Added settings for Printrbot Metal Plus (dual extrusion, heated bed, no heated bed)

StaticData/PrinterSettings/Printrbot/Metal Plus (Dual Extrusion)/config.ini

@@ -0,0 +1,129 @@
+avoid_crossing_perimeters = 1
+bed_shape = rectangular
+bed_size = 196,254
+bed_temperature = 60
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 0
+bridge_flow_ratio = 1
+bridge_speed = 20
+brim_width = 0
+build_height = 254
+complete_objects = 0
+cool_extruder_lift = 0
+cooling = 1
+default_acceleration = 0
+disable_fan_first_layers = 2
+end_gcode = M104 S0 ; turn off temperature\nM140 S0\nG28 X0 Y0 ; home X/Y axis\nM84     ; disable motors
+external_perimeter_speed = 30
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_count = 2
+extruder_offset = 0x0
+extruders_share_temperature = 0
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 45
+fill_density = 0.35
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_bed_temperature = 60
+first_layer_extrusion_width = 200%
+first_layer_height = .42
+first_layer_speed = 15
+first_layer_temperature = 235
+g0 = 0
+gap_fill_speed = 30
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+has_fan = 1
+has_heated_bed = 1
+has_sd_card_reader = 1
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 30
+layer_gcode = 
+layer_height = 0.21
+min_extrusion_before_retract = .1
+max_fan_speed = 0
+min_fan_speed = 0
+min_print_speed = 2
+min_skirt_length = 0
+notes = 
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 30
+perimeters = 1
+post_process = 
+print_center = 98,127
+raft_layers = 0
+randomize_start = 1
+resolution = 0
+retract_before_travel = 20
+retract_layer_change = 1
+retract_length = 7
+retract_length_tool_change = 10
+retract_lift = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 50
+skirt_distance = 2
+skirt_height = 1
+skirts = 3
+slowdown_below_layer_time = 15
+small_perimeter_speed = 30
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 1
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 30
+spiral_vase = 0
+standby_temperature_delta = -5
+start_gcode = G28 ; home all axes\nM117 
+start_perimeters_at_concave_points = 0
+start_perimeters_at_non_overhang = 0
+support_material = 0
+support_material_angle = 0
+support_material_create_internal_support = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 2.5
+support_material_speed = 30
+support_material_threshold = 75
+support_material_xy_distance = 0.7
+support_material_z_distance = 0.15
+temperature = 225
+thin_walls = 1
+threads = 2
+toolchange_gcode = 
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 30
+top_solid_layers = 4
+travel_speed = 100
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0

StaticData/PrinterSettings/Printrbot/Metal Plus (Dual Extrusion)/material/ABS.slice

@@ -0,0 +1,4 @@
+bed_temperature = 80
+first_layer_bed_temperature = 80
+first_layer_temperature = 235
+temperature = 225

StaticData/PrinterSettings/Printrbot/Metal Plus (Dual Extrusion)/material/PLA.slice

@@ -0,0 +1,4 @@
+bed_temperature = 0
+first_layer_bed_temperature = 0
+first_layer_temperature = 215
+temperature = 210

StaticData/PrinterSettings/Printrbot/Metal Plus (Dual Extrusion)/quality/Coarse.slice

@@ -0,0 +1 @@
+layer_height = 0.3

StaticData/PrinterSettings/Printrbot/Metal Plus (Dual Extrusion)/quality/Fine.slice

@@ -0,0 +1 @@
+layer_height = 0.1

StaticData/PrinterSettings/Printrbot/Metal Plus (Dual Extrusion)/quality/Standard.slice

@@ -0,0 +1 @@
+layer_height = 0.2

StaticData/PrinterSettings/Printrbot/Metal Plus (Dual Extrusion)/setup.ini

@@ -0,0 +1,5 @@
+baud_rate = 250000
+windows_driver = MHSerial.inf
+default_material_presets = PLA
+default_quality_preset = Standard
+

StaticData/PrinterSettings/Printrbot/Metal Plus (Heated Bed)/config.ini

@@ -0,0 +1,151 @@
+avoid_crossing_perimeters = 1
+bed_shape = rectangular
+bed_size = 254,254
+bed_temperature = 60
+bottom_clip_amount = 0
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+build_height = 254
+cancel_gcode = G28 X0\n
+center_part_on_bed = 1
+complete_objects = 0
+cool_extruder_lift = 0
+cooling = 0
+create_raft = 0
+default_acceleration = 0
+disable_fan_first_layers = 0
+end_gcode = M104 S0 ; turn off temperature\nG1 X10 Y200\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_count = 1
+extruder_offset = 0x0
+extruders_share_temperature = 0
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 45
+fill_density = 0.25
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_bed_temperature = 60
+first_layer_extrusion_width = 1
+first_layer_height = 0.3
+first_layer_speed = 30%
+first_layer_temperature = 230
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+gcode_output_type = REPRAP
+has_fan = 1
+has_heated_bed = 1
+has_sd_card_reader = 1
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap_perimeter = .06
+infill_speed = 60
+infill_type = GRID
+layer_gcode = 
+layer_height = 0.2
+max_fan_speed = 100
+min_extrusion_before_retract = 0
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 5
+notes = 
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+pause_gcode = 
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 2
+post_process = 
+print_center = 127,127
+raft_air_gap = .2
+raft_extruder = 0
+raft_extra_distance_around_part = 5
+raft_fan_speed_percent = 100
+raft_layers = 0
+raft_print_speed = 100%
+randomize_start = 1
+repair_outlines_extensive_stitching = 0
+repair_outlines_keep_open = 0
+resolution = 0
+resume_gcode = 
+retract_before_travel = 20
+retract_layer_change = 1
+retract_length = 1
+retract_length_tool_change = 10
+retract_lift = .5
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 10
+small_perimeter_speed = 35
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+standby_temperature_delta = -5
+start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\nM109 S[temperature] ; set the extruder temp and wait\nG28 Z0 ; Home Z again in case there was filament on nozzle\nM565 Z0\nG29 ; probe the bed
+start_perimeters_at_concave_points = 0
+start_perimeters_at_non_overhang = 0
+support_material = 1
+support_material_angle = 0
+support_material_create_internal_support = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_infill_angle = 45
+support_material_interface_extruder = 1
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 3
+support_material_speed = 60
+support_material_threshold = 40
+support_material_xy_distance = 0.7
+support_material_z_distance = 0.15
+support_material_z_gap_layers = 1
+support_type = LINES
+temperature = 225
+thin_walls = 1
+threads = 2
+toolchange_gcode = 
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 3
+travel_speed = 150
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+wipe_shield_distance = 0
+wipe_tower_size = 0
+z_can_be_negative = 0
+z_offset = 1

StaticData/PrinterSettings/Printrbot/Metal Plus (Heated Bed)/material/ABS.slice

@@ -0,0 +1,4 @@
+bed_temperature = 80
+first_layer_bed_temperature = 80
+first_layer_temperature = 235
+temperature = 225

StaticData/PrinterSettings/Printrbot/Metal Plus (Heated Bed)/material/PLA.slice

@@ -0,0 +1,4 @@
+bed_temperature = 0
+first_layer_bed_temperature = 0
+temperature = 205
+first_layer_temperature = 215

StaticData/PrinterSettings/Printrbot/Metal Plus (Heated Bed)/quality/Coarse.slice

@@ -0,0 +1 @@
+layer_height = 0.3

StaticData/PrinterSettings/Printrbot/Metal Plus (Heated Bed)/quality/Fine.slice

@@ -0,0 +1 @@
+layer_height = 0.1

StaticData/PrinterSettings/Printrbot/Metal Plus (Heated Bed)/quality/Standard.slice

@@ -0,0 +1 @@
+layer_height = 0.2

StaticData/PrinterSettings/Printrbot/Metal Plus (Heated Bed)/setup.ini

@@ -0,0 +1,5 @@
+baud_rate = 250000
+windows_driver = MHSerial.inf
+default_material_presets = PLA
+default_quality_preset = Standard
+

StaticData/PrinterSettings/Printrbot/Metal Plus (No Heated Bed)/config.ini

@@ -0,0 +1,151 @@
+avoid_crossing_perimeters = 1
+bed_shape = rectangular
+bed_size = 254,254
+bed_temperature = 0
+bottom_clip_amount = 0
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+build_height = 254
+cancel_gcode = G28 X0\n
+center_part_on_bed = 1
+complete_objects = 0
+cool_extruder_lift = 0
+cooling = 0
+create_raft = 0
+default_acceleration = 0
+disable_fan_first_layers = 0
+end_gcode = M104 S0 ; turn off temperature\nG1 X10 Y200\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_count = 1
+extruder_offset = 0x0
+extruders_share_temperature = 0
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 45
+fill_density = 0.25
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_bed_temperature = 0
+first_layer_extrusion_width = 1
+first_layer_height = 0.3
+first_layer_speed = 30%
+first_layer_temperature = 215
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+gcode_output_type = REPRAP
+has_fan = 1
+has_heated_bed = 0
+has_sd_card_reader = 1
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap_perimeter = .06
+infill_speed = 60
+infill_type = GRID
+layer_gcode = 
+layer_height = 0.2
+max_fan_speed = 100
+min_extrusion_before_retract = 0
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 5
+notes = 
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+pause_gcode = 
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 2
+post_process = 
+print_center = 127,127
+raft_air_gap = .2
+raft_extruder = 0
+raft_extra_distance_around_part = 5
+raft_fan_speed_percent = 100
+raft_layers = 0
+raft_print_speed = 100%
+randomize_start = 1
+repair_outlines_extensive_stitching = 0
+repair_outlines_keep_open = 0
+resolution = 0
+resume_gcode = 
+retract_before_travel = 20
+retract_layer_change = 1
+retract_length = 1
+retract_length_tool_change = 10
+retract_lift = .5
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 10
+small_perimeter_speed = 35
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+standby_temperature_delta = -5
+start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\nM109 S[temperature] ; set the extruder temp and wait\nG28 Z0 ; Home Z again in case there was filament on nozzle\nM565 Z0\nG29 ; probe the bed
+start_perimeters_at_concave_points = 0
+start_perimeters_at_non_overhang = 0
+support_material = 1
+support_material_angle = 0
+support_material_create_internal_support = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_infill_angle = 45
+support_material_interface_extruder = 1
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 3
+support_material_speed = 60
+support_material_threshold = 40
+support_material_xy_distance = 0.7
+support_material_z_distance = 0.15
+support_material_z_gap_layers = 1
+support_type = LINES
+temperature = 205
+thin_walls = 1
+threads = 2
+toolchange_gcode = 
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 3
+travel_speed = 150
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+wipe_shield_distance = 0
+wipe_tower_size = 0
+z_can_be_negative = 0
+z_offset = 1

StaticData/PrinterSettings/Printrbot/Metal Plus (No Heated Bed)/quality/Coarse.slice

@@ -0,0 +1 @@
+layer_height = 0.3

StaticData/PrinterSettings/Printrbot/Metal Plus (No Heated Bed)/quality/Fine.slice

@@ -0,0 +1 @@
+layer_height = 0.1

StaticData/PrinterSettings/Printrbot/Metal Plus (No Heated Bed)/quality/Standard.slice

@@ -0,0 +1 @@
+layer_height = 0.2

StaticData/PrinterSettings/Printrbot/Metal Plus (No Heated Bed)/setup.ini

@@ -0,0 +1,4 @@
+baud_rate = 250000
+windows_driver = MHSerial.inf
+default_quality_preset = Standard
+