diff --git a/StaticData/PrinterSettings/Airwolf 3D/HD-R/config.ini b/StaticData/PrinterSettings/Airwolf 3D/HD-R/config.ini
index 34e58893d..1844738fa 100644
--- a/StaticData/PrinterSettings/Airwolf 3D/HD-R/config.ini	
+++ b/StaticData/PrinterSettings/Airwolf 3D/HD-R/config.ini	
@@ -43,6 +43,7 @@ gap_fill_speed = 30
 gcode_arcs = 0
 gcode_comments = 0
 gcode_flavor = reprap
+has_hardware_leveling = 1
 has_sd_card_reader = 1
 infill_acceleration = 0
 infill_every_layers = 1
diff --git a/StaticData/PrinterSettings/Airwolf 3D/HD/config.ini b/StaticData/PrinterSettings/Airwolf 3D/HD/config.ini
index 36cb94a64..d971e8172 100644
--- a/StaticData/PrinterSettings/Airwolf 3D/HD/config.ini	
+++ b/StaticData/PrinterSettings/Airwolf 3D/HD/config.ini	
@@ -41,6 +41,7 @@ gap_fill_speed = 30
 gcode_arcs = 0
 gcode_comments = 0
 gcode_flavor = reprap
+has_hardware_leveling = 1
 has_sd_card_reader = 1
 infill_acceleration = 0
 infill_every_layers = 1
diff --git a/StaticData/PrinterSettings/Airwolf 3D/HD2x/config.ini b/StaticData/PrinterSettings/Airwolf 3D/HD2x/config.ini
index 34e58893d..1844738fa 100644
--- a/StaticData/PrinterSettings/Airwolf 3D/HD2x/config.ini	
+++ b/StaticData/PrinterSettings/Airwolf 3D/HD2x/config.ini	
@@ -43,6 +43,7 @@ gap_fill_speed = 30
 gcode_arcs = 0
 gcode_comments = 0
 gcode_flavor = reprap
+has_hardware_leveling = 1
 has_sd_card_reader = 1
 infill_acceleration = 0
 infill_every_layers = 1
diff --git a/StaticData/PrinterSettings/Airwolf 3D/HDL/config.ini b/StaticData/PrinterSettings/Airwolf 3D/HDL/config.ini
index d679048c9..ff7d34765 100644
--- a/StaticData/PrinterSettings/Airwolf 3D/HDL/config.ini	
+++ b/StaticData/PrinterSettings/Airwolf 3D/HDL/config.ini	
@@ -42,6 +42,7 @@ gcode_arcs = 0
 gcode_comments = 0
 gcode_flavor = reprap
 has_fan = 1
+has_hardware_leveling = 1
 has_heated_bed = 0
 has_sd_card_reader = 1
 infill_acceleration = 0
diff --git a/StaticData/PrinterSettings/Airwolf 3D/HDx/config.ini b/StaticData/PrinterSettings/Airwolf 3D/HDx/config.ini
index 36cb94a64..d971e8172 100644
--- a/StaticData/PrinterSettings/Airwolf 3D/HDx/config.ini	
+++ b/StaticData/PrinterSettings/Airwolf 3D/HDx/config.ini	
@@ -41,6 +41,7 @@ gap_fill_speed = 30
 gcode_arcs = 0
 gcode_comments = 0
 gcode_flavor = reprap
+has_hardware_leveling = 1
 has_sd_card_reader = 1
 infill_acceleration = 0
 infill_every_layers = 1