Merge pull request #572 from gregory-diaz/1.5.1
Added requested printer profile changes from Me3D
This commit is contained in:
Lars Brubaker
commit
6e89887203
1 changed files with 37 additions and 24 deletions
|
|
@ -3,6 +3,7 @@ bed_shape = rectangular
|
|||
bed_size = 200,220
|
||||
bed_temperature = 0
|
||||
bottom_clip_amount = 0
|
||||
bottom_solid_layers = 4
|
||||
bridge_acceleration = 0
|
||||
bridge_fan_speed = 100
|
||||
bridge_flow_ratio = 1
|
||||
|
|
@ -14,6 +15,10 @@ center_part_on_bed = 1
|
|||
complete_objects = 0
|
||||
connect_gcode =
|
||||
cool_extruder_lift = 0
|
||||
print_leveling_solution = 3 Point Plane
|
||||
print_leveling_method = Manual
|
||||
print_leveling_required_to_print = 0
|
||||
manual_probe_paper_width = .1
|
||||
cooling = 1
|
||||
create_raft = 0
|
||||
default_acceleration = 0
|
||||
|
|
@ -35,16 +40,17 @@ fan_always_on = 0
|
|||
fan_below_layer_time = 60
|
||||
filament_diameter = 1.75
|
||||
fill_angle = 45
|
||||
fill_density = 20%
|
||||
fill_pattern = honeycomb
|
||||
fill_density = 15%
|
||||
fill_pattern = rectilinear
|
||||
first_layer_acceleration = 0
|
||||
first_layer_bed_temperature = 0
|
||||
first_layer_extrusion_width = 0
|
||||
first_layer_height = 0.2
|
||||
first_layer_speed = 20
|
||||
first_layer_temperature = 220
|
||||
first_layer_temperature = 210
|
||||
g0 = 0
|
||||
gap_fill_speed = 20
|
||||
gcode_arcs = 1
|
||||
gcode_arcs = 0
|
||||
gcode_comments = 0
|
||||
gcode_flavor = reprap
|
||||
gcode_output_type = REPRAP
|
||||
|
|
@ -62,14 +68,15 @@ infill_extrusion_width = 0
|
|||
infill_first = 0
|
||||
infill_only_where_needed = 0
|
||||
infill_overlap_perimeter = 0.05
|
||||
infill_speed = 100
|
||||
infill_speed = 60
|
||||
infill_type = GRID
|
||||
layer_gcode =
|
||||
layer_height = 0.1
|
||||
max_fan_speed = 100
|
||||
min_extrusion_before_retract = 0
|
||||
min_fan_speed = 80
|
||||
min_print_speed = 10
|
||||
layer_gcode = ; LAYER:[layer_num]
|
||||
layer_height = 0.2
|
||||
layer_to_pause =
|
||||
max_fan_speed = 80
|
||||
min_extrusion_before_retract = 0.005
|
||||
min_fan_speed = 60
|
||||
min_print_speed = 3
|
||||
min_skirt_length = 1
|
||||
notes =
|
||||
nozzle_diameter = 0.4
|
||||
|
|
@ -81,7 +88,8 @@ pause_gcode = G91;\nG1 F250 Z10 X10 E-16; Retract filament from barrel\nG90;\nM1
|
|||
perimeter_acceleration = 0
|
||||
perimeter_extruder = 1
|
||||
perimeter_extrusion_width = 0
|
||||
perimeter_speed = 100
|
||||
external_perimeter_extrusion_width = 100%
|
||||
perimeter_speed = 80
|
||||
perimeters = 2
|
||||
post_process =
|
||||
print_center = 100,110
|
||||
|
|
@ -97,13 +105,14 @@ repair_outlines_extensive_stitching = 1
|
|||
repair_outlines_keep_open = 1
|
||||
resolution = 0
|
||||
resume_gcode = M117 Print resumed\nM109 S[temperature]; // Set print temperature \nG91;\nG1 F250 Z-10 X-10 E16; Prime filament filament from barrel\nG90;
|
||||
retract_before_travel = 0.5
|
||||
retract_layer_change = 1
|
||||
retract_length = 2
|
||||
retract_before_travel = 0.8
|
||||
retract_layer_change = 0
|
||||
retract_length = 2.5
|
||||
retract_length_tool_change = 10
|
||||
retract_lift = 0
|
||||
retract_lift = 1
|
||||
retract_restart_extra = 0
|
||||
retract_restart_extra_toolchange = 0
|
||||
retract_when_changing_islands = 1
|
||||
retract_speed = 50
|
||||
skirt_distance = 3
|
||||
skirt_height = 1
|
||||
|
|
@ -111,18 +120,22 @@ skirts = 1
|
|||
slowdown_below_layer_time = 8
|
||||
small_perimeter_speed = 30
|
||||
solid_fill_pattern = rectilinear
|
||||
solid_infill_below_area = 70
|
||||
solid_infill_below_area = 5
|
||||
solid_infill_every_layers = 0
|
||||
solid_infill_extrusion_width = 0
|
||||
solid_infill_speed = 60
|
||||
solid_shell = 0
|
||||
spiral_vase = 0
|
||||
standby_temperature_delta = -5
|
||||
start_gcode = ;Me3D - MC1.3 startup sequence - Me2 (G5,G6,G7) Build 07/15\n;Remove the ";" to activate any line\n;MAKE SURE YOU KNOW WHAT EACH LINE DOES BEFORE YOU CHANGE IT!!! The Me2 is 100% hackable and so has limited physical protection from errors in the g-code\n M104 S[temperature] ; // Start heater and continue g-code\nG21 ; // set units to millimeters\n M201 X9000 Y9000; // max accel print\nM202 X9000 Y9000; // max accel travel\n M205 X15; // max xyjerk mm/s\nG91; // Relative position\nG1 Z10; // clear bed\nG90 ; // ABS position\nG28; // home axes\nG29; // perform auto levelling at three corners\nM82 ; // use absolute distances for extrusion\nG1 Z15 F4000; // Raise Z axis clear\nG1 X-5 F4000; // Move to X axis zero\nG1 Y5 F4000;\nG92 E0; // zero the extruded length\nM109 S[temperature]; // Set print temperature and wait\nG1 F100 E19; // extrude feed stock to prime hotend barrel and purge\n; //Create purge line\n G1 Z[z_offset] F1000; // z_offset variable only available in 1.2.3 and above\nG91; // Relative motion \nG1 Z0.3;\nG1 X10 Y1 F1000; // Change this value to move the position of the line on the bed\nG1 X120 E20;\nG1 Y1;\nG1 X-100 E16.5;\nG1 X-20 E2;\nG1 X10 Y-3 F500;\nG1 Y5 F4000;\nG92 E0;\nG90;\nG92 E0; // zero the extruded length again\nM117 OK...let's print
|
||||
start_gcode = ;Me3D - MC1.5 startup sequence - Me2 (G5,G6,G7) Build 07/15\n;Remove the ";" to activate any line\n;MAKE SURE YOU KNOW WHAT EACH LINE DOES BEFORE YOU CHANGE IT!!! The Me2 is 100% hackable and so has limited physical protection from errors in the g-code\nM104 S[first_layer_temperature] ; // Start heater and continue g-code\nG21 ; // set units to millimeters\nM201 X5000 Y5000; // max accel print\nM202 X5000 Y5000; // max accel travel\nM205 X15; // max xyjerk mm/s\nG91; // Relative position\nG1 Z10; // clear bed \nG90 ; // ABS position\nG28; // home axes\nG29; // perform auto levelling at three corners\nM82 ; // use absolute distances for extrusion\nG1 Z15 F4000; // Raise Z axis clear\nG1 X-5 F4000; // Move to X axis zero\nG1 Y5 F4000;\nG92 E0; // zero the extruded length\nM109 S[first_layer_temperature]; // Set print temperature and wait\nG1 F100 E19; // extrude feed stock to prime hotend barrel and purge\n; //Create purge line\nG1 Z[z_offset] F1000; // z_offset variable only available in 1.2.3 and above\nG91; // Relative motion \nG1 Z0.3;\nG1 X10 Y1 F1000; // Change this value to move the position of the line on the bed\nG1 X120 E20;\nG1 Y1;\nG1 X-100 E16.5;\nG1 X-20 E2;\nG1 X10 Y-3 F500;\nG1 Y5 F4000;\nG92 E0;\nG90;\nG92 E0; // zero the extruded length again\nM117 OK...let's print;
|
||||
start_perimeters_at_concave_points = 0
|
||||
start_perimeters_at_non_overhang = 0
|
||||
support_material = 0
|
||||
support_air_gap = .3
|
||||
support_material = 1
|
||||
support_material_angle = 45
|
||||
support_material_percent = 10
|
||||
support_material_create_internal_support = 0
|
||||
support_material_create_perimeter = 1
|
||||
support_material_enforce_layers = 0
|
||||
support_material_extruder = 1
|
||||
support_material_extrusion_width = 0
|
||||
|
|
@ -130,19 +143,19 @@ support_material_infill_angle = 45
|
|||
support_material_interface_extruder = 1
|
||||
support_material_interface_layers = 0
|
||||
support_material_interface_spacing = 0
|
||||
support_material_pattern = honeycomb
|
||||
support_material_spacing = 2
|
||||
support_material_pattern = rectilinear
|
||||
support_material_spacing = 2.5
|
||||
support_material_speed = 100
|
||||
support_material_threshold = 19
|
||||
support_material_xy_distance = 1
|
||||
support_material_z_distance = 0.15
|
||||
support_material_z_gap_layers = 3
|
||||
support_type = LINES
|
||||
temperature = 205
|
||||
temperature = 217
|
||||
thin_walls = 1
|
||||
threads = 2
|
||||
toolchange_gcode =
|
||||
top_infill_extrusion_width = 0
|
||||
top_infill_extrusion_width = 90%
|
||||
top_solid_infill_speed = 50
|
||||
top_solid_layers = 4
|
||||
travel_speed = 120
|
||||
|
|
@ -153,4 +166,4 @@ wipe = 0
|
|||
wipe_shield_distance = 0
|
||||
wipe_tower_size = 0
|
||||
z_can_be_negative = 0
|
||||
z_offset = 25
|
||||
z_offset = 25
|
||||
Loading…
Add table
Add a link
Reference in a new issue