Made jump start have better default queue, correct on connect gcode and start gcode

Don't crash on close enter share code when not logged in
Fixed jump start pla settings.

StaticData/PrinterSettings/JumpStart/V1/calibration.ini

@@ -1 +1,3 @@
 Calibration - Circle.stl
+Calibration - Box.stl
+MatterControl - Coin.stl

StaticData/PrinterSettings/JumpStart/V1/config.ini

@@ -13,7 +13,7 @@ build_height = 200
 cancel_gcode = G28 X0\n
 center_part_on_bed = 1
 complete_objects = 0
-connect_gcode = 
+connect_gcode = M205 X8\nM201 X1500 Y1500 Z100 E3000\nM204 S0 T1800
 cool_extruder_lift = 1
 print_leveling_solution = 3 Point Plane
 print_leveling_method = Manual
@@ -127,7 +127,7 @@ solid_infill_speed = 60
 solid_shell = 0
 spiral_vase = 0
 standby_temperature_delta = -5
-start_gcode = G28 ; home all axes\nG1 Z10 F5000 ; lift nozzle\nM109 S210 ; set the extruder temp and wait
+start_gcode = G28 ; home all axes\nG1 Z10 F5000 ; lift nozzle
 start_perimeters_at_concave_points = 1
 start_perimeters_at_non_overhang = 1
 support_air_gap = 0.25

StaticData/PrinterSettings/JumpStart/V1/material/PLA.slice

@@ -1,169 +1,2 @@
-avoid_crossing_perimeters = 1
-bed_shape = rectangular
-bed_size = 190,250
-bed_temperature = 0
-bottom_clip_amount = 0
-bottom_solid_layers = 4
-bridge_acceleration = 0
-bridge_fan_speed = 100
-bridge_flow_ratio = 1
-bridge_speed = 40
-brim_width = 3
-build_height = 200
-cancel_gcode = G28 X0\n
-center_part_on_bed = 1
-complete_objects = 0
-connect_gcode = 
-cool_extruder_lift = 1
-print_leveling_solution = 3 Point Plane
-print_leveling_method = Manual
-print_leveling_required_to_print = 1
-manual_probe_paper_width = .1
-cooling = 1
-create_raft = 0
-default_acceleration = 0
-disable_fan_first_layers = 0
-end_gcode = M104 S0 ; turn off temperature\nG1 X10 Y200\nM84     ; disable motors
-external_perimeter_speed = 25
-external_perimeters_first = 0
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extruder_count = 1
-extruder_offset = 0x0
-extruder_wipe_temperature = 0
-extruders_share_temperature = 0
-extrusion_axis = E
-extrusion_multiplier = 1
-extrusion_width = 0
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_diameter = 1.75
-fill_angle = 45
-fill_density = 30%
-fill_pattern = rectilinear
-first_layer_acceleration = 0
-first_layer_bed_temperature = 85
-first_layer_extrusion_width = 125%
-first_layer_height = 0.3
-first_layer_speed = 15
-first_layer_temperature = 230
-g0 = 0
-gap_fill_speed = 30
-gcode_arcs = 0
-gcode_comments = 1
-gcode_flavor = reprap
-gcode_output_type = REPRAP
-has_fan = 0
-has_hardware_leveling = 0
-has_heated_bed = 0
-has_power_control = 0
-has_sd_card_reader = 1
-show_reset_connection = 0
-heat_extruder_before_homing = 1
-infill_acceleration = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_first = 0
-infill_only_where_needed = 1
-infill_overlap_perimeter = 0.2
-infill_speed = 45
-infill_type = TRIANGLES
-layer_gcode = 
-layer_height = 0.2
-layer_to_pause = 
-max_fan_speed = 100
-min_extrusion_before_retract = 0.1
-min_fan_speed = 100
-min_print_speed = 15
-min_skirt_length = 5
-notes = 
-nozzle_diameter = 0.4
-only_retract_when_crossing_perimeters = 0
-ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-pause_gcode = 
-perimeter_acceleration = 0
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-external_perimeter_extrusion_width = 0
-perimeter_speed = 35
-perimeters = 2
-post_process = 
-print_center = 95,125
-raft_air_gap = 0.2
-raft_extruder = 0
-raft_extra_distance_around_part = 3
-raft_fan_speed_percent = 100
-raft_layers = 0
-raft_print_speed = 25
-bed_remove_part_temperature = 0
-randomize_start = 1
-repair_outlines_extensive_stitching = 1
-repair_outlines_keep_open = 1
-resolution = 0
-resume_gcode = 
-retract_before_travel = 10
-retract_layer_change = 1
-retract_length = 3
-retract_length_tool_change = 10
-retract_lift = 0
-retract_restart_extra = 0
-retract_restart_extra_toolchange = 0
-retract_when_changing_islands = 1
-retract_speed = 50
-skirt_distance = 3
-skirt_height = 1
-skirts = 4
-slowdown_below_layer_time = 20
-small_perimeter_speed = 30
-solid_fill_pattern = rectilinear
-solid_infill_below_area = 70
-solid_infill_every_layers = 0
-solid_infill_extrusion_width = 0
-solid_infill_speed = 60
-solid_shell = 0
-spiral_vase = 0
-standby_temperature_delta = -5
-start_gcode = G28 ; home all axes\nG1 Z10 F5000 ; lift nozzle\nM109 S210 ; set the extruder temp and wait
-start_perimeters_at_concave_points = 1
-start_perimeters_at_non_overhang = 1
-support_air_gap = 0.25
-support_material = 0
-support_material_angle = 0
-support_material_percent = 50
-support_material_create_internal_support = 1
-support_material_create_perimeter = 1
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_infill_angle = 45
-support_material_interface_extruder = 1
-support_material_interface_layers = 3
-support_material_interface_spacing = 1
-support_material_pattern = rectilinear
-support_material_spacing = 3
-support_material_speed = 40
-support_material_threshold = 45
-support_material_xy_distance = 1.5
-support_material_z_distance = 0.15
-support_material_z_gap_layers = 4
-support_type = LINES
 temperature = 205
-thin_walls = 1
-threads = 3
-toolchange_gcode = 
-top_infill_extrusion_width = 0
-top_solid_infill_speed = 35
-top_solid_layers = 4
-travel_speed = 150
-use_firmware_retraction = 0
-use_relative_e_distances = 0
-vibration_limit = 0
-wipe = 0
-wipe_shield_distance = 0
-wipe_tower_size = 0
-z_can_be_negative = 0
-z_offset = 0.2
+first_layer_temperature = 205