Move MatterControl source code into a subdirectory

original/StaticData/SliceSettings/Layouts.txt

@@ -0,0 +1,232 @@
+Advanced
+  General
+    General
+      layer_height
+      first_layer_height
+      perimeters
+      top_solid_layers
+      bottom_solid_layers
+      fill_density
+      infill_type
+    Layers / Surface
+      avoid_crossing_perimeters
+      avoid_crossing_max_ratio
+      external_perimeters_first
+      perimeter_start_end_overlap
+      merge_overlapping_lines
+      expand_thin_walls
+      coast_at_end_distance
+    Infill
+      fill_angle
+      infill_overlap_perimeter
+      fill_thin_gaps
+    Extruder Change
+      wipe_shield_distance
+      wipe_tower_size
+  Speed
+    Laser Speed
+      laser_speed_025
+      laser_speed_100
+    Infill Speeds
+      first_layer_speed
+      infill_speed
+      top_solid_infill_speed
+      raft_print_speed
+    Perimeter Speeds
+      perimeter_speed
+      external_perimeter_speed
+      perimeter_acceleration
+      default_acceleration
+    Other Speeds
+      support_material_speed
+      interface_layer_speed
+      air_gap_speed
+      bridge_speed
+      travel_speed
+      number_of_first_layers
+      bridge_over_infill
+      t1_extrusion_move_speed_multiplier
+    Cooling
+      slowdown_below_layer_time
+      min_print_speed
+  Adhesion
+    Skirt
+      create_skirt
+      skirts
+      skirt_distance
+      min_skirt_length
+    Raft
+      create_raft
+      raft_extra_distance_around_part
+      raft_air_gap
+      raft_extruder
+    Brim
+      create_brim
+      brims
+  Support
+    Support
+      create_per_layer_support
+      create_per_layer_internal_support
+      support_percent
+      support_grab_distance
+      support_material_create_perimeter
+      support_material_interface_layers
+      support_material_xy_distance
+      support_air_gap
+      support_type
+      support_material_spacing
+      support_material_infill_angle
+      support_material_extruder
+      support_material_interface_extruder
+  Filament
+    Filament
+      filament_diameter
+      filament_density
+      filament_cost
+      temperature
+      temperature1
+      temperature2
+      temperature3
+      bed_temperature
+      inactive_cool_down
+      seconds_to_reheat
+    Fan
+      min_fan_speed_layer_time
+      max_fan_speed_layer_time
+      min_fan_speed
+      max_fan_speed
+      bridge_fan_speed
+      disable_fan_first_layers
+      min_fan_speed_absolute
+    Retraction
+      retract_length
+      retract_restart_extra
+      retract_restart_extra_time_to_apply
+      retract_speed
+      retract_lift
+      retract_before_travel
+      retract_before_travel_avoid
+      retract_when_changing_islands
+      min_extrusion_before_retract
+      wipe
+      retract_length_tool_change
+      retract_restart_extra_toolchange
+    Advanced
+      extruder_wipe_temperature
+      bed_remove_part_temperature
+      extrusion_multiplier
+      first_layer_extrusion_width
+      external_perimeter_extrusion_width
+Printer
+  General
+    General
+      make
+      model
+      auto_connect
+      baud_rate
+      com_port
+      selector_ip_address
+      ip_address
+      ip_port
+    Bed
+      bed_size
+      print_center
+      build_height
+      bed_shape
+    Extruders
+      extruder_count
+      nozzle_diameter
+      t0_inset
+      t1_inset
+      extruders_share_temperature
+      extruder_offset
+  Features
+    Leveling
+      print_leveling_solution
+      probe_paper_width
+      leveling_sample_points
+      probe_offset_sample_point
+      print_leveling_required_to_print
+    Print Recovery
+      recover_is_enabled
+      recover_first_layer_speed
+      recover_position_before_z_home
+    Probe
+      print_leveling_probe_start
+      use_z_probe
+      validate_leveling
+      validation_threshold
+      z_probe_samples
+      probe_offset
+      z_servo_depolyed_angle
+      z_servo_retracted_angle
+    Behavior
+      slice_engine
+      heat_extruder_before_homing
+      auto_release_motors
+      validate_layer_height
+      emulate_endstops
+      send_with_checksum
+      reset_long_extrusion
+      output_only_first_layer
+      g0
+      progress_reporting
+      include_firmware_updater
+      backup_firmware_before_update
+    Diagnostics
+      report_runout_sensor_data
+    Hardware
+      firmware_type
+      show_reset_connection
+      z_homes_to_max
+      has_fan
+      has_fan_per_extruder
+      has_hardware_leveling
+      has_heated_bed
+      has_sd_card_reader
+      has_power_control
+      filament_runout_sensor
+      runout_sensor_check_distance
+      runout_sensor_trigger_ratio
+      has_z_probe
+      has_z_servo
+      has_c_axis
+      enable_network_printing
+      enable_sailfish_communication
+      sla_printer
+      max_acceleration
+      max_velocity
+      jerk_velocity
+      print_time_estimate_multiplier
+      load_filament_length
+      unload_filament_length
+      load_filament_speed
+    Printer Help
+      trim_filament_markdown
+      insert_filament_markdown2
+      running_clean_markdown2
+      insert_filament_1_markdown
+      running_clean_1_markdown
+      created_date
+  G-Code
+    Printer Control
+      start_gcode
+      end_gcode
+      layer_gcode
+      connect_gcode
+    User Control
+      cancel_gcode
+      pause_gcode
+      resume_gcode
+    Multi-Extruder
+      before_toolchange_gcode
+      toolchange_gcode
+      before_toolchange_gcode_1
+      toolchange_gcode_1
+      before_toolchange_gcode_2
+      toolchange_gcode_2
+      before_toolchange_gcode_3
+      toolchange_gcode_3
+    Filters
+      write_regex
+      read_regex