Added new material and quality presets for Revolution 3d

StaticData/PrinterSettings/Revolution 3D/Infinity/Low-INF3D-SPE.slice

@@ -1,147 +0,0 @@
-avoid_crossing_perimeters = 0
-bed_shape = rectangular
-bed_size = 215,215
-bed_temperature = 50
-bottom_clip_amount = 0
-bottom_solid_layers = 3
-bridge_acceleration = 0
-bridge_fan_speed = 100
-bridge_flow_ratio = 1
-bridge_speed = 20
-brim_width = 0
-build_height = 230
-cancel_gcode = 
-center_part_on_bed = 1
-complete_objects = 0
-cool_extruder_lift = 0
-cooling = 1
-create_raft = 0
-raft_extra_distance_around_part = 5
-raft_air_gap = .2
-default_acceleration = 0
-disable_fan_first_layers = 1
-end_gcode = M104 S0    ;extruder heater off\nM140 S0    ; bed heat off\nG91      ;relative positioning\nG1 E-1 F300  ;retract the filament a bit before lifting the nozzle\nG1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament \nG28 X0 Y0  ;move X/Y to min endstops, so the head is out of the way\nM84         ;steppers off\nG90     ;absolute positioning
-external_perimeter_speed = 60
-external_perimeters_first = 0
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extruder_offset = 0x0
-extrusion_axis = E
-extrusion_multiplier = 1
-extrusion_width = 0
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_diameter = 1.75
-fill_angle = 45
-fill_density = 0.2
-fill_pattern = rectilinear
-first_layer_acceleration = 0
-first_layer_bed_temperature = 70
-first_layer_extrusion_width = 200%
-first_layer_height = 0.3
-first_layer_speed = 35%
-first_layer_temperature = 205
-g0 = 0
-gap_fill_speed = 20
-gcode_arcs = 0
-gcode_comments = 0
-gcode_flavor = reprap
-gcode_output_type = REPRAP
-has_fan = 0
-has_heated_bed = 1
-has_sd_card_reader = 1
-infill_acceleration = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_first = 0
-infill_only_where_needed = 0
-infill_overlap_perimeter = .06
-infill_speed = 60
-infill_type = TRIANGLES
-layer_gcode = 
-layer_height = 0.3
-min_extrusion_before_retract = .1
-max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 10
-min_skirt_length = 5
-notes = 
-nozzle_diameter = 0.35
-only_retract_when_crossing_perimeters = 1
-ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-pause_gcode = 
-perimeter_acceleration = 0
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 60
-perimeters = 2
-post_process = 
-print_center = 133,120
-raft_layers = 0
-randomize_start = 0
-repair_outlines_extensive_stitching = 1
-repair_outlines_keep_open = 1
-repair_overlaps_reverse_orientation = 0
-repair_overlaps_union_all_together = 0
-resolution = 0
-resume_gcode = 
-retract_before_travel = 2
-retract_layer_change = 1
-retract_length = 1
-retract_length_tool_change = 10
-retract_lift = 0
-retract_restart_extra = 0
-retract_restart_extra_toolchange = 0
-retract_speed = 30
-skirt_distance = 6
-skirt_height = 1
-skirts = 1
-slowdown_below_layer_time = 30
-small_perimeter_speed = 30
-solid_fill_pattern = rectilinear
-solid_infill_below_area = 40
-solid_infill_every_layers = 0
-solid_infill_extrusion_width = 0
-solid_infill_speed = 60
-spiral_vase = 0
-standby_temperature_delta = -5
-start_gcode = G90        ;absolute positioning\nG28 X0 Y0  ;move X/Y to min endstops\nG1 F800  Y40  ;move Y 40mm to not hit clip\nM84              ;steppers off\nG28 Z0     ;move Z to min endstops\nG92 E0                  ;zero the extruded length\nG1 F200 E3              ;extrude 10mm of feed stock\nG92 E0                  ;zero the extruded length again\nG1 F7800\nM117      [input_filename_base]    ; what will be displayed
-start_perimeters_at_concave_points = 0
-start_perimeters_at_non_overhang = 0
-support_material = 0
-support_material_angle = 45
-support_material_infill_angle = 45
-support_material_create_internal_support = 0
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 3
-support_material_interface_spacing = 0
-support_material_pattern = honeycomb
-support_material_spacing = 2.5
-support_material_speed = 60
-support_material_threshold = 0
-support_material_xy_distance = 0.7
-support_material_z_distance = 0.15
-support_material_z_gap_layers = 1
-support_type = LINES
-temperature = 220
-thin_walls = 1
-threads = 2
-toolchange_gcode = 
-top_infill_extrusion_width = 0
-top_solid_infill_speed = 50
-top_solid_layers = 3
-travel_speed = 110
-use_firmware_retraction = 0
-use_relative_e_distances = 0
-vibration_limit = 0
-wipe = 0
-wipe_shield_distance = 0
-z_can_be_negative = 0
-z_offset = 0

StaticData/PrinterSettings/Revolution 3D/Infinity/material/ABS.slice

@@ -0,0 +1,3 @@
+filament_diameter = 1.75
+first_layer_bed_temperature = 110
+temperature = 235

StaticData/PrinterSettings/Revolution 3D/Infinity/material/PLA.slice

@@ -0,0 +1,4 @@
+filament_diameter = 1.75
+first_layer_bed_temperature = 50
+temperature = 220
+bed_temperature = 50

StaticData/PrinterSettings/Revolution 3D/Infinity/quality/High.slice

@@ -0,0 +1,4 @@
+layer_height = 0.1
+first_layer_height = 0.3
+perimeters = 3
+fill_density = 0.25

StaticData/PrinterSettings/Revolution 3D/Infinity/quality/Low.slice

@@ -0,0 +1,11 @@
+layer_height = 0.3
+first_layer_height = 0.3
+perimeters = 2
+top_solid_layers = 2
+fill_density = 0.1
+fill_pattern = rectilinear
+perimeter_speed = 70
+top_solid_infill_speed = 65
+infill_speed = 80
+external_perimeter_speed = 70
+bottom_solid_layers = 2

StaticData/PrinterSettings/Revolution 3D/Infinity/quality/Medium.slice

@@ -0,0 +1,3 @@
+layer_height = 0.2
+first_layer_height = 0.3
+fill_density = 0.25

StaticData/PrinterSettings/Revolution 3D/Infinity/setup.ini

@@ -0,0 +1,2 @@
+baud_rate = 250000
+default_material_presets = ABS