Added updated settings sent from 'Revolution 3D' and '3D Stuffmaker'

StaticData/PrinterSettings/3D Stuffmaker/Evolution/config.ini

@@ -7,9 +7,9 @@ bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_fan_speed = 100
 bridge_flow_ratio = 0.8
-bridge_speed = 18
+bridge_speed = 20
 brim_width = 0.5
-build_height = 205
+build_height = 200
 cancel_gcode = G91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nG1 E-10 F500 ; Retract Extruder\nG90;\nG28 X0;   Home X axis\nG1 Y225 F3000; bring plate to front\nM84;
 center_part_on_bed = 1
 complete_objects = 1
@@ -19,7 +19,7 @@ create_raft = 1
 default_acceleration = 0
 disable_fan_first_layers = 1
 end_gcode = M104 S0 ; turn off temperature\nG91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nG1 E-10 F500 ; Retract Extruder\nG90;\nG28 X0  ; home X axis\nG1 Y225 F3000; bring plate to front\nM84;
-external_perimeter_speed = 60
+external_perimeter_speed = 24
 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 35
@@ -34,7 +34,7 @@ fan_always_on = 0
 fan_below_layer_time = 60
 filament_diameter = 1.74
 fill_angle = 45
-fill_density = 0.2
+fill_density = 0.45
 fill_pattern = rectilinear
 first_layer_acceleration = 0
 first_layer_bed_temperature = 0
@@ -49,6 +49,7 @@ gcode_comments = 1
 gcode_flavor = reprap
 gcode_output_type = REPRAP
 has_fan = 1
+has_hardware_leveling = 0
 has_heated_bed = 0
 has_sd_card_reader = 0
 heat_extruder_before_homing = 1
@@ -59,17 +60,17 @@ infill_extrusion_width = 0
 infill_first = 0
 infill_only_where_needed = 1
 infill_overlap_perimeter = .06
-infill_speed = 60
+infill_speed = 24
 infill_type = LINES
 layer_gcode = 
-layer_height = 0.25
+layer_height = 0.3
 max_fan_speed = 100
 min_extrusion_before_retract = 0.1
 min_fan_speed = 35
-min_print_speed = 10
+min_print_speed = 9
 min_skirt_length = 2
 notes = 
-nozzle_diameter = 0.4
+nozzle_diameter = 0.45
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base].gcode
@@ -78,15 +79,16 @@ pause_gcode = G1 X0 Y0 F3000; home all axes\nM84 S0
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0
-perimeter_speed = 65
-perimeters = 2
+perimeter_speed = 24
+perimeters = 3
 post_process = 
 print_center = 120,130
-raft_air_gap = 0.45
+raft_air_gap = 0.3
+raft_extruder = 0
 raft_extra_distance_around_part = 8
 raft_fan_speed_percent = 100
 raft_layers = 0
-raft_print_speed = 20
+raft_print_speed = 24
 randomize_start = 1
 repair_outlines_extensive_stitching = 1
 repair_outlines_keep_open = 0
@@ -96,14 +98,14 @@ retract_before_travel = 3
 retract_layer_change = 0
 retract_length = 1
 retract_length_tool_change = 10
-retract_lift = 0.0125
+retract_lift = 0.06
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
-retract_speed = 55
+retract_speed = 25
 skirt_distance = 0.7
 skirt_height = 2
 skirts = 3
-slowdown_below_layer_time = 20
+slowdown_below_layer_time = 8
 small_perimeter_speed = 10
 solid_fill_pattern = concentric
 solid_infill_below_area = 70
@@ -120,27 +122,27 @@ support_material_angle = 45
 support_material_create_internal_support = 0
 support_material_enforce_layers = 0
 support_material_extruder = 1
-support_material_extrusion_width = 0
+support_material_extrusion_width = 100%
 support_material_infill_angle = 45
 support_material_interface_extruder = 1
 support_material_interface_layers = 2
 support_material_interface_spacing = 0
 support_material_pattern = honeycomb
 support_material_spacing = 2.5
-support_material_speed = 60
+support_material_speed = 24
 support_material_threshold = 25
 support_material_xy_distance = 0.8
 support_material_z_distance = 0.15
 support_material_z_gap_layers = 4
 support_type = LINES
-temperature = 200
+temperature = 208
 thin_walls = 1
 threads = 2
 toolchange_gcode = 
 top_infill_extrusion_width = 0
 top_solid_infill_speed = 35
-top_solid_layers = 4
-travel_speed = 140
+top_solid_layers = 5
+travel_speed = 95
 use_firmware_retraction = 0
 use_relative_e_distances = 0
 vibration_limit = 0