Merge pull request #577 from rytz/master

Adding config.ini and calibration.ini to Ultimaker 2+ and 2 Extended+

StaticData/PrinterSettings/Ultimaker/2 Extended+/calibration.ini

@@ -0,0 +1 @@
+Calibration - Circle.stl

StaticData/PrinterSettings/Ultimaker/2 Extended+/material/ABS.slice

@@ -0,0 +1,6 @@
+temperature = 260
+bed_temperature = 90
+max_fan_speed = 50
+extrusion_multiplier = 1
+min_fan_speed = 50
+bridge_fan_speed = 50

StaticData/PrinterSettings/Ultimaker/2 Extended+/material/PET.slice

@@ -0,0 +1,6 @@
+temperature = 250
+bed_temperature = 60
+max_fan_speed = 50
+extrusion_multiplier = 1
+min_fan_speed = 50
+bridge_fan_speed = 50

StaticData/PrinterSettings/Ultimaker/2 Extended+/material/PLA.slice

@@ -0,0 +1,6 @@
+temperature = 210
+bed_temperature = 60
+max_fan_speed = 100
+extrusion_multiplier = 1
+min_fan_speed = 100
+bridge_fan_speed = 100

StaticData/PrinterSettings/Ultimaker/2 Extended+/quality/Fast.slice

@@ -0,0 +1,6 @@
+layer_height = 0.15
+fill_density = 0.1
+first_layer_speed = 30
+infill_speed = 100
+external_perimeter_speed = 40
+perimeter_speed = 80

StaticData/PrinterSettings/Ultimaker/2 Extended+/quality/High.slice

@@ -0,0 +1,6 @@
+layer_height = 0.06
+fill_density = 0.2
+first_layer_speed = 20
+infill_speed = 80
+external_perimeter_speed = 30
+perimeter_speed = 60

StaticData/PrinterSettings/Ultimaker/2 Extended+/quality/Normal.slice

@@ -0,0 +1,6 @@
+layer_height = 0.1
+fill_density = 0.2
+first_layer_speed = 20
+infill_speed = 80
+external_perimeter_speed = 30
+perimeter_speed = 60

StaticData/PrinterSettings/Ultimaker/2 Extended+/quality/Ulti.slice

@@ -0,0 +1,6 @@
+layer_height = 0.04
+fill_density = 0.2
+first_layer_speed = 20
+infill_speed = 80
+external_perimeter_speed = 30
+perimeter_speed = 60

StaticData/PrinterSettings/Ultimaker/2 Extended/material/ABS.slice

@@ -0,0 +1,6 @@
+temperature = 260
+bed_temperature = 90
+max_fan_speed = 50
+extrusion_multiplier = 1
+min_fan_speed = 50
+bridge_fan_speed = 50

StaticData/PrinterSettings/Ultimaker/2 Extended/material/PET.slice

@@ -0,0 +1,6 @@
+temperature = 250
+bed_temperature = 60
+max_fan_speed = 50
+extrusion_multiplier = 1
+min_fan_speed = 50
+bridge_fan_speed = 50

StaticData/PrinterSettings/Ultimaker/2 Extended/material/PLA.slice

@@ -0,0 +1,6 @@
+temperature = 210
+bed_temperature = 60
+max_fan_speed = 100
+extrusion_multiplier = 1
+min_fan_speed = 100
+bridge_fan_speed = 100

StaticData/PrinterSettings/Ultimaker/2 Extended/quality/Fast.slice

@@ -0,0 +1,6 @@
+layer_height = 0.15
+fill_density = 0.1
+first_layer_speed = 30
+infill_speed = 100
+external_perimeter_speed = 40
+perimeter_speed = 80

StaticData/PrinterSettings/Ultimaker/2 Extended/quality/High.slice

@@ -0,0 +1,6 @@
+layer_height = 0.06
+fill_density = 0.2
+first_layer_speed = 20
+infill_speed = 80
+external_perimeter_speed = 30
+perimeter_speed = 60

StaticData/PrinterSettings/Ultimaker/2 Extended/quality/Normal.slice

@@ -0,0 +1,6 @@
+layer_height = 0.1
+fill_density = 0.2
+first_layer_speed = 20
+infill_speed = 80
+external_perimeter_speed = 30
+perimeter_speed = 60

StaticData/PrinterSettings/Ultimaker/2 Extended/quality/Ulti.slice

@@ -0,0 +1,6 @@
+layer_height = 0.04
+fill_density = 0.2
+first_layer_speed = 20
+infill_speed = 80
+external_perimeter_speed = 30
+perimeter_speed = 60

StaticData/PrinterSettings/Ultimaker/2+/calibration.ini

@@ -0,0 +1 @@
+Calibration - Circle.stl

StaticData/PrinterSettings/Ultimaker/2+/config.ini

@@ -0,0 +1,160 @@
+avoid_crossing_perimeters = 1
+bed_shape = rectangular
+bed_size = 223,223
+bed_temperature = 70
+bottom_clip_amount = 0
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 20
+brim_width = 0
+build_height = 205
+cancel_gcode = G28
+center_part_on_bed = 1
+complete_objects = 0
+connect_gcode = 
+cool_extruder_lift = 0
+print_leveling_solution = 3 Point Plane
+print_leveling_method = Manual
+print_leveling_required_to_print = 0
+manual_probe_paper_width = .1
+cooling = 1
+create_raft = 0
+default_acceleration = 0
+disable_fan_first_layers = 1
+end_gcode = M104 S0                     ;extruder heater off\nM140 S0                     ;heated bed heater off (if you have it)\nG91                                    ;relative positioning\nG1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-5 X-20 Y-20 F1300 ;move Z up a bit and retract filament even more\nG28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way\nM84                         ;steppers off\nG90                         ;absolute positioning
+external_perimeter_speed = 70%
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_count = 1
+extruder_offset = 0x0,0x0,0x0,0x0
+extruder_wipe_temperature = 0
+extruders_share_temperature = 0
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 2.85
+fill_angle = 45
+fill_density = 0.2
+fill_pattern = honeycomb
+first_layer_acceleration = 0
+first_layer_bed_temperature = 75
+first_layer_height = 0.3
+first_layer_speed = 20
+first_layer_temperature = 205
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+gcode_output_type = REPRAP
+has_fan = 1
+has_hardware_leveling = 0
+has_heated_bed = 1
+has_power_control = 0
+has_sd_card_reader = 1
+show_reset_connection = 0
+heat_extruder_before_homing = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap_perimeter = .06
+infill_speed = 60
+infill_type = TRIANGLES
+layer_gcode = 
+layer_height = 0.2
+max_fan_speed = 100
+min_extrusion_before_retract = 0.02
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 10
+notes = 
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+pause_gcode = 
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 30
+perimeters = 3
+post_process = 
+print_center = 111,111
+raft_air_gap = 0.22
+raft_extruder = 0
+raft_extra_distance_around_part = 5
+raft_fan_speed_percent = 100
+raft_layers = 0
+raft_print_speed = 100%
+bed_remove_part_temperature = 0
+randomize_start = 0
+repair_outlines_extensive_stitching = 0
+repair_outlines_keep_open = 0
+resolution = 0
+resume_gcode =
+retract_before_travel = 1.5
+retract_layer_change = 1
+retract_length = 4.5
+retract_length_tool_change = 16.5
+retract_lift = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 40
+skirt_distance = 3
+skirt_height = 1
+skirts = 3
+slowdown_below_layer_time = 25
+small_perimeter_speed = 30
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+solid_shell = 0
+spiral_vase = 0
+standby_temperature_delta = -5
+start_gcode = G21        ;metric values\nG90        ;absolute positioning\nM82        ;set extruder to absolute mode\nM107       ;start with the fan off\nG28 X0 Y0  ;move X/Y to min endstops\nG28 Z0     ;move Z to min endstops\nM190 S70\nG1 Z15.0 F1800 ;move the platform down 15mm\nG1 Y10 F4000\nM109 S210\nG92 E0                  ;zero the extruded length\nG1 F200 E30              ;extrude 30mm of feed stock\nG92 E0                  ;zero the extruded length again\nG1 F130\nM117 Printing... 	;Put printing message on LCD screen
+start_perimeters_at_concave_points = 0
+start_perimeters_at_non_overhang = 0
+support_material = 0
+support_material_angle = 45
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_infill_angle = 45
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_pattern = honeycomb
+support_material_spacing = 2.5
+support_material_speed = 30
+support_material_threshold = 45
+support_material_xy_distance = 1
+support_material_z_distance = 0.15
+support_material_z_gap_layers = 1
+support_type = LINES
+temperature = 210
+thin_walls = 1
+threads = 2
+toolchange_gcode = 
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 0.8mm
+travel_speed = 150
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+wipe_shield_distance = 0
+wipe_tower_size = 0
+z_can_be_negative = 0
+z_offset = 0