Updated Print Space Altair profile

StaticData/PrinterSettings/PrintSpace/Altair/config.ini

@@ -22,8 +22,8 @@ manual_probe_paper_width = .1
 cooling = 1
 create_raft = 0
 default_acceleration = 0
-disable_fan_first_layers = 2
-end_gcode = G1 E-2 F12000 ; retract filament\nM104 S0 ; turn off temperature\nM140 S0\nG28\nM84     ; disable motors
+disable_fan_first_layers = 3
+end_gcode = G91 ; set relative coordinate system \nG1 E-2 F12000 ; retract filament\nG90 ; set absolute coordinate system\nM104 S0 ; turn off hotend temperature\nM140 S0 ; turn off bed temperature\nG28 ; home all axes\nM84 ; disable motors
 external_perimeter_speed = 60
 external_perimeters_first = 0
 extra_perimeters = 1
@@ -61,6 +61,7 @@ has_power_control = 0
 has_sd_card_reader = 1
 show_reset_connection = 1
 heat_extruder_before_homing = 0
+include_firmware_updater = None
 infill_acceleration = 0
 infill_every_layers = 1
 infill_extruder = 1
@@ -70,6 +71,7 @@ infill_only_where_needed = 0
 infill_overlap_perimeter = .06
 infill_speed = 40
 infill_type = TRIANGLES
+layer_gcode = 
 layer_height = 0.2
 layer_to_pause = 
 max_fan_speed = 100
@@ -83,7 +85,7 @@ only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base].gcode
 overhangs = 1
-pause_gcode = G91\nG1 Z10 E-10 F12000\nG90
+pause_gcode = 
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0.6
@@ -103,7 +105,7 @@ randomize_start =
 repair_outlines_extensive_stitching = 1
 repair_outlines_keep_open = 1
 resolution = 0
-resume_gcode = G91\nG1 Z-10 E10.5 F12000\nG90
+resume_gcode = 
 retract_before_travel = 30
 retract_layer_change = 0
 retract_length = 3
@@ -126,7 +128,7 @@ solid_infill_speed = 30
 solid_shell = 0
 spiral_vase = 0
 standby_temperature_delta = -5
-start_gcode = G28 ; home all axes\nG0 Z10\nG30 Z-0.2 F1000 ; set bed height\nG0 Z5 ; lift nozzle before print\n; G91\n; G1 E-1 F12000\n; G90
+start_gcode = G28 ; home all axes\nG0 Z10\nG30 Z-0.2 F1000 ; set bed height\nG0 Z5 ; lift nozzle before print
 start_perimeters_at_concave_points = 0
 start_perimeters_at_non_overhang = 0
 support_air_gap = .3
@@ -157,7 +159,7 @@ toolchange_gcode =
 top_infill_extrusion_width = 0.6
 top_solid_infill_speed = 40
 top_solid_layers = 1mm
-travel_speed = 200
+travel_speed = 100
 use_firmware_retraction = 0
 use_relative_e_distances = 0
 vibration_limit = 0
@@ -165,4 +167,4 @@ wipe = 0
 wipe_shield_distance = 0
 wipe_tower_size = 0
 z_can_be_negative = 1
-z_offset = 0
+z_offset = 0

StaticData/PrinterSettings/PrintSpace/Altair/material/ABS.slice

@@ -3,6 +3,6 @@ temperature = 235
 bed_temperature = 100
 min_fan_speed = 0
 disable_fan_first_layers = 0
-bridge_fan_speed = 50
+bridge_fan_speed = 0
 perimeter_speed = 40
 external_perimeter_speed = 45