Put in TAZ 5 settings

StaticData/PrinterSettings/Lulzbot/Mini/quality/Coarse.slice

@@ -1 +0,0 @@
-layer_height = 0.3

StaticData/PrinterSettings/Lulzbot/Mini/quality/Fine.slice

@@ -1 +0,0 @@
-layer_height = 0.1

StaticData/PrinterSettings/Lulzbot/Mini/quality/Standard.slice

@@ -1 +0,0 @@
-layer_height = 0.2

StaticData/PrinterSettings/Lulzbot/TAZ 4/config.ini

@@ -38,7 +38,7 @@ fill_density = 0.5
 fill_pattern =  line
 first_layer_acceleration = 0
 first_layer_bed_temperature = 0
-first_layer_extrusion_width = 0.5
+first_layer_extrusion_width = 0
 first_layer_height = 0.3
 first_layer_speed = 0.5
 first_layer_temperature = 205
@@ -88,8 +88,8 @@ raft_fan_speed_percent = 100
 raft_layers = 0
 raft_print_speed = 100%
 randomize_start = 0
-repair_outlines_extensive_stitching = 1
-repair_outlines_keep_open = 1
+repair_outlines_extensive_stitching = 0
+repair_outlines_keep_open = 0
 resolution = 0.01
 resume_gcode =
 retract_before_travel = 20

StaticData/PrinterSettings/Lulzbot/TAZ 4/material/PLA.slice

@@ -21,5 +21,5 @@ retract_speed = 30
 small_perimeter_speed = 30
 solid_infill_below_area = 90
 solid_infill_speed = 65
-temperature = 185
+temperature = 190
 top_solid_layers = 4

StaticData/PrinterSettings/Lulzbot/TAZ 4/quality/Coarse.slice

@@ -1 +0,0 @@
-layer_height = 0.3

StaticData/PrinterSettings/Lulzbot/TAZ 4/quality/Fine.slice

@@ -1 +0,0 @@
-layer_height = 0.1

StaticData/PrinterSettings/Lulzbot/TAZ 4/quality/Standard.slice

@@ -1 +0,0 @@
-layer_height = 0.2

StaticData/PrinterSettings/Lulzbot/TAZ 5/config.ini

@@ -0,0 +1,154 @@
+avoid_crossing_perimeters = 1
+bed_shape = rectangular
+bed_size = 300,300
+bed_temperature = 60
+bottom_clip_amount = 0
+bottom_solid_layers = 3
+bridge_acceleration = 2000
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 72
+brim_width = 0
+build_height = 240
+cancel_gcode = 
+center_part_on_bed = 1
+complete_objects = 0
+cool_extruder_lift = 0
+cooling = 1
+create_raft = 0
+default_acceleration = 2000
+disable_fan_first_layers = 2
+end_gcode = M400      ;   \nM104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200\nG28 X0  ; home X axis\nM84     ; disable motors
+external_perimeter_speed = 45
+external_perimeters_first = 
+extra_perimeters = 
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_count = 1
+extruder_offset = 0x0
+extruders_share_temperature = 0
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width = .42
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_diameter = 2.89
+fill_angle = 45
+fill_density = 30%
+fill_pattern = line
+first_layer_acceleration = 2000
+first_layer_bed_temperature = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.2
+first_layer_speed = 75%
+first_layer_temperature = 0
+g0 = 0
+gap_fill_speed = 55
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+gcode_output_type = REPRAP
+has_fan = 1
+has_hardware_leveling = 0
+has_heated_bed = 1
+has_sd_card_reader = 1
+show_reset_connection = 0
+heat_extruder_before_homing = 0
+infill_acceleration = 2000
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = .68
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap_perimeter = .06
+infill_speed = 80
+infill_type = TRIANGLES
+layer_gcode = 
+layer_height = 0.2
+max_fan_speed = 90
+min_extrusion_before_retract = .1
+min_fan_speed = 35
+min_print_speed = 25
+min_skirt_length = 5
+notes = 
+nozzle_diameter = 0.35
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+pause_gcode = 
+perimeter_acceleration = 1200
+perimeter_extruder = 1
+perimeter_extrusion_width = .38
+perimeter_speed = 75
+perimeters = 2
+post_process = 
+print_center = 140,140
+raft_air_gap = .2
+raft_extruder = 0
+raft_extra_distance_around_part = 5
+raft_fan_speed_percent = 100
+raft_layers = 0
+raft_print_speed = 100%
+randomize_start = 
+repair_outlines_extensive_stitching = 0
+repair_outlines_keep_open = 0
+resolution = 0
+resume_gcode = 
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 1.9
+retract_length_tool_change = 10
+retract_lift = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 25
+small_perimeter_speed = 50
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 90
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = .5
+solid_infill_speed = 75
+spiral_vase = 0
+standby_temperature_delta = -5
+start_gcode = G28 ; home all axes
+start_perimeters_at_concave_points = 1
+start_perimeters_at_non_overhang = 1
+support_material = 0
+support_material_angle = 0
+support_material_create_internal_support = 1
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_infill_angle = 45
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 2.5
+support_material_speed = 60
+support_material_threshold = 45
+support_material_xy_distance = 0.7
+support_material_z_distance = 0.15
+support_material_z_gap_layers = 1
+support_type = LINES
+temperature = 205
+thin_walls = 1
+threads = 2
+toolchange_gcode = 
+top_infill_extrusion_width = .4
+top_solid_infill_speed = 60
+top_solid_layers = 3
+travel_speed = 160
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+wipe_shield_distance = 0
+wipe_tower_size = 0
+z_can_be_negative = 0
+z_offset = 0

StaticData/PrinterSettings/Lulzbot/TAZ 5/material/ABS.slice

@@ -0,0 +1,11 @@
+bed_temperature = 85
+bridge_fan_speed = 100
+bridge_speed = 25
+first_layer_bed_temperature = 85
+first_layer_temperature = 235
+max_fan_speed = 0
+min_fan_speed = 0
+retract_length = 1.9
+retract_length_toolchange = 3
+temperature = 230
+top_solid_layers = 4

StaticData/PrinterSettings/Lulzbot/TAZ 5/material/HIPS.slice

@@ -0,0 +1,11 @@
+bed_temperature = 85
+bridge_flow_ratio = 1.3
+external_perimeter_speed = 60
+extra_perimeters = 1
+first_layer_bed_temperature = 85
+first_layer_speed = 0.2
+first_layer_temperature = 235
+infill_speed = 95
+small_perimeter_speed = 48
+solid_infill_speed = 80
+temperature = 230

StaticData/PrinterSettings/Lulzbot/TAZ 5/material/LAYBRICK.slice

@@ -0,0 +1,20 @@
+bed_temperature = 50
+bridge_flow_ratio = 1.15
+bridge_speed = 25
+external_perimeter_speed = 20
+extra_perimeters = 1
+first_layer_bed_temperature = 50
+first_layer_speed = 0.75
+first_layer_temperature = 185
+gap_fill_speed = 45
+infill_speed = 56
+min_print_speed = 25
+resolution = 0
+retract_length = 1.9
+retract_length_toolchange = 3
+retract_speed = 30
+small_perimeter_speed = 23
+solid_infill_below_area = 90
+solid_infill_speed = 52
+temperature = 185
+top_solid_layers = 5

StaticData/PrinterSettings/Lulzbot/TAZ 5/material/LAYWOOD.slice

@@ -0,0 +1,21 @@
+bed_temperature = 50
+bridge_flow_ratio = 1.15
+bridge_speed = 25
+external_perimeter_speed = 20
+extra_perimeters = 1
+first_layer_bed_temperature = 50
+first_layer_speed = 0.75
+first_layer_temperature = 180
+gap_fill_speed = 45
+infill_speed = 56
+min_print_speed = 25
+raft_layers = 3
+resolution = 0
+retract_length = 3.5
+retract_length_toolchange = 3
+retract_speed = 30
+small_perimeter_speed = 23
+solid_infill_below_area = 90
+solid_infill_speed = 52
+temperature = 180
+top_solid_layers = 5

StaticData/PrinterSettings/Lulzbot/TAZ 5/material/NINJAFLEX.slice

@@ -0,0 +1,18 @@
+bed_temperature = 35
+bridge_flow_ratio = 1
+bridge_speed = 30
+external_perimeter_speed = 30
+extra_perimeters = 1
+first_layer_bed_temperature = 35
+first_layer_speed = 30
+first_layer_temperature = 230
+gap_fill_speed = 30
+infill_speed = 30
+min_print_speed = 10
+perimeters = 3
+resolution = 0
+retract_length = 3
+retract_speed = 20
+small_perimeter_speed = 30
+solid_infill_speed = 30
+temperature = 230

StaticData/PrinterSettings/Lulzbot/TAZ 5/material/NYLON615.slice

@@ -0,0 +1,21 @@
+bed_temperature = 85
+bottom_solid_layers = 4
+bridge_flow_ratio = 1.12
+bridge_speed = 30
+brim_width = 3
+external_perimeter_speed = 0.75
+extra_perimeters = 1
+first_layer_bed_temperature = 85
+first_layer_speed = 0.3
+first_layer_temperature = 235
+gap_fill_speed = 20
+infill_speed = 40
+min_print_speed = 25
+perimeters = 5
+retract_length = 4.5
+retract_length_toolchange = 3
+small_perimeter_speed = 28
+solid_infill_below_area = 90
+solid_infill_speed = 35
+temperature = 235
+top_solid_layers = 4

StaticData/PrinterSettings/Lulzbot/TAZ 5/material/NYLON645.slice

@@ -0,0 +1,21 @@
+bed_temperature = 85
+bottom_solid_layers = 4
+bridge_flow_ratio = 1.12
+bridge_speed = 30
+brim_width = 3
+external_perimeter_speed = 0.75
+extra_perimeters = 1
+first_layer_speed = 0.3
+first_layer_bed_temperature = 85
+first_layer_temperature = 235
+gap_fill_speed = 20
+infill_speed = 40
+min_print_speed = 25
+perimeters = 5
+retract_length = 4.5
+retract_length_toolchange = 3
+small_perimeter_speed = 28
+solid_infill_below_area = 90
+solid_infill_speed = 35
+temperature = 235
+top_solid_layers = 4

StaticData/PrinterSettings/Lulzbot/TAZ 5/material/NYLONBRIDGE.slice

@@ -0,0 +1,18 @@
+bed_temperature = 85
+bottom_solid_layers = 2
+bridge_flow_ratio = 1.3
+bridge_speed = 50
+brim_width = 3
+external_perimeter_speed = 0.75
+first_layer_bed_temperature = 85
+first_layer_speed = 0.3
+first_layer_temperature = 235
+infill_speed = 100
+min_print_speed = 25
+resolution = 0
+retract_length = 1.9
+retract_length_toolchange = 3
+small_perimeter_speed = 65
+solid_infill_below_area = 90
+solid_infill_speed = 75
+temperature = 235

StaticData/PrinterSettings/Lulzbot/TAZ 5/material/PLA.slice

@@ -0,0 +1,25 @@
+bed_temperature = 50
+bridge_fan_speed = 100
+bridge_flow_ratio = 1.15
+bridge_speed = 25
+disable_fan_first_layers = 2
+external_perimeter_speed = 25
+extra_perimeters = 1
+fan_always_on = 1
+first_layer_bed_temperature = 50
+first_layer_speed = 0.75
+first_layer_temperature = 205
+gap_fill_speed = 45
+infill_speed = 70
+max_fan_speed = 90
+min_fan_speed = 35
+min_print_speed = 25
+resolution = 0
+retract_length = 1.9
+retract_length_toolchange = 3
+retract_speed = 30
+small_perimeter_speed = 30
+solid_infill_below_area = 90
+solid_infill_speed = 65
+temperature = 205
+top_solid_layers = 4

StaticData/PrinterSettings/Lulzbot/TAZ 5/material/T-GLASE.slice

@@ -0,0 +1,16 @@
+bed_temperature = 50
+bridge_flow_ratio = 1.3
+bridge_speed = 45
+external_perimeter_speed = 0.75  
+first_layer_bed_temperature = 50
+first_layer_speed = 0.75
+first_layer_temperature = 230
+gap_fill_speed = 30
+infill_speed = 20
+min_print_speed = 25
+resolution = 0
+retract_length_toolchange = 3
+small_perimeter_speed = 12.5
+solid_infill_below_area = 90
+solid_infill_speed = 18
+temperature = 230

StaticData/PrinterSettings/Lulzbot/TAZ 5/setup.ini

@@ -0,0 +1,3 @@
+baud_rate = 115200
+default_material_presets = ABS
+windows_driver = MHSerial.inf

StaticData/PrinterSettings/Lulzbot/TAZ/quality/Coarse.slice

@@ -1 +0,0 @@
-layer_height = 0.3

StaticData/PrinterSettings/Lulzbot/TAZ/quality/Fine.slice

@@ -1 +0,0 @@
-layer_height = 0.1

StaticData/PrinterSettings/Lulzbot/TAZ/quality/Standard.slice

@@ -1 +0,0 @@
-layer_height = 0.2