diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/calibration.ini b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/calibration.ini
new file mode 100644
index 000000000..4a238c26d
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/calibration.ini	
@@ -0,0 +1 @@
+Calibration - Box.stl
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/config.ini b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/config.ini
new file mode 100644
index 000000000..3ba5d5b6f
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/config.ini	
@@ -0,0 +1,152 @@
+avoid_crossing_perimeters = 1
+bed_shape = rectangular
+bed_size = 310,310
+bed_temperature = 0
+bottom_clip_amount = 0
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 0.8
+bridge_speed = 27
+brim_width = 0.5
+build_height = 260
+cancel_gcode = G91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nG1 E-10 F500 ; Retract Extruder\nG90;\nG28 X0;   Home X axis\nG1 Y225 F3000; bring plate to front\nM84;
+center_part_on_bed = 1
+complete_objects = 1
+cool_extruder_lift = 0
+cooling = 1
+create_raft = 1
+default_acceleration = 0
+disable_fan_first_layers = 1
+end_gcode = M104 S0 ; turn off temperature\nG91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nG1 E-10 F500 ; Retract Extruder\nG90;\nG28 X0  ; home X axis\nG1 Y225 F3000; bring plate to front\nM84;
+external_perimeter_speed = 40
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 35
+extruder_clearance_radius = 40
+extruder_count = 1
+extruder_offset = 0x0
+extruders_share_temperature = 0
+extrusion_axis = E
+extrusion_multiplier = 1.0
+extrusion_width = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.74
+fill_angle = 45
+fill_density = 0.2
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_bed_temperature = 0
+first_layer_extrusion_width = 100%
+first_layer_height = 0.25
+first_layer_speed = 25
+first_layer_temperature = 205
+g0 = 0
+gap_fill_speed = 15
+gcode_arcs = 0
+gcode_comments = 1
+gcode_flavor = reprap
+gcode_output_type = REPRAP
+has_fan = 1
+has_hardware_leveling = 0
+has_heated_bed = 0
+has_sd_card_reader = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 1
+infill_overlap_perimeter = .06
+infill_speed = 40
+infill_type = LINES
+layer_gcode = 
+layer_height = 0.25
+max_fan_speed = 100
+min_extrusion_before_retract = 0.1
+min_fan_speed = 50
+min_print_speed = 10
+min_skirt_length = 2
+notes = 
+nozzle_diameter = 0.7
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+pause_gcode = G1 X0 Y0 F3000; home all axes\nM84 S0
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 40
+perimeters = 2
+post_process = 
+print_center = 150,150
+raft_air_gap = 0.3
+raft_extruder = 0
+raft_extra_distance_around_part = 3
+raft_fan_speed_percent = 50
+raft_layers = 0
+raft_print_speed = 25
+randomize_start = 1
+repair_outlines_extensive_stitching = 1
+repair_outlines_keep_open = 0
+resolution = 0
+resume_gcode = 
+retract_before_travel = 3
+retract_layer_change = 0
+retract_length = 1
+retract_length_tool_change = 10
+retract_lift = 0.0125
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 25
+skirt_distance = 0.7
+skirt_height = 2
+skirts = 3
+slowdown_below_layer_time = 10
+small_perimeter_speed = 10
+solid_fill_pattern = concentric
+solid_infill_below_area = 70
+solid_infill_every_layers = 20
+solid_infill_extrusion_width = 0
+solid_infill_speed = 90%
+spiral_vase = 0
+standby_temperature_delta = -5
+start_gcode = G28 X0 Y0 ; home all axes\nM109 S[temperature]\nG28 Y0 Z0\nG91
+start_perimeters_at_concave_points = 1
+start_perimeters_at_non_overhang = 1
+support_material = 0
+support_material_angle = 45
+support_material_create_internal_support = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_infill_angle = 45
+support_material_interface_extruder = 1
+support_material_interface_layers = 2
+support_material_interface_spacing = 0
+support_material_pattern = honeycomb
+support_material_spacing = 2.5
+support_material_speed = 25
+support_material_threshold = 25
+support_material_xy_distance = 0.8
+support_material_z_distance = 0.15
+support_material_z_gap_layers = 4
+support_type = LINES
+temperature = 205
+thin_walls = 1
+threads = 2
+toolchange_gcode = 
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 35
+top_solid_layers = 4
+travel_speed = 90
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 1
+wipe_shield_distance = 0
+wipe_tower_size = 0
+z_can_be_negative = 0
+z_offset = 0
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Black.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Black.slice
new file mode 100644
index 000000000..1fa5bb532
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Black.slice	
@@ -0,0 +1,2 @@
+temperature = 205
+first_layer_temperature = 205
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Blue.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Blue.slice
new file mode 100644
index 000000000..01d901ccd
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Blue.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 205
+temperature = 205
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Clear.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Clear.slice
new file mode 100644
index 000000000..01d901ccd
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Clear.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 205
+temperature = 205
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Green.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Green.slice
new file mode 100644
index 000000000..f74ea1fcd
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Green.slice	
@@ -0,0 +1,3 @@
+filament_diameter = 1.74
+first_layer_temperature = 200
+temperature = 200
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Ivory.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Ivory.slice
new file mode 100644
index 000000000..fe8fd0661
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Ivory.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Orange.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Orange.slice
new file mode 100644
index 000000000..fe8fd0661
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Orange.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Pink.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Pink.slice
new file mode 100644
index 000000000..fe8fd0661
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Pink.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Purple.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Purple.slice
new file mode 100644
index 000000000..fe8fd0661
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Purple.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Red.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Red.slice
new file mode 100644
index 000000000..fe8fd0661
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Red.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Silver.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Silver.slice
new file mode 100644
index 000000000..fe8fd0661
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Silver.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-White.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-White.slice
new file mode 100644
index 000000000..9cd6b02da
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-White.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 210
+temperature = 210
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Yellow.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Yellow.slice
new file mode 100644
index 000000000..fe8fd0661
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Basic-Yellow.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Crystal-Trans. Blue.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Crystal-Trans. Blue.slice
new file mode 100644
index 000000000..49bfe0857
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Crystal-Trans. Blue.slice	
@@ -0,0 +1,3 @@
+filament_diameter = 1.72
+first_layer_temperature = 220
+temperature = 220
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Crystal-Trans. Orange.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Crystal-Trans. Orange.slice
new file mode 100644
index 000000000..e149d85f6
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Crystal-Trans. Orange.slice	
@@ -0,0 +1,3 @@
+filament_diameter = 1.8
+first_layer_temperature = 220
+temperature = 220
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Crystal-Trans. Red.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Crystal-Trans. Red.slice
new file mode 100644
index 000000000..6d535d7f0
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Crystal-Trans. Red.slice	
@@ -0,0 +1,3 @@
+filament_diameter = 1.78
+first_layer_temperature = 220
+temperature = 220
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Crystal-Trans. Yellow.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Crystal-Trans. Yellow.slice
new file mode 100644
index 000000000..24a4c1ef2
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Crystal-Trans. Yellow.slice	
@@ -0,0 +1,3 @@
+filament_diameter = 1.75
+first_layer_temperature = 220
+temperature = 220
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Max-Black.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Max-Black.slice
new file mode 100644
index 000000000..f3e75ea15
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Max-Black.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.79
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Max-White.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Max-White.slice
new file mode 100644
index 000000000..f3e75ea15
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/PLA Max-White.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.79
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/Timber-Wood.slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/Timber-Wood.slice
new file mode 100644
index 000000000..b67d15569
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/material/Timber-Wood.slice	
@@ -0,0 +1,8 @@
+first_layer_temperature = 200
+temperature = 200
+retract_length = 2
+retract_speed = 55
+infill_speed = 50
+perimeter_speed = 50
+external_perimeter_speed = 45
+support_material_speed = 50
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/High [Default].slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/High [Default].slice
new file mode 100644
index 000000000..e763c3af7
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/High [Default].slice	
@@ -0,0 +1 @@
+layer_height = 0.15
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/High [no infill-hollow].slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/High [no infill-hollow].slice
new file mode 100644
index 000000000..53f736a83
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/High [no infill-hollow].slice	
@@ -0,0 +1,2 @@
+layer_height = 0.15
+fill_density = 0
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/High [with support structure].slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/High [with support structure].slice
new file mode 100644
index 000000000..ec55131d9
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/High [with support structure].slice	
@@ -0,0 +1,2 @@
+layer_height = 0.15
+support_material = 1
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Standard [Default].slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Standard [Default].slice
new file mode 100644
index 000000000..95d1be5e8
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Standard [Default].slice	
@@ -0,0 +1 @@
+layer_height = 0.25
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Standard [no infill-hollow].slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Standard [no infill-hollow].slice
new file mode 100644
index 000000000..308a1c6de
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Standard [no infill-hollow].slice	
@@ -0,0 +1,2 @@
+layer_height = 0.25
+fill_density = 0
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Standard [with support structure].slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Standard [with support structure].slice
new file mode 100644
index 000000000..0164f05ac
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Standard [with support structure].slice	
@@ -0,0 +1,2 @@
+layer_height = 0.25
+support_material = 1
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Super High [Default].slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Super High [Default].slice
new file mode 100644
index 000000000..76fe48063
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Super High [Default].slice	
@@ -0,0 +1 @@
+layer_height = 0.09
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Super High [no infill-hollow].slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Super High [no infill-hollow].slice
new file mode 100644
index 000000000..dcb68c3d5
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Super High [no infill-hollow].slice	
@@ -0,0 +1,2 @@
+layer_height = 0.09
+fill_density = 0
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Super High [with support structure].slice b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Super High [with support structure].slice
new file mode 100644
index 000000000..cea752e5d
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/quality/Super High [with support structure].slice	
@@ -0,0 +1,2 @@
+layer_height = 0.09
+support_material = 1
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/setup.ini b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/setup.ini
new file mode 100644
index 000000000..19cb07970
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/Mega i3/setup.ini	
@@ -0,0 +1,4 @@
+baud_rate = 250000
+default_slice_engine = MatterSlice
+default_material_presets = PLA Basic-Clear
+windows_driver = MHSerial.inf
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/calibration.ini b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/calibration.ini
new file mode 100644
index 000000000..4a238c26d
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/calibration.ini	
@@ -0,0 +1 @@
+Calibration - Box.stl
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/config.ini b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/config.ini
new file mode 100644
index 000000000..07649b29a
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/config.ini	
@@ -0,0 +1,152 @@
+avoid_crossing_perimeters = 1
+bed_shape = rectangular
+bed_size = 210,210
+bed_temperature = 0
+bottom_clip_amount = 0
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 20
+brim_width = 0
+build_height = 200
+cancel_gcode = 
+center_part_on_bed = 1
+complete_objects = 0
+cool_extruder_lift = 0
+cooling = 1
+create_raft = 1
+default_acceleration = 0
+disable_fan_first_layers = 1
+end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors
+external_perimeter_speed = 45
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_count = 1
+extruder_offset = 0x0,0x0,0x0,0x0
+extruders_share_temperature = 0
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 45
+fill_density = 0.2
+fill_pattern = honeycomb
+first_layer_acceleration = 0
+first_layer_bed_temperature = 75
+first_layer_extrusion_width = 100%
+first_layer_height = 0.3
+first_layer_speed = 30%
+first_layer_temperature = 205
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+gcode_output_type = REPRAP
+has_fan = 1
+has_hardware_leveling = 0
+has_heated_bed = 0
+has_sd_card_reader = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap_perimeter = .06
+infill_speed = 45
+infill_type = TRIANGLES
+layer_gcode = 
+layer_height = 0.25
+max_fan_speed = 100
+min_extrusion_before_retract = .1
+min_fan_speed = 50
+min_print_speed = 10
+min_skirt_length = 0
+notes = 
+nozzle_diameter = 0.7
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+pause_gcode = 
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 45
+perimeters = 3
+post_process = 
+print_center = 100,100
+raft_air_gap = 0.35
+raft_extruder = 0
+raft_extra_distance_around_part = 5
+raft_fan_speed_percent = 50
+raft_layers = 0
+raft_print_speed = 100%
+randomize_start = 0
+repair_outlines_extensive_stitching = 0
+repair_outlines_keep_open = 0
+resolution = 0
+resume_gcode = 
+retract_before_travel = 20
+retract_layer_change = 1
+retract_length = 1
+retract_length_tool_change = 10
+retract_lift = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+skirt_distance = 6
+skirt_height = 1
+skirts = 1
+slowdown_below_layer_time = 30
+small_perimeter_speed = 30
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+standby_temperature_delta = -5
+start_gcode = G28 X0 Y0 ; home all axes\nM109 S[temperature]\nG28 Y0 Z0\nG91\n\n
+start_perimeters_at_concave_points = 0
+start_perimeters_at_non_overhang = 0
+support_material = 0
+support_material_angle = 45
+support_material_create_internal_support = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_infill_angle = 45
+support_material_interface_extruder = 1
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_pattern = honeycomb
+support_material_spacing = 2.5
+support_material_speed = 40
+support_material_threshold = 0
+support_material_xy_distance = 0.7
+support_material_z_distance = 0.15
+support_material_z_gap_layers = 1
+support_type = LINES
+temperature = 200
+thin_walls = 1
+threads = 2
+toolchange_gcode = 
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 3
+travel_speed = 90
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+wipe_shield_distance = 0
+wipe_tower_size = 0
+z_can_be_negative = 0
+z_offset = 0
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Black.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Black.slice
new file mode 100644
index 000000000..1fa5bb532
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Black.slice	
@@ -0,0 +1,2 @@
+temperature = 205
+first_layer_temperature = 205
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Blue.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Blue.slice
new file mode 100644
index 000000000..01d901ccd
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Blue.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 205
+temperature = 205
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Clear.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Clear.slice
new file mode 100644
index 000000000..01d901ccd
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Clear.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 205
+temperature = 205
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Green.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Green.slice
new file mode 100644
index 000000000..f74ea1fcd
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Green.slice	
@@ -0,0 +1,3 @@
+filament_diameter = 1.74
+first_layer_temperature = 200
+temperature = 200
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Ivory.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Ivory.slice
new file mode 100644
index 000000000..fe8fd0661
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Ivory.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Orange.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Orange.slice
new file mode 100644
index 000000000..fe8fd0661
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Orange.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Pink.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Pink.slice
new file mode 100644
index 000000000..fe8fd0661
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Pink.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Purple.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Purple.slice
new file mode 100644
index 000000000..fe8fd0661
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Purple.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Red.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Red.slice
new file mode 100644
index 000000000..fe8fd0661
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Red.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Silver.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Silver.slice
new file mode 100644
index 000000000..fe8fd0661
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Silver.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-White.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-White.slice
new file mode 100644
index 000000000..9cd6b02da
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-White.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 210
+temperature = 210
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Yellow.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Yellow.slice
new file mode 100644
index 000000000..fe8fd0661
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Basic-Yellow.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.74
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Crystal-Trans. Blue.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Crystal-Trans. Blue.slice
new file mode 100644
index 000000000..49bfe0857
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Crystal-Trans. Blue.slice	
@@ -0,0 +1,3 @@
+filament_diameter = 1.72
+first_layer_temperature = 220
+temperature = 220
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Crystal-Trans. Orange.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Crystal-Trans. Orange.slice
new file mode 100644
index 000000000..e149d85f6
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Crystal-Trans. Orange.slice	
@@ -0,0 +1,3 @@
+filament_diameter = 1.8
+first_layer_temperature = 220
+temperature = 220
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Crystal-Trans. Red.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Crystal-Trans. Red.slice
new file mode 100644
index 000000000..6d535d7f0
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Crystal-Trans. Red.slice	
@@ -0,0 +1,3 @@
+filament_diameter = 1.78
+first_layer_temperature = 220
+temperature = 220
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Crystal-Trans. Yellow.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Crystal-Trans. Yellow.slice
new file mode 100644
index 000000000..24a4c1ef2
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Crystal-Trans. Yellow.slice	
@@ -0,0 +1,3 @@
+filament_diameter = 1.75
+first_layer_temperature = 220
+temperature = 220
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Max-Black.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Max-Black.slice
new file mode 100644
index 000000000..f3e75ea15
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Max-Black.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.79
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Max-White.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Max-White.slice
new file mode 100644
index 000000000..f3e75ea15
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/PLA Max-White.slice	
@@ -0,0 +1,3 @@
+first_layer_temperature = 200
+temperature = 200
+filament_diameter = 1.79
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/Timber-Wood.slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/Timber-Wood.slice
new file mode 100644
index 000000000..b67d15569
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/material/Timber-Wood.slice	
@@ -0,0 +1,8 @@
+first_layer_temperature = 200
+temperature = 200
+retract_length = 2
+retract_speed = 55
+infill_speed = 50
+perimeter_speed = 50
+external_perimeter_speed = 45
+support_material_speed = 50
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/High [Default].slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/High [Default].slice
new file mode 100644
index 000000000..e763c3af7
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/High [Default].slice	
@@ -0,0 +1 @@
+layer_height = 0.15
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/High [no infill-hollow].slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/High [no infill-hollow].slice
new file mode 100644
index 000000000..53f736a83
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/High [no infill-hollow].slice	
@@ -0,0 +1,2 @@
+layer_height = 0.15
+fill_density = 0
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/High [with support structure].slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/High [with support structure].slice
new file mode 100644
index 000000000..ec55131d9
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/High [with support structure].slice	
@@ -0,0 +1,2 @@
+layer_height = 0.15
+support_material = 1
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Standard [Default].slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Standard [Default].slice
new file mode 100644
index 000000000..95d1be5e8
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Standard [Default].slice	
@@ -0,0 +1 @@
+layer_height = 0.25
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Standard [no infill-hollow].slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Standard [no infill-hollow].slice
new file mode 100644
index 000000000..308a1c6de
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Standard [no infill-hollow].slice	
@@ -0,0 +1,2 @@
+layer_height = 0.25
+fill_density = 0
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Standard [with support structure].slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Standard [with support structure].slice
new file mode 100644
index 000000000..0164f05ac
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Standard [with support structure].slice	
@@ -0,0 +1,2 @@
+layer_height = 0.25
+support_material = 1
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Super High [Default].slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Super High [Default].slice
new file mode 100644
index 000000000..76fe48063
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Super High [Default].slice	
@@ -0,0 +1 @@
+layer_height = 0.09
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Super High [no infill-hollow].slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Super High [no infill-hollow].slice
new file mode 100644
index 000000000..dcb68c3d5
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Super High [no infill-hollow].slice	
@@ -0,0 +1,2 @@
+layer_height = 0.09
+fill_density = 0
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Super High [with support structure].slice b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Super High [with support structure].slice
new file mode 100644
index 000000000..cea752e5d
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/quality/Super High [with support structure].slice	
@@ -0,0 +1,2 @@
+layer_height = 0.09
+support_material = 1
\ No newline at end of file
diff --git a/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/setup.ini b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/setup.ini
new file mode 100644
index 000000000..19cb07970
--- /dev/null
+++ b/StaticData/PrinterSettings/3D Stuffmaker/i3 Plus+/setup.ini	
@@ -0,0 +1,4 @@
+baud_rate = 250000
+default_slice_engine = MatterSlice
+default_material_presets = PLA Basic-Clear
+windows_driver = MHSerial.inf