QuickMenuSettings": [],
-		"SetSettingsOnChange": [],
 		"SlicerConfigName": "read_regex",
 		"PresentationName": "Read Filter",
 		"HelpText": "This is a set of regular expressions to apply to lines after they are received from the printer. They will be applied in order to each line received.",