final changes for IRA3D

StaticData/PrinterSettings/IRA3D/Poetry Infinity/config.ini

@@ -17,14 +17,14 @@ connect_gcode =
 cool_extruder_lift = 0
 print_leveling_solution = 3 Point Plane
 print_leveling_method = Manual
-print_leveling_required_to_print = 1
+print_leveling_required_to_print = 0
 manual_probe_paper_width = .1
 cooling = 1
 create_raft = 0
 default_acceleration = 0
 disable_fan_first_layers = 2
-end_gcode = M207 S300.0 F2400 Z0.075\nG28 X0 Y0\nG1 E-3.0 F5.0\nM104 S0\nM140 S0\nM84; disable motors 
-external_perimeter_speed = 100%
+end_gcode = M207 S300.0 F2400 Z0.075\nG28 X0 Y0\nG1 E-3.0 F5.0\nM104 S0\nM140 S0\nM84     ; disable motors
+external_perimeter_speed = 85%
 external_perimeters_first = 0
 extra_perimeters = 1
 extruder_clearance_height = 20
@@ -40,12 +40,12 @@ fan_always_on = 0
 fan_below_layer_time = 60
 filament_diameter = 1.75
 fill_angle = 60
-fill_density = 10%
+fill_density = 0.2
 fill_pattern = honeycomb
 first_layer_acceleration = 0
 first_layer_bed_temperature = 75
 first_layer_extrusion_width = 100%
-first_layer_height = 0.24
+first_layer_height = 0.25
 first_layer_speed = 25
 first_layer_temperature = 205
 g0 = 0
@@ -68,13 +68,13 @@ infill_extrusion_width = 0
 infill_first = 0
 infill_only_where_needed = 0
 infill_overlap_perimeter = 0.08
-infill_speed = 35
+infill_speed = 45
 infill_type = LINES
 layer_gcode = 
-layer_height = 0.08
+layer_height = 0.15
 layer_to_pause = 
 max_fan_speed = 90
-min_extrusion_before_retract = 0.02
+min_extrusion_before_retract = 0.1
 min_fan_speed = 50
 min_print_speed = 10
 min_skirt_length = 20
@@ -89,7 +89,7 @@ perimeter_acceleration = 0
 perimeter_extruder = 1
 perimeter_extrusion_width = 0
 external_perimeter_extrusion_width = 100%
-perimeter_speed = 25
+perimeter_speed = 35
 perimeters = 2
 post_process = 
 print_center = 131,120
@@ -98,22 +98,22 @@ raft_extruder = 1
 raft_extra_distance_around_part = 7
 raft_fan_speed_percent = 50
 raft_layers = 0
-raft_print_speed = 25
+raft_print_speed = 30
 bed_remove_part_temperature = 0
 randomize_start = 0
 repair_outlines_extensive_stitching = 0
 repair_outlines_keep_open = 1
 resolution = 0
 resume_gcode = 
-retract_before_travel = 30
+retract_before_travel = 1
 retract_layer_change = 1
-retract_length = 0
-retract_length_tool_change = 0
+retract_length = 3
+retract_length_tool_change = 10
 retract_lift = 0
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
 retract_when_changing_islands = 1
-retract_speed = 20
+retract_speed = 40
 skirt_distance = 0
 skirt_height = 1
 skirts = 1
@@ -127,13 +127,13 @@ solid_infill_speed = 60
 solid_shell = 0
 spiral_vase = 0
 standby_temperature_delta = -5
-start_gcode = G28; home all axes\nG1 Z45.0 F[travel_speed] ;move the platform down 15mmG1 E90 F250\nG1 E90 F250\nG92 E0\nG0 Z5 F5000 ;set warming position
+start_gcode = G28 ; home all axes \nG1 Z45.0 F150 ;move the platform down 15mmG1 E90 F250\nG1 E90 F250\nG92 E0\nG0 Z5 F5000 ;set warming position\n\n
 start_perimeters_at_concave_points = 0
 start_perimeters_at_non_overhang = 0
 support_air_gap = .3
 support_material = 0
 support_material_angle = 45
-support_material_percent = 50
+support_material_percent = 5
 support_material_create_internal_support = 0
 support_material_create_perimeter = 1
 support_material_enforce_layers = 0
@@ -150,20 +150,20 @@ support_material_threshold = 60
 support_material_xy_distance = 0.7
 support_material_z_distance = 0.15
 support_material_z_gap_layers = .3mm
-support_type = LINES
+support_type = GRID
 temperature = 220
 thin_walls = 1
 threads = 2
 toolchange_gcode = 
 top_infill_extrusion_width = 0
-top_solid_infill_speed = 50
+top_solid_infill_speed = 100%
 top_solid_layers = 1mm
-travel_speed = 130
+travel_speed = 150
 use_firmware_retraction = 0
 use_relative_e_distances = 0
 vibration_limit = 0
 wipe = 0
 wipe_shield_distance = 0
 wipe_tower_size = 0
-z_can_be_negative = 1
+z_can_be_negative = 0
 z_offset = 0

StaticData/PrinterSettings/IRA3D/Poetry Infinity/material/ABS Super.slice

@@ -4,13 +4,13 @@ temperature = 265
 extruder_wipe_temperature = 0
 bed_temperature = 100
 bed_remove_part_temperature = 0
-retract_length = 0
-retract_length_tool_change = 0
-retract_speed = 20
+retract_length = 3
+retract_length_tool_change = 10
+retract_speed = 40
 retract_lift = 0
 retract_restart_extra = 0
-retract_before_travel = 30
-min_extrusion_before_retract = 0.02
+retract_before_travel = 1
+min_extrusion_before_retract = 0.1
 wipe = 0
 first_layer_extrusion_width = 100%
 support_material_extrusion_width = 0

StaticData/PrinterSettings/IRA3D/Poetry Infinity/material/Cristal.slice

@@ -4,13 +4,13 @@ temperature = 240
 extruder_wipe_temperature = 0
 bed_temperature = 80
 bed_remove_part_temperature = 0
-retract_length = 0
-retract_length_tool_change = 0
-retract_speed = 20
+retract_length = 3
+retract_length_tool_change = 10
+retract_speed = 40
 retract_lift = 0
 retract_restart_extra = 0
-retract_before_travel = 30
-min_extrusion_before_retract = 0.02
+retract_before_travel = 1
+min_extrusion_before_retract = 0.1
 wipe = 0
 first_layer_extrusion_width = 100%
 support_material_extrusion_width = 0
@@ -20,4 +20,5 @@ bridge_fan_speed = 90
 disable_fan_first_layers = 2
 slowdown_below_layer_time = 5
 min_print_speed = 10
-cool_extruder_lift = 0
+cool_extruder_lift = 0
+skirt_distance = 2

StaticData/PrinterSettings/IRA3D/Poetry Infinity/material/Grafene 0.8 Nozzle.slice

@@ -4,13 +4,13 @@ temperature = 220
 extruder_wipe_temperature = 0
 bed_temperature = 50
 bed_remove_part_temperature = 0
-retract_length = 0
-retract_length_tool_change = 0
-retract_speed = 20
+retract_length = 3
+retract_length_tool_change = 10
+retract_speed = 40
 retract_lift = 0
 retract_restart_extra = 0
-retract_before_travel = 30
-min_extrusion_before_retract = 0.02
+retract_before_travel = 1
+min_extrusion_before_retract = 0.1
 wipe = 0
 first_layer_extrusion_width = 100%
 support_material_extrusion_width = 0
@@ -28,4 +28,5 @@ perimeter_speed = 25
 external_perimeter_speed = 25
 support_material_speed = 30
 travel_speed = 120
-create_raft = 0
+create_raft = 0
+skirt_distance = 2

StaticData/PrinterSettings/IRA3D/Poetry Infinity/material/Gummify.slice

@@ -4,13 +4,13 @@ temperature = 245
 extruder_wipe_temperature = 0
 bed_temperature = 30
 bed_remove_part_temperature = 0
-retract_length = 0
-retract_length_tool_change = 0
-retract_speed = 3
+retract_length = 3
+retract_length_tool_change = 10
+retract_speed = 40
 retract_lift = 0
 retract_restart_extra = 0
-retract_before_travel = 30
-min_extrusion_before_retract = 0.02
+retract_before_travel = 10
+min_extrusion_before_retract = 0.1
 wipe = 0
 first_layer_extrusion_width = 100%
 support_material_extrusion_width = 0
@@ -23,4 +23,5 @@ min_print_speed = 10
 cool_extruder_lift = 0
 infill_speed = 45
 perimeter_speed = 45
-create_raft = 0
+create_raft = 0
+skirt_distance = 2

StaticData/PrinterSettings/IRA3D/Poetry Infinity/material/H-Limofy.slice

@@ -4,13 +4,13 @@ temperature = 250
 extruder_wipe_temperature = 0
 bed_temperature = 50
 bed_remove_part_temperature = 0
-retract_length = 0
-retract_length_tool_change = 0
+retract_length = 3
+retract_length_tool_change = 10
 retract_speed = 20
 retract_lift = 0
 retract_restart_extra = 0
-retract_before_travel = 30
-min_extrusion_before_retract = 0.02
+retract_before_travel = 1
+min_extrusion_before_retract = 0.1
 wipe = 0
 first_layer_extrusion_width = 100%
 support_material_extrusion_width = 0

StaticData/PrinterSettings/IRA3D/Poetry Infinity/material/IRABronze.slice

@@ -4,13 +4,13 @@ temperature = 228
 extruder_wipe_temperature = 0
 bed_temperature = 45
 bed_remove_part_temperature = 0
-retract_length = 0
-retract_length_tool_change = 0
-retract_speed = 20
+retract_length = 3
+retract_length_tool_change = 10
+retract_speed = 40
 retract_lift = 0
 retract_restart_extra = 0
-retract_before_travel = 30
-min_extrusion_before_retract = 0.02
+retract_before_travel = 1
+min_extrusion_before_retract = 0.1
 wipe = 0
 first_layer_extrusion_width = 100%
 support_material_extrusion_width = 0

StaticData/PrinterSettings/IRA3D/Poetry Infinity/material/IRACarbonF 0.4 Nozzle.slice

@@ -4,13 +4,13 @@ temperature = 215
 extruder_wipe_temperature = 0
 bed_temperature = 60
 bed_remove_part_temperature = 0
-retract_length = 0
-retract_length_tool_change = 0
-retract_speed = 15
+retract_length = 3
+retract_length_tool_change = 10
+retract_speed = 40
 retract_lift = 0
 retract_restart_extra = 0
-retract_before_travel = 30
-min_extrusion_before_retract = 0.02
+retract_before_travel = 1
+min_extrusion_before_retract = 0.1
 wipe = 0
 first_layer_extrusion_width = 100%
 support_material_extrusion_width = 0
@@ -24,4 +24,5 @@ cool_extruder_lift = 0
 extruder_offset = 0x0,0x0,0x0,0x0
 nozzle_diameter = 0.4
 infill_speed = 35
-create_raft = 0
+create_raft = 0
+skirt_distance = 2

StaticData/PrinterSettings/IRA3D/Poetry Infinity/material/IRACarbonF 0.8 Nozzle.slice

@@ -4,13 +4,13 @@ temperature = 215
 extruder_wipe_temperature = 0
 bed_temperature = 60
 bed_remove_part_temperature = 0
-retract_length = 0
-retract_length_tool_change = 0
-retract_speed = 20
+retract_length = 3
+retract_length_tool_change = 10
+retract_speed = 40
 retract_lift = 0
 retract_restart_extra = 0
-retract_before_travel = 30
-min_extrusion_before_retract = 0.02
+retract_before_travel = 10
+min_extrusion_before_retract = 0.1
 wipe = 0
 first_layer_extrusion_width = 100%
 support_material_extrusion_width = 0
@@ -24,4 +24,5 @@ cool_extruder_lift = 0
 extruder_offset = 0x0,0x0,0x0,0x0
 nozzle_diameter = 0.8
 infill_speed = 35
-create_raft = 0
+create_raft = 0
+skirt_distance = 2

StaticData/PrinterSettings/IRA3D/Poetry Infinity/material/IRACopper.slice

@@ -4,13 +4,13 @@ temperature = 228
 extruder_wipe_temperature = 0
 bed_temperature = 45
 bed_remove_part_temperature = 0
-retract_length = 0
-retract_length_tool_change = 0
-retract_speed = 20
+retract_length = 3
+retract_length_tool_change = 10
+retract_speed = 40
 retract_lift = 0
 retract_restart_extra = 0
-retract_before_travel = 30
-min_extrusion_before_retract = 0.02
+retract_before_travel = 1
+min_extrusion_before_retract = 0.1
 wipe = 0
 first_layer_extrusion_width = 100%
 support_material_extrusion_width = 0

StaticData/PrinterSettings/IRA3D/Poetry Infinity/material/IRAPLA.slice

@@ -4,13 +4,13 @@ temperature = 220
 extruder_wipe_temperature = 0
 bed_temperature = 45
 bed_remove_part_temperature = 0
-retract_length = 0
-retract_length_tool_change = 0
-retract_speed = 20
+retract_length = 3
+retract_length_tool_change = 10
+retract_speed = 40
 retract_lift = 0
 retract_restart_extra = 0
-retract_before_travel = 30
-min_extrusion_before_retract = 0.02
+retract_before_travel = 1
+min_extrusion_before_retract = 0.1
 wipe = 0
 first_layer_extrusion_width = 100%
 support_material_extrusion_width = 0

StaticData/PrinterSettings/IRA3D/Poetry Infinity/material/IRAluminum.slice

@@ -4,13 +4,13 @@ temperature = 228
 extruder_wipe_temperature = 0
 bed_temperature = 45
 bed_remove_part_temperature = 0
-retract_length = 0
-retract_length_tool_change = 0
-retract_speed = 20
+retract_length = 3
+retract_length_tool_change = 10
+retract_speed = 40
 retract_lift = 0
 retract_restart_extra = 0
-retract_before_travel = 30
-min_extrusion_before_retract = 0.02
+retract_before_travel = 1
+min_extrusion_before_retract = 0.1
 wipe = 0
 first_layer_extrusion_width = 100%
 support_material_extrusion_width = 0

StaticData/PrinterSettings/IRA3D/Poetry Infinity/material/Idrovanish.slice

@@ -4,13 +4,13 @@ temperature = 225
 extruder_wipe_temperature = 0
 bed_temperature = 50
 bed_remove_part_temperature = 0
-retract_length = 0
-retract_length_tool_change = 0
+retract_length = 3
+retract_length_tool_change = 10
 retract_speed = 20
 retract_lift = 0
 retract_restart_extra = 0
-retract_before_travel = 30
-min_extrusion_before_retract = 0.02
+retract_before_travel = 1
+min_extrusion_before_retract = 0.1
 wipe = 0
 first_layer_extrusion_width = 100%
 support_material_extrusion_width = 0
@@ -24,4 +24,5 @@ cool_extruder_lift = 0
 infill_speed = 35
 travel_speed = 150
 support_material_speed = 35
-create_raft = 0
+create_raft = 0
+support_type = GRID

StaticData/PrinterSettings/IRA3D/Poetry Infinity/material/IraBrick.slice

@@ -4,13 +4,13 @@ temperature = 228
 extruder_wipe_temperature = 0
 bed_temperature = 60
 bed_remove_part_temperature = 0
-retract_length = 0
-retract_length_tool_change = 0
-retract_speed = 5
+retract_length = 3
+retract_length_tool_change = 10
+retract_speed = 20
 retract_lift = 0
 retract_restart_extra = 0
-retract_before_travel = 30
-min_extrusion_before_retract = 0.02
+retract_before_travel = 1
+min_extrusion_before_retract = 0.1
 wipe = 0
 first_layer_extrusion_width = 100%
 support_material_extrusion_width = 0
@@ -26,4 +26,5 @@ external_perimeter_speed = 25
 infill_speed = 30
 create_raft = 0
 support_material_speed = 35
-travel_speed = 70
+travel_speed = 70
+skirt_distance = 2

StaticData/PrinterSettings/IRA3D/Poetry Infinity/material/IraWood.slice

@@ -4,13 +4,13 @@ temperature = 230
 extruder_wipe_temperature = 0
 bed_temperature = 60
 bed_remove_part_temperature = 0
-retract_length = 0
-retract_length_tool_change = 0
-retract_speed = 5
+retract_length = 3
+retract_length_tool_change = 10
+retract_speed = 20
 retract_lift = 0
 retract_restart_extra = 0
-retract_before_travel = 30
-min_extrusion_before_retract = 0.02
+retract_before_travel = 1
+min_extrusion_before_retract = 0.1
 wipe = 0
 first_layer_extrusion_width = 100%
 support_material_extrusion_width = 0
@@ -22,4 +22,5 @@ slowdown_below_layer_time = 5
 min_print_speed = 10
 cool_extruder_lift = 0
 infill_speed = 35
-create_raft = 0
+create_raft = 0
+skirt_distance = 2