Merge remote-tracking branch 'origin/1.5.1'

StaticData/PrinterSettings/3D Stuffmaker/Core/config.ini

@@ -3,28 +3,35 @@ bed_shape = rectangular
 bed_size = 215,215
 bed_temperature = 0
 bottom_clip_amount = 0
+bottom_solid_layers = 1mm
 bridge_acceleration = 0
 bridge_fan_speed = 100
 bridge_flow_ratio = 1
 bridge_speed = 15
 brim_width = 0
 build_height = 205
-cancel_gcode = G91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nG1 E-10 F500 ; Retract Extruder\nG90;\nG28 Y0;   Home Y axis\nG1 X215 F2000; bring plate to front\nM84;
-center_part_on_bed = 1
+cancel_gcode = G91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nG1 E-10 F500 ; Retract Extruder\nG90;\nG28 Y;   Home Y axis\nG1 X210 Y10 F2000; bring plate to front\nM84;
+center_part_on_bed = 0
 complete_objects = 0
+connect_gcode = 
 cool_extruder_lift = 0
+print_leveling_solution = 7 Point Disk
+print_leveling_method = Manual
+print_leveling_required_to_print = 1
+manual_probe_paper_width = .1
 cooling = 1
 create_raft = 1
 default_acceleration = 0
 disable_fan_first_layers = 0
-end_gcode = M104 T0 S0 ; turn off temperature\nM104 T1 S0 ; turn off temperature\nG91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nT0\nG1 E-15 F500 ; Retract Extruder\nT1\nG1 E-15 F500\nG28 Y0;\nG90;\nG1 X215 F2000 ; home X axis\nM84;
-external_perimeter_speed = 25
+end_gcode = M104 T0 S0 ; turn off temperature\nM104 T1 S0 ; turn off temperature\nG91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nT0\nG1 E-40 F800 ; Retract Extruder\nT1\nG1 E-40 F800\nG90;\nG1 X210 Y10 F2000;\nM84;
+external_perimeter_speed = 30
 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20
 extruder_clearance_radius = 20
 extruder_count = 2
-extruder_offset = 0x0,32.75x-0.4,0x0,0x0
+extruder_offset = 0x0,31.55x-0.3,0x0,0x0
+extruder_wipe_temperature = 0
 extruders_share_temperature = 0
 extrusion_axis = E
 extrusion_multiplier = 1
@@ -32,13 +39,14 @@ extrusion_width = 0
 fan_always_on = 0
 fan_below_layer_time = 60
 filament_diameter = 1.79
-fill_angle = 20
-fill_density = 45%
+fill_angle = 45
+fill_density = 10%
 fill_pattern = honeycomb
 first_layer_acceleration = 0
 first_layer_bed_temperature = 75
+first_layer_extrusion_width = 100%
 first_layer_height = 0.15
-first_layer_speed = 22
+first_layer_speed = 20
 first_layer_temperature = 205
 g0 = 0
 gap_fill_speed = 20
@@ -49,67 +57,71 @@ gcode_output_type = REPRAP
 has_fan = 1
 has_hardware_leveling = 0
 has_heated_bed = 0
+has_power_control = 0
 has_sd_card_reader = 1
-heat_extruder_before_homing = 0
+show_reset_connection = 1
+heat_extruder_before_homing = 1
 infill_acceleration = 0
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0
 infill_first = 0
 infill_only_where_needed = 0
-infill_overlap_perimeter = .06
-infill_speed = 20
+infill_overlap_perimeter = 0
+infill_speed = 30
 infill_type = LINES
 layer_gcode = 
-layer_height = 0.2
+layer_height = 0.35
 max_fan_speed = 100
-min_extrusion_before_retract = .1
-min_fan_speed = 70
-min_print_speed = 9
-min_skirt_length = 2
+min_extrusion_before_retract = 0.003
+min_fan_speed = 80
+min_print_speed = 7
+min_skirt_length = 3
 notes = 
-nozzle_diameter = 0.45
+nozzle_diameter = 0.48
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base].gcode
 overhangs = 1
-pause_gcode = G1 X0 Y0 F2000; home axes\nM84 S0
+pause_gcode = G1 X0 Y215 F2000; home axes\nM84 S0
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0
-perimeter_speed = 25
+perimeter_speed = 30
 perimeters = 3
 post_process = 
-print_center = 105,105
-raft_air_gap = 0.3
-raft_extruder = 0
+print_center = 110,110
+raft_air_gap = 0.25
+raft_extruder = 1
 raft_extra_distance_around_part = 5
-raft_fan_speed_percent = 75
+raft_fan_speed_percent = 40
 raft_layers = 0
-raft_print_speed = 25
+raft_print_speed = 35
+bed_remove_part_temperature = 0
 randomize_start = 0
 repair_outlines_extensive_stitching = 1
-repair_outlines_keep_open = 0
+repair_outlines_keep_open = 1
 resolution = 0
 resume_gcode = 
-retract_before_travel = 3
+retract_before_travel = 4
 retract_layer_change = 1
 retract_length = 1
-retract_length_tool_change = 3
-retract_lift = 0.06
+retract_length_tool_change = 25
+retract_lift = 0.35
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
-retract_speed = 25
-skirt_distance = 0.7
+retract_speed = 15
+skirt_distance = 2
 skirt_height = 1
 skirts = 3
-slowdown_below_layer_time = 8
+slowdown_below_layer_time = 20
 small_perimeter_speed = 30
 solid_fill_pattern = rectilinear
 solid_infill_below_area = 70
 solid_infill_every_layers = 0
 solid_infill_extrusion_width = 0
 solid_infill_speed = 60
+solid_shell = 0
 spiral_vase = 0
 standby_temperature_delta = -5
 start_gcode = M42 P5 S128\nG28 X0 Y0 ; home all axes\nM106 S160\nG28 X0 Y0 Z0\nG91\nG1 Z5 F3000\nT0\nG1 E35 F100 ;  Extrude primer filament\nT1\nG1 E35 F100\nT0\nG1 Z5 F3000
@@ -121,13 +133,13 @@ support_material_create_internal_support = 1
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 100%
-support_material_infill_angle = 45
+support_material_infill_angle = 90
 support_material_interface_extruder = 1
-support_material_interface_layers = 4
+support_material_interface_layers = 1mm
 support_material_interface_spacing = 0
 support_material_pattern = honeycomb
 support_material_spacing = 2.5
-support_material_speed = 25
+support_material_speed = 35
 support_material_threshold = 20
 support_material_xy_distance = 0.7
 support_material_z_distance = 0.15
@@ -139,13 +151,13 @@ threads = 2
 toolchange_gcode = 
 top_infill_extrusion_width = 0
 top_solid_infill_speed = 50
-top_solid_layers = 1mm
-travel_speed = 70
+top_solid_layers = 1.4mm
+travel_speed = 95
 use_firmware_retraction = 0
 use_relative_e_distances = 0
 vibration_limit = 0
-wipe = 0
+wipe = 1
 wipe_shield_distance = 0
 wipe_tower_size = 0
 z_can_be_negative = 0
-z_offset = 0
+z_offset = -0.2

StaticData/PrinterSettings/3D Stuffmaker/Core/quality/High [Dual Material].slice

@@ -1,7 +1,10 @@
-layer_height = 0.15
-wipe_shield_distance = 4
-wipe_tower_size = 8
+layer_height = 0.1
+wipe_tower_size = 12
 support_material_extruder = 1
 support_material_interface_extruder = 2
-raft_extruder = 1
-start_gcode = M42 P5 S128\nG28 X0 Y0 ; home all axes\nM106 S160\nG28 X0 Y0 Z0\nG91\nG1 Z5 F3000\nT0\nG1 E35 F100 ;  Extrude primer filament\nT1\nG1 E35 F100\nT0\nG1 Z5 F3000
+raft_extruder = 2
+start_gcode = ;== Enable illumination ===================\nM42 P5 S128\n;== Home Axes =============================\nG90; Set to absolute mode\nG28 X Y\n;== Start cooling fan =====================\nM106 S160\n;== Start AutoTemp ========================\nM109 T0 S[temperature] B260 F1\nM109 T1 S210 B260 F1\n;== Move the Z axis =======================\nG91\nG1 Z25 F5000\nG90\n;== Move X,Y to primer position ===========\nG1 X0 Y10 F5000\n;== Set Extruder relative mode & prime==\nT0\nM83 \nG1 E60 F175 ;  Extrude\nG1 E-2 F5000 ; Retract\nM82\nT1\nM83 \nG1 E60 F175 ;  Extrude\nG1 E-2 F5000 ; Retract\nM82\nT0\n;== Reset extruder value (X,Y,Z,E)======\nG92 E0;\n;== Move the Z axis (faster) ==============\nG91\nG1 Z5 F20000 ; \nG90\n;== Home Axes =============================\nG28 X Y Z ; Home Axes\n;== Move the Z axis ==============\nG91\nG1 Z10 F5000 ; Move Z axis\nG90
+raft_extra_distance_around_part = 4
+bridge_speed = 18
+retract_lift = 0.4
+end_gcode = M104 T0 S0 ; turn off temperature\nM104 T1 S0 ; turn off temperature\nM106 S0 ;  Turn off Fan\nG91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nT0\nG1 E-30 F800 ; Retract Extruder\nT1\nG1 E-30 F800\nG90;\nG1 X210 Y10 F3000;\nM84;

StaticData/PrinterSettings/3D Stuffmaker/Core/quality/High [Single Material].slice

@@ -1,2 +1,5 @@
-layer_height = 0.15
-start_gcode = M42 P5 S128\nG28 X0 Y0 ; home all axes\nM106 S160\nG28 X0 Y0 Z0\nG91\nG1 Z5 F3000\nT0\nG1 E35 F100 ;  Extrude primer filament\nT1\nG1 E35 F100\nT0
+layer_height = 0.1
+start_gcode = ;== Enable illumination ===================\nM42 P5 S128\n;== Home Axes =============================\nG90; Set to absolute mode\nG28 X Y\n;== Start cooling fan =====================\nM106 S160\n;== Start AutoTemp ========================\nM109 T0 S[temperature] B260 F1 \n;== Move the Z axis =======================\nG91\nG1 Z25 F5000\nG90\n;== Move X,Y to primer position ===========\nG1 X0 Y10 F5000\n;== Set Extruder relative mode & prime==\nT0\nM83 \nG1 E60 F175 ;  Extrude\nG1 E-2 F5000 ; Retract\nM82\n;== Reset extruder value (X,Y,Z,E)======\nG92 E0;\n;== Move the Z axis (faster) ==============\nG91\nG1 Z5 F20000 ; \nG90\n;== Home Axes =============================\nG28 X Y Z ; Home Axes\n;== Move the Z axis ==============\nG91\nG1 Z10 F5000 ; Move Z axis\nG90
+bridge_speed = 18
+retract_lift = 0.4
+end_gcode = M104 T0 S0 ; turn off temperature\nM104 T1 S0 ; turn off temperature\nM106 S0 ;  Turn off Fan\nG91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nT0\nG1 E-30 F800 ; Retract Extruder\nG90;\nG1 X210 Y10 F3000;\nM84;

StaticData/PrinterSettings/3D Stuffmaker/Core/quality/Standard [Dual Material].slice

@@ -1,7 +1,10 @@
 layer_height = 0.2
-wipe_shield_distance = 4
-wipe_tower_size = 8
+wipe_tower_size = 12
 support_material_extruder = 1
 support_material_interface_extruder = 2
-raft_extruder = 1
-start_gcode = M42 P5 S128\nG28 X0 Y0 ; home all axes\nM106 S160\nG28 X0 Y0 Z0\nG91\nG1 Z5 F3000\nT0\nG1 E35 F100 ;  Extrude primer filament\nT1\nG1 E35 F100\nT0\nG1 Z5 F3000
+raft_extruder = 2
+start_gcode = ;== Enable illumination ===================\nM42 P5 S128\n;== Home Axes =============================\nG90; Set to absolute mode\nG28 X Y\n;== Start cooling fan =====================\nM106 S160\n;== Start AutoTemp ========================\nM109 T0 S[temperature] B260 F2\nM109 T1 S210 B260 F2 \n;== Move the Z axis =======================\nG91\nG1 Z25 F5000\nG90\n;== Move X,Y to primer position ===========\nG1 X0 Y10 F5000\n;== Set Extruder relative mode & prime==\nT0\nM83 \nG1 E60 F175 ;  Extrude\nG1 E-2 F5000 ; Retract\nM82\nT1\nM83 \nG1 E60 F175 ;  Extrude\nG1 E-2 F5000 ; Retract\nM82\nT0\n;== Reset extruder value (X,Y,Z,E)======\nG92 E0;\n;== Move the Z axis (faster) ==============\nG91\nG1 Z5 F20000 ; \nG90\n;== Home Axes =============================\nG28 X Y Z ; Home Axes\n;== Move the Z axis ==============\nG91\nG1 Z10 F5000 ; Move Z axis\nG90
+raft_extra_distance_around_part = 4
+bridge_speed = 21
+retract_lift = 0.4
+end_gcode = M104 T0 S0 ; turn off temperature\nM104 T1 S0 ; turn off temperature\nM106 S0 ;  Turn off Fan\nG91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nT0\nG1 E-30 F800 ; Retract Extruder\nT1\nG1 E-30 F800\nG90;\nG1 X210 Y10 F3000;\nM84;

StaticData/PrinterSettings/3D Stuffmaker/Core/quality/Standard [Single Material].slice

@@ -1,2 +1,5 @@
 layer_height = 0.2
-start_gcode = M42 P5 S128\nG28 X0 Y0 ; home all axes\nM106 S160\nG28 X0 Y0 Z0\nG91\nG1 Z5 F3000\nT0\nG1 E35 F100 ;  Extrude primer filament\nT1\nG1 E35 F100\nT0
+start_gcode = ;== Enable illumination ===================\nM42 P5 S128\n;== Home Axes =============================\nG90; Set to absolute mode\nG28 X Y\n;== Start cooling fan =====================\nM106 S160\n;== Start AutoTemp ========================\nM109 T0 S[temperature] B260 F2 \n;== Move the Z axis =======================\nG91\nG1 Z25 F5000\nG90\n;== Move X,Y to primer position ===========\nG1 X0 Y10 F5000\n;== Set Extruder relative mode & prime==\nT0\nM83 \nG1 E60 F175 ;  Extrude\nG1 E-2 F5000 ; Retract\nM82\n;== Reset extruder value (X,Y,Z,E)======\nG92 E0;\n;== Move the Z axis (faster) ==============\nG91\nG1 Z5 F20000 ; \nG90\n;== Home Axes =============================\nG28 X Y Z ; Home Axes\n;== Move the Z axis ==============\nG91\nG1 Z10 F5000 ; Move Z axis\nG90
+bridge_speed = 21
+retract_lift = 0.4
+end_gcode = M104 T0 S0 ; turn off temperature\nM104 T1 S0 ; turn off temperature\nM106 S0 ;  Turn off Fan\nG91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nT0\nG1 E-30 F800 ; Retract Extruder\nG90;\nG1 X210 Y10 F3000;\nM84;

StaticData/PrinterSettings/3D Stuffmaker/Creator/config.ini

@@ -1,47 +1,55 @@
 avoid_crossing_perimeters = 1
 bed_shape = rectangular
-bed_size = 102,160
+bed_size = 95,155
 bed_temperature = 0
 bottom_clip_amount = 0
-bridge_acceleration = 500
+bottom_solid_layers = 1.2mm
+bridge_acceleration = 0
 bridge_fan_speed = 100
-bridge_flow_ratio = 0.9
-bridge_speed = 20
-brim_width = 1
-build_height = 105
-cancel_gcode = G91\nG1 Z5 F300\nG90\nG28 X0 ; home X axes\nG1 Y150 F3000 ; Bring print bed to front of Printer\nG91\nG1 E-10 150 ; Retract Extruder\nG90; \nM84;
-center_part_on_bed = 1
+bridge_flow_ratio = 0.8
+bridge_speed = 40
+brim_width = 0.5
+build_height = 110
+cancel_gcode = G91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nG1 E-10 F500 ; Retract Extruder\nG90;\nG28 X0;   Home X axis\nG1 Y155 F3000; bring plate to front\nM84;
+center_part_on_bed = 0
 complete_objects = 1
+connect_gcode = 
 cool_extruder_lift = 0
+print_leveling_solution = 3 Point Plane
+print_leveling_method = Manual
+print_leveling_required_to_print = 1
+manual_probe_paper_width = .1
 cooling = 1
 create_raft = 1
-default_acceleration = 1200
+default_acceleration = 0
 disable_fan_first_layers = 1
-end_gcode = M104 S0 ; turn off temperature\nG91\nG1 Z5 F300\nG90\nG28 X0 ; home X axes\nG1 Y225 F3000 ; Bring print bed to front of Printer\nG91\nG1 E-10 150 ; Retract Extruder\nG90; \nM84;
-external_perimeter_speed = 24
+end_gcode = M104 S0 ; turn off temperature\nG91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nG1 E-15 F500 ; Retract Extruder\nG90;\nG28 X0  ; home X axis\nG1 Y225 F3000; bring plate to front\nM84;
+external_perimeter_speed = 40
 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 35
 extruder_clearance_radius = 40
 extruder_count = 1
 extruder_offset = 0x0
+extruder_wipe_temperature = 0
 extruders_share_temperature = 0
 extrusion_axis = E
-extrusion_multiplier = 1.0
-extrusion_width = 0.7
-fan_always_on = 1
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 0
 fan_below_layer_time = 60
-filament_diameter = 1.75
-fill_angle = 45
-fill_density = 45%
-fill_pattern = honeycomb
-first_layer_acceleration = 1200
+filament_diameter = 1.74
+fill_angle = 90
+fill_density = 10%
+fill_pattern = rectilinear
+first_layer_acceleration = 0
 first_layer_bed_temperature = 0
+first_layer_extrusion_width = 110%
 first_layer_height = 0.15
-first_layer_speed = 22
-first_layer_temperature = 215
+first_layer_speed = 20
+first_layer_temperature = 210
 g0 = 0
-gap_fill_speed = 10
+gap_fill_speed = 15
 gcode_arcs = 0
 gcode_comments = 1
 gcode_flavor = reprap
@@ -49,98 +57,108 @@ gcode_output_type = REPRAP
 has_fan = 0
 has_hardware_leveling = 0
 has_heated_bed = 0
+has_power_control = 0
 has_sd_card_reader = 0
+show_reset_connection = 1
 heat_extruder_before_homing = 1
-infill_acceleration = 200
+infill_acceleration = 0
 infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0
-infill_first = 1
-infill_only_where_needed = 0
-infill_overlap_perimeter = .06
-infill_speed = 24
+infill_first = 0
+infill_only_where_needed = 1
+infill_overlap_perimeter = 0
+infill_speed = 40
 infill_type = LINES
 layer_gcode = 
 layer_height = 0.3
+layer_to_pause = 
 max_fan_speed = 100
-min_extrusion_before_retract = .1
+min_extrusion_before_retract = 0.003
 min_fan_speed = 35
-min_print_speed = 9
+min_print_speed = 3
 min_skirt_length = 2
 notes = 
 nozzle_diameter = 0.75
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base].gcode
-overhangs = 
-pause_gcode = G1 X0 Y0 F3000\nM84 S0\n
-perimeter_acceleration = 900
+overhangs = 1
+pause_gcode = G1 X0 Y0 F3000; home all axes\nM84 S0
+perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0
-perimeter_speed = 24
+external_perimeter_extrusion_width = 100%
+perimeter_speed = 40
 perimeters = 3
 post_process = 
-print_center = 50,85
-raft_air_gap = 0.45
+print_center = 46,80
+raft_air_gap = 0.375
 raft_extruder = 0
-raft_extra_distance_around_part = 5
-raft_fan_speed_percent = 70
+raft_extra_distance_around_part = 4
+raft_fan_speed_percent = 100
 raft_layers = 0
-raft_print_speed = 24
+raft_print_speed = 20
+bed_remove_part_temperature = 0
 randomize_start = 1
-repair_outlines_extensive_stitching = 1
-repair_outlines_keep_open = 0
+repair_outlines_extensive_stitching = 0
+repair_outlines_keep_open = 1
 resolution = 0
 resume_gcode = 
 retract_before_travel = 3
 retract_layer_change = 0
-retract_length = 1
+retract_length = 0.5
 retract_length_tool_change = 10
-retract_lift = 0.06
+retract_lift = 0.4
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
+retract_when_changing_islands = 1
 retract_speed = 25
 skirt_distance = 0.7
 skirt_height = 2
 skirts = 3
-slowdown_below_layer_time = 8
-small_perimeter_speed = 30
+slowdown_below_layer_time = 20
+small_perimeter_speed = 10
 solid_fill_pattern = concentric
 solid_infill_below_area = 70
 solid_infill_every_layers = 20
 solid_infill_extrusion_width = 0
-solid_infill_speed = 70%
+solid_infill_speed = 90%
+solid_shell = 0
 spiral_vase = 0
 standby_temperature_delta = -5
-start_gcode = G28 X0 Y0 ; home all axes\nG1 Z2 F300\nG91;\nG1 E25 F150; Extruder primer filament
-start_perimeters_at_concave_points = 0
-start_perimeters_at_non_overhang = 0
+start_gcode = M92 X 31.6900 Y31.5515 Z1283 E70.770\nM205 X40\nG28 ; home all axes\nG91\nG1 E30 F100 ;  Extrude primer filament\nG90\nM109 S208 B250 F0.5
+start_perimeters_at_concave_points = 1
+start_perimeters_at_non_overhang = 1
+support_air_gap = .3
 support_material = 0
 support_material_angle = 45
-support_material_create_internal_support = 1
+support_material_percent = 50
+support_material_create_internal_support = 0
+support_material_create_perimeter = 1
 support_material_enforce_layers = 0
 support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_infill_angle = 90
+support_material_extrusion_width = 100%
+support_material_infill_angle = 45
 support_material_interface_extruder = 1
-support_material_interface_layers = 2
-support_material_interface_spacing = 2.5
+support_material_interface_layers = 1.5mm
+support_material_interface_spacing = 0
 support_material_pattern = honeycomb
-support_material_spacing = 2.5
-support_material_speed = 24
-support_material_threshold = 25
-support_material_xy_distance = 0.8
+support_material_spacing = 2
+support_material_speed = 30
+support_material_threshold = 30
+support_material_xy_distance = 3.25
 support_material_z_distance = 0.15
-support_material_z_gap_layers = 4
+support_material_z_gap_layers = 0.9mm
 support_type = LINES
-temperature = 200
+temperature = 208
 thin_walls = 1
 threads = 2
 toolchange_gcode = 
-top_infill_extrusion_width = 0.5
-top_solid_infill_speed = 50
-top_solid_layers = 1mm
-travel_speed = 105
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 25
+top_solid_layers = 1.2mm
+travel_speed = 95
 use_firmware_retraction = 0
 use_relative_e_distances = 0
 vibration_limit = 0
@@ -148,4 +166,4 @@ wipe = 1
 wipe_shield_distance = 0
 wipe_tower_size = 0
 z_can_be_negative = 0
-z_offset = 0
+z_offset = 0

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/High [Default with Supports].slice

@@ -0,0 +1,8 @@
+layer_height = 0.15
+support_material = 1
+bridge_speed = 6
+extrusion_multiplier = 1
+infill_speed = 30
+perimeter_speed = 30
+external_perimeter_speed = 30
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F1\nM83\nG1 E30 F100 ;  Extrude primer filament\nM82

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/High [Default].slice

@@ -1 +1,7 @@
-layer_height = 0.15
+layer_height = 0.15
+bridge_speed = 6
+extrusion_multiplier = 1
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F1\nM83\nG1 E30 F100 ;  Extrude primer filament\nM82
+infill_speed = 30
+perimeter_speed = 30
+external_perimeter_speed = 30

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/High [No infill with Supports].slice

@@ -0,0 +1,9 @@
+layer_height = 0.15
+fill_density = 0
+support_material = 1
+bridge_speed = 6
+extrusion_multiplier = 1
+infill_speed = 30
+perimeter_speed = 30
+external_perimeter_speed = 30
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F1\nM83\nG1 E30 F100 ;  Extrude primer filament\nM82

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/High [No infill].slice

@@ -0,0 +1,9 @@
+layer_height = 0.15
+fill_density = 0
+bridge_speed = 6
+extrusion_multiplier = 1
+infill_speed = 30
+perimeter_speed = 30
+external_perimeter_speed = 30
+min_print_speed = 22
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F1\nM83\nG1 E30 F100 ;  Extrude primer filament\nM82

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/High [no infill-hollow].slice

@@ -1,2 +0,0 @@
-layer_height = 0.15
-fill_density = 0

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/High [with support structure].slice

@@ -1,2 +0,0 @@
-layer_height = 0.15
-support_material = 1

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/Standard [Default with Supports].slice

@@ -0,0 +1,7 @@
+layer_height = 0.25
+support_material = 1
+infill_speed = 30
+perimeter_speed = 30
+external_perimeter_speed = 30
+bridge_speed = 35
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F2\nM83\nG1 E30 F100 ;  Extrude primer filament\nM82

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/Standard [Default].slice

@@ -1 +1,6 @@
-layer_height = 0.25
+layer_height = 0.25
+infill_speed = 30
+perimeter_speed = 30
+external_perimeter_speed = 30
+bridge_speed = 35
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F2\nM83\nG1 E30 F100 ;  Extrude primer filament\nM82

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/Standard [No infill with Supports].slice

@@ -0,0 +1,8 @@
+layer_height = 0.25
+fill_density = 0
+support_material = 1
+infill_speed = 30
+perimeter_speed = 30
+external_perimeter_speed = 30
+bridge_speed = 35
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F2\nM83\nG1 E30 F100 ;  Extrude primer filament\nM82

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/Standard [No infill].slice

@@ -0,0 +1,7 @@
+layer_height = 0.25
+fill_density = 0
+infill_speed = 30
+perimeter_speed = 30
+external_perimeter_speed = 30
+bridge_speed = 35
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F2\nM83\nG1 E30 F100 ;  Extrude primer filament\nM82

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/Standard [no infill-hollow].slice

@@ -1,2 +0,0 @@
-layer_height = 0.25
-fill_density = 0

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/Standard [with support structure].slice

@@ -1,2 +0,0 @@
-layer_height = 0.25
-support_material = 1

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/Super High [Default].slice

@@ -1 +0,0 @@
-layer_height = 0.09

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/Super High [no infill-hollow].slice

@@ -1,2 +0,0 @@
-layer_height = 0.09
-fill_density = 0

StaticData/PrinterSettings/3D Stuffmaker/Creator/quality/Super High [with support structure].slice

@@ -1,2 +0,0 @@
-layer_height = 0.09
-support_material = 1

StaticData/PrinterSettings/3D Stuffmaker/Evolution/config.ini

@@ -3,42 +3,50 @@ bed_shape = rectangular
 bed_size = 230,230
 bed_temperature = 0
 bottom_clip_amount = 0
+bottom_solid_layers = 2mm
 bridge_acceleration = 0
 bridge_fan_speed = 100
 bridge_flow_ratio = 0.8
-bridge_speed = 20
+bridge_speed = 30
 brim_width = 0.5
 build_height = 200
 cancel_gcode = G91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nG1 E-10 F500 ; Retract Extruder\nG90;\nG28 X0;   Home X axis\nG1 Y225 F3000; bring plate to front\nM84;
-center_part_on_bed = 1
+center_part_on_bed = 0
 complete_objects = 1
+connect_gcode = 
 cool_extruder_lift = 0
+print_leveling_solution = 7 Point Disk
+print_leveling_method = Manual
+print_leveling_required_to_print = 1
+manual_probe_paper_width = .1
 cooling = 1
 create_raft = 1
 default_acceleration = 0
 disable_fan_first_layers = 1
-end_gcode = M104 S0 ; turn off temperature\nG91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nG1 E-10 F500 ; Retract Extruder\nG90;\nG28 X0  ; home X axis\nG1 Y225 F3000; bring plate to front\nM84;
-external_perimeter_speed = 24
+end_gcode = M104 S0 ; turn off temperature\nG91 ;  Set distance mode to relative value mode\nG1 Z5 F5000 ; lift nozzle\nG1 E-15 F500 ; Retract Extruder\nG90;\nG28 X0  ; home X axis\nG1 Y225 F3000; bring plate to front\nM84;
+external_perimeter_speed = 30
 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 35
 extruder_clearance_radius = 40
 extruder_count = 1
 extruder_offset = 0x0
+extruder_wipe_temperature = 0
 extruders_share_temperature = 0
 extrusion_axis = E
-extrusion_multiplier = 1.0
+extrusion_multiplier = 1
 extrusion_width = 0
 fan_always_on = 0
 fan_below_layer_time = 60
 filament_diameter = 1.74
 fill_angle = 45
-fill_density = 0.45
+fill_density = 50%
 fill_pattern = rectilinear
 first_layer_acceleration = 0
 first_layer_bed_temperature = 0
+first_layer_extrusion_width = 110%
 first_layer_height = 0.15
-first_layer_speed = 25
+first_layer_speed = 20
 first_layer_temperature = 210
 g0 = 0
 gap_fill_speed = 15
@@ -46,10 +54,12 @@ gcode_arcs = 0
 gcode_comments = 1
 gcode_flavor = reprap
 gcode_output_type = REPRAP
-has_fan = 1
+has_fan = 0
 has_hardware_leveling = 0
 has_heated_bed = 0
+has_power_control = 0
 has_sd_card_reader = 0
+show_reset_connection = 1
 heat_extruder_before_homing = 1
 infill_acceleration = 0
 infill_every_layers = 1
@@ -57,18 +67,18 @@ infill_extruder = 1
 infill_extrusion_width = 0
 infill_first = 0
 infill_only_where_needed = 1
-infill_overlap_perimeter = .06
-infill_speed = 24
+infill_overlap_perimeter = 0
+infill_speed = 30
 infill_type = LINES
 layer_gcode = 
 layer_height = 0.3
 max_fan_speed = 100
-min_extrusion_before_retract = 0.1
+min_extrusion_before_retract = 0.003
 min_fan_speed = 35
-min_print_speed = 9
+min_print_speed = 14
 min_skirt_length = 2
 notes = 
-nozzle_diameter = 0.45
+nozzle_diameter = 0.55
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base].gcode
@@ -77,61 +87,63 @@ pause_gcode = G1 X0 Y0 F3000; home all axes\nM84 S0
 perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0
-perimeter_speed = 24
+perimeter_speed = 30
 perimeters = 3
 post_process = 
 print_center = 120,130
 raft_air_gap = 0.3
 raft_extruder = 0
-raft_extra_distance_around_part = 8
+raft_extra_distance_around_part = 4
 raft_fan_speed_percent = 100
 raft_layers = 0
-raft_print_speed = 24
+raft_print_speed = 30
+bed_remove_part_temperature = 0
 randomize_start = 1
-repair_outlines_extensive_stitching = 1
-repair_outlines_keep_open = 0
+repair_outlines_extensive_stitching = 0
+repair_outlines_keep_open = 1
 resolution = 0
 resume_gcode = 
 retract_before_travel = 3
 retract_layer_change = 0
 retract_length = 1
 retract_length_tool_change = 10
-retract_lift = 0.06
+retract_lift = 0.4
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
 retract_speed = 25
 skirt_distance = 0.7
 skirt_height = 2
 skirts = 3
-slowdown_below_layer_time = 8
+slowdown_below_layer_time = 20
 small_perimeter_speed = 10
 solid_fill_pattern = concentric
 solid_infill_below_area = 70
 solid_infill_every_layers = 20
 solid_infill_extrusion_width = 0
 solid_infill_speed = 90%
+solid_shell = 0
 spiral_vase = 0
 standby_temperature_delta = -5
-start_gcode = G28 X0 Y0 Z0; home all axes\nG91\nG1 E30 F100 ;  Extrude primer filament
+start_gcode = M92 X 31.6900 Y31.5515 Z1283 E70.770\nM205 X40\nG28 ; home all axes\nG91\nG1 E30 F100 ;  Extrude primer filament\nG90\nM109 S208 B250 F0.5
 start_perimeters_at_concave_points = 1
 start_perimeters_at_non_overhang = 1
-support_material = 1
+support_material = 0
 support_material_angle = 45
 support_material_create_internal_support = 0
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 100%
-support_material_infill_angle = 45
+support_material_infill_angle = 60
 support_material_interface_extruder = 1
-support_material_interface_layers = 2
+support_material_interface_layers = 1.5mm
 support_material_interface_spacing = 0
 support_material_pattern = honeycomb
-support_material_spacing = 2.5
-support_material_speed = 24
-support_material_threshold = 25
-support_material_xy_distance = 0.8
+support_material_spacing = 2
+support_material_speed = 30
+support_material_threshold = 20
+support_material_xy_distance = 3.25
 support_material_z_distance = 0.15
-support_material_z_gap_layers = 4
+support_material_z_gap_layers = 0.6mm
 support_type = LINES
 temperature = 208
 thin_walls = 1
@@ -139,8 +151,8 @@ threads = 2
 toolchange_gcode = 
 top_infill_extrusion_width = 0
 top_solid_infill_speed = 35
-top_solid_layers = 1mm
-travel_speed = 95
+top_solid_layers = 2mm
+travel_speed = 120
 use_firmware_retraction = 0
 use_relative_e_distances = 0
 vibration_limit = 0
@@ -148,4 +160,4 @@ wipe = 1
 wipe_shield_distance = 0
 wipe_tower_size = 0
 z_can_be_negative = 0
-z_offset = 0
+z_offset = 0

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/High [Default ].slice

@@ -0,0 +1,9 @@
+layer_height = 0.15
+bridge_speed = 6
+extrusion_multiplier = 1
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F1\nG91\nG1 E30 F100 ;  Extrude primer filament\nG1 Z3 F315 ; Raise the Z\nG90
+infill_speed = 40
+raft_print_speed = 40
+perimeter_speed = 40
+external_perimeter_speed = 40
+min_print_speed = 1

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/High [Default with supports].slice

@@ -0,0 +1,10 @@
+layer_height = 0.15
+support_material = 1
+bridge_speed = 6
+extrusion_multiplier = 1
+infill_speed = 32
+raft_print_speed = 32
+perimeter_speed = 32
+external_perimeter_speed = 32
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F1\nG91\nG1 E30 F100 ;  Extrude primer filament\nG1 Z3 F315 ; Raise the Z\nG90
+min_print_speed = 1

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/High [Default].slice

@@ -1 +0,0 @@
-layer_height = 0.15

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/High [No infill with supports].slice

@@ -0,0 +1,11 @@
+layer_height = 0.15
+fill_density = 0
+support_material = 1
+bridge_speed = 6
+extrusion_multiplier = 1
+infill_speed = 40
+raft_print_speed = 40
+perimeter_speed = 40
+external_perimeter_speed = 40
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F1\nG91\nG1 E30 F100 ;  Extrude primer filament\nG1 Z3 F315 ; Raise the Z\nG90
+min_print_speed = 1

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/High [No infill].slice

@@ -0,0 +1,10 @@
+layer_height = 0.15
+fill_density = 0
+bridge_speed = 6
+extrusion_multiplier = 1
+infill_speed = 40
+raft_print_speed = 40
+perimeter_speed = 40
+external_perimeter_speed = 40
+min_print_speed = 1
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F1\nG91\nG1 E30 F100 ;  Extrude primer filament\nG1 Z3 F315 ; Raise the Z\nG90

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/High [no infill-hollow].slice

@@ -1,2 +0,0 @@
-layer_height = 0.15
-fill_density = 0

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/High [with support structure].slice

@@ -1,2 +0,0 @@
-layer_height = 0.15
-support_material = 1

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/Standard [Default with supports].slice

@@ -0,0 +1,9 @@
+layer_height = 0.25
+support_material = 1
+infill_speed = 30
+raft_print_speed = 30
+perimeter_speed = 30
+external_perimeter_speed = 30
+bridge_speed = 30
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F2\nG91\nG1 E30 F100 ;  Extrude primer filament\nG1 Z3 F315 ; Raise the Z\nG90
+min_print_speed = 0.5

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/Standard [Default].slice

@@ -1 +1,8 @@
-layer_height = 0.25
+layer_height = 0.25
+infill_speed = 30
+raft_print_speed = 30
+perimeter_speed = 30
+external_perimeter_speed = 30
+bridge_speed = 30
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F2\nG91\nG1 E30 F175 ;  Extrude primer filament\nG1 Z3 F315 ; Raise the Z\nG90\n
+min_print_speed = 0.5

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/Standard [No infill with supports].slice

@@ -0,0 +1,10 @@
+layer_height = 0.25
+fill_density = 0
+support_material = 1
+infill_speed = 30
+raft_print_speed = 30
+perimeter_speed = 30
+external_perimeter_speed = 30
+bridge_speed = 30
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F2\nG91\nG1 E30 F100 ;  Extrude primer filament\nG1 Z3 F315 ; Raise the Z\nG90
+min_print_speed = 0.5

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/Standard [No infill].slice

@@ -0,0 +1,10 @@
+layer_height = 0.25
+fill_density = 0
+extrusion_multiplier = 1
+min_print_speed = 0.5
+start_gcode = G28 ; home all axes\nM109 S[temperature] B250 F2\nG91\nG1 E30 F100 ;  Extrude primer filament\nG1 Z3 F315 ; Raise the Z\nG90
+infill_speed = 30
+raft_print_speed = 30
+perimeter_speed = 30
+external_perimeter_speed = 30
+bridge_speed = 30

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/Standard [no infill-hollow].slice

@@ -1,2 +0,0 @@
-layer_height = 0.25
-fill_density = 0

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/Standard [with support structure].slice

@@ -1,2 +0,0 @@
-layer_height = 0.25
-support_material = 1

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/Super High [Default].slice

@@ -1 +0,0 @@
-layer_height = 0.09

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/Super High [no infill-hollow].slice

@@ -1,2 +0,0 @@
-layer_height = 0.09
-fill_density = 0

StaticData/PrinterSettings/3D Stuffmaker/Evolution/quality/Super High [with support structure].slice

@@ -1,2 +0,0 @@
-layer_height = 0.09
-support_material = 1

StaticData/PrinterSettings/3D Stuffmaker/Mega i3/config.ini

@@ -3,6 +3,7 @@ bed_shape = rectangular
 bed_size = 310,310
 bed_temperature = 0
 bottom_clip_amount = 0
+bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_fan_speed = 100
 bridge_flow_ratio = 0.8
@@ -37,6 +38,7 @@ fill_density = 0.2
 fill_pattern = rectilinear
 first_layer_acceleration = 0
 first_layer_bed_temperature = 0
+first_layer_extrusion_width = 100%
 first_layer_height = 0.25
 first_layer_speed = 25
 first_layer_temperature = 205
@@ -147,4 +149,4 @@ wipe = 1
 wipe_shield_distance = 0
 wipe_tower_size = 0
 z_can_be_negative = 0
-z_offset = 0
+z_offset = 0