Merge branch 'development' of https://github.com/MatterHackers/MatterControl into development

StaticData/PrinterSettings/ROBO 3D/R1PLUS/BedSettings.json

@@ -1 +0,0 @@
-{"ActualBedInImage":{"Left":48,"Bottom":48,"Right":974,"Top":974}}

StaticData/PrinterSettings/ROBO 3D/R1PLUS/config.ini

@@ -1,144 +0,0 @@
-avoid_crossing_perimeters = 1
-bed_shape = rectangular
-bed_size = 228,254
-bed_temperature = 90
-bottom_clip_amount = 0
-bottom_solid_layers = 1mm
-bridge_acceleration = 0
-bridge_fan_speed = 100
-bridge_flow_ratio = 1
-bridge_speed = 60
-brim_width = 0
-build_height = 200
-cancel_gcode = G28 X0\n
-center_part_on_bed = 1
-complete_objects = 0
-cool_extruder_lift = 0
-cooling = 0
-create_raft = 0
-raft_extra_distance_around_part = 5
-raft_air_gap = .2
-default_acceleration = 0
-disable_fan_first_layers = 0
-end_gcode = M104 S0 ; turn off temperature\nG1 X10 Y200\nM84     ; disable motors
-external_perimeter_speed = 50
-external_perimeters_first = 0
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extruder_offset = 0x0
-extrusion_axis = E
-extrusion_multiplier = 1
-extrusion_width = 0
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_diameter = 1.75
-fill_angle = 45
-fill_density = 0.25
-fill_pattern = rectilinear
-first_layer_acceleration = 0
-first_layer_bed_temperature = 90
-first_layer_extrusion_width = 1
-first_layer_height = 0.4
-first_layer_speed = 30%
-first_layer_temperature = 225
-g0 = 0
-gap_fill_speed = 20
-gcode_arcs = 0
-gcode_comments = 0
-gcode_flavor = reprap
-gcode_output_type = REPRAP
-has_sd_card_reader = 1
-has_hardware_leveling = 1
-infill_acceleration = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_first = 0
-infill_only_where_needed = 0
-infill_overlap_perimeter = .06
-infill_speed = 60
-infill_type = GRID
-layer_gcode = 
-layer_height = 0.1
-min_extrusion_before_retract = 0
-max_fan_speed = 100
-min_fan_speed = 100
-min_print_speed = 10
-min_skirt_length = 5
-notes = 
-nozzle_diameter = 0.4
-only_retract_when_crossing_perimeters = 0
-ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-pause_gcode = 
-perimeter_acceleration = 0
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_speed = 60
-perimeters = 2
-post_process = 
-print_center = 114,127
-raft_layers = 0
-randomize_start = 1
-repair_outlines_extensive_stitching = 0
-repair_outlines_keep_open = 0
-repair_overlaps_reverse_orientation = 0
-repair_overlaps_union_all_together = 0
-resolution = 0
-resume_gcode = 
-retract_before_travel = 20
-retract_layer_change = 1
-retract_length = 1
-retract_length_tool_change = 10
-retract_lift = .5
-retract_restart_extra = 0
-retract_restart_extra_toolchange = 0
-retract_speed = 30
-skirt_distance = 6
-skirt_height = 1
-skirts = 2
-slowdown_below_layer_time = 10
-small_perimeter_speed = 35
-solid_fill_pattern = rectilinear
-solid_infill_below_area = 70
-solid_infill_every_layers = 0
-solid_infill_extrusion_width = 0
-solid_infill_speed = 60
-spiral_vase = 0
-standby_temperature_delta = -5
-start_gcode = G28 X0 Y0 Z0 ; home all axes\nG1 Z5 F5000 ; lift nozzle\nM109 S[temperature] ; set the extruder temp and wait\nG28 X0 Y0 Z0 ; Home Z again in case there was filament on nozzle\nG29 ; probe the bed
-start_perimeters_at_concave_points = 0
-start_perimeters_at_non_overhang = 0
-support_material = 1
-support_material_angle = 0
-support_material_create_internal_support = 0
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 3
-support_material_interface_spacing = 0
-support_material_pattern = rectilinear
-support_material_spacing = 3
-support_material_speed = 60
-support_material_threshold = 40
-support_material_xy_distance = 0.7
-support_material_z_distance = 0.15
-support_material_z_gap_layers = 1
-support_type = LINES
-temperature = 215
-thin_walls = 1
-threads = 2
-toolchange_gcode = 
-top_infill_extrusion_width = 0
-top_solid_infill_speed = 50
-top_solid_layers = 1mm
-travel_speed = 150
-use_firmware_retraction = 0
-use_relative_e_distances = 0
-vibration_limit = 0
-wipe = 0
-wipe_shield_distance = 0
-z_offset = 0

StaticData/PrinterSettings/ROBO 3D/R1PLUS/material/ABS.slice

@@ -1,8 +0,0 @@
-bed_temperature = 80
-disable_fan_first_layers = 0
-fan_always_on = 0
-first_layer_bed_temperature = 80
-first_layer_temperature = 235
-retract_length = 1
-temperature = 235
-retract_speed = 30

StaticData/PrinterSettings/ROBO 3D/R1PLUS/material/PLA.slice

@@ -1,7 +0,0 @@
-bed_temperature = 50
-disable_fan_first_layers = 2
-fan_always_on = 1
-first_layer_bed_temperature = 55
-first_layer_temperature = 210
-retract_length = 3
-temperature = 210

StaticData/PrinterSettings/ROBO 3D/R1PLUS/quality/High.slice

@@ -1,5 +0,0 @@
-layer_height = 0.1
-first_layer_height = 0.3
-perimeters = 2
-fill_density = 0.25
-top_solid_layers = 8

StaticData/PrinterSettings/ROBO 3D/R1PLUS/quality/Low.slice

@@ -1,9 +0,0 @@
-layer_height = 0.3
-first_layer_height = 0.3
-bottom_clip_amount = 0
-perimeters = 2
-top_solid_layers = 3
-fill_density = 0.2
-fill_pattern = rectilinear
-solid_infill_below_area = 40
-infill_speed = 60

StaticData/PrinterSettings/ROBO 3D/R1PLUS/quality/Medium.slice

@@ -1,4 +0,0 @@
-layer_height = 0.2
-first_layer_height = 0.3
-perimeters = 2
-fill_density = 0.25

StaticData/PrinterSettings/ROBO 3D/R1PLUS/setup.ini

@@ -1,6 +0,0 @@
-baud_rate = 250000
-windows_driver = MHSerial.inf
-default_material_presets = PLA
-default_quality_preset = Medium
-default_macros = Offset 0.8, Offset 0.9,Offset 1,Offset 1.1,Offset 1.2
-