Merge remote-tracking branch 'Chaz/master' into development

StaticData/OEMSettings/PrinterSettingsWhitelist.txt

@@ -5,4 +5,7 @@ SeeMeCNC
 Printrbot
 Deezmaker
 Blue Eagle Labs
-RoBo 3D
+RoBo 3D
+Solidoodle
+Portabee
+Lulzbot

StaticData/PrinterSettings/Lulzbot/TAZ ABS/config.ini

@@ -0,0 +1,114 @@
+avoid_crossing_perimeters = 0
+bed_size = 298,275
+bed_temperature = 85
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+build_height = 250
+complete_objects = 0
+cooling = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid =  1,1
+end_gcode =  M104 S0 ; turn off temperature\nG1 X10 Y200\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_offset =  0x0
+extrusion_axis =  E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_diameter = 3
+fill_angle = 45
+fill_density = 0.3
+fill_pattern =  rectilinear
+first_layer_bed_temperature = 85
+first_layer_extrusion_width = 200%
+first_layer_height = 0.25
+first_layer_speed = 30%
+first_layer_temperature = 230
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor =  reprap
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_gcode =  
+layer_height = 0.2
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 5
+notes =  
+nozzle_diameter = 0.35
+only_retract_when_crossing_perimeters = 0
+output_filename_format =  [input_filename_base].gcode
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process =  
+print_center =  149,137.5
+raft_layers = 0
+randomize_start = 1
+resolution = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 3
+retract_length_toolchange = 10
+retract_lift = 1
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 30
+small_perimeter_speed = 35
+solid_fill_pattern =  rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+start_gcode =  G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle
+support_material = 1
+support_material_angle = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_pattern =  rectilinear
+support_material_spacing = 3
+support_material_speed = 60
+support_material_threshold = 30
+temperature = 230
+threads = 2
+toolchange_gcode =  
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 3
+travel_speed = 150
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0

StaticData/PrinterSettings/Lulzbot/TAZ ABS/setup.ini

@@ -0,0 +1 @@
+baud_rate = 250000

StaticData/PrinterSettings/Lulzbot/TAZ PLA/config.ini

@@ -0,0 +1,114 @@
+avoid_crossing_perimeters = 0
+bed_size = 298,275
+bed_temperature = 65
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+build_height = 250
+complete_objects = 0
+cooling = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid =  1,1
+end_gcode =  M104 S0 ; turn off temperature\nG1 X10 Y200\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_offset =  0x0
+extrusion_axis =  E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_diameter = 3
+fill_angle = 45
+fill_density = 0.3
+fill_pattern =  rectilinear
+first_layer_bed_temperature = 65
+first_layer_extrusion_width = 200%
+first_layer_height = 0.25
+first_layer_speed = 30%
+first_layer_temperature = 185
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor =  reprap
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_gcode =  
+layer_height = 0.2
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 5
+notes =  
+nozzle_diameter = 0.35
+only_retract_when_crossing_perimeters = 0
+output_filename_format =  [input_filename_base].gcode
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process =  
+print_center =  149,137.5
+raft_layers = 0
+randomize_start = 1
+resolution = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 3
+retract_length_toolchange = 10
+retract_lift = 1
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 30
+small_perimeter_speed = 35
+solid_fill_pattern =  rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+start_gcode =  G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle
+support_material = 1
+support_material_angle = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_pattern =  rectilinear
+support_material_spacing = 3
+support_material_speed = 60
+support_material_threshold = 30
+temperature = 185
+threads = 2
+toolchange_gcode =  
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 3
+travel_speed = 150
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0

StaticData/PrinterSettings/Lulzbot/TAZ PLA/setup.ini

@@ -0,0 +1 @@
+baud_rate = 250000

StaticData/PrinterSettings/Portabee/Portabee GO ABS/config.ini

@@ -0,0 +1,114 @@
+avoid_crossing_perimeters = 0
+bed_size = 120,168
+bed_temperature = 100
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+build_height = 135
+complete_objects = 0
+cooling = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid =  1,1
+end_gcode =  M104 S0 ; turn off temperature\nG1 X10 Y200\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_offset =  0x0
+extrusion_axis =  E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 45
+fill_density = 0.3
+fill_pattern =  rectilinear
+first_layer_bed_temperature = 100
+first_layer_extrusion_width = 200%
+first_layer_height = 0.25
+first_layer_speed = 30%
+first_layer_temperature = 230
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor =  reprap
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_gcode =  
+layer_height = 0.2
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 5
+notes =  
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 0
+output_filename_format =  [input_filename_base].gcode
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process =  
+print_center =  60,84
+raft_layers = 0
+randomize_start = 1
+resolution = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 3
+retract_length_toolchange = 10
+retract_lift = 1
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 30
+small_perimeter_speed = 35
+solid_fill_pattern =  rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+start_gcode =  G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle
+support_material = 1
+support_material_angle = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_pattern =  rectilinear
+support_material_spacing = 3
+support_material_speed = 60
+support_material_threshold = 30
+temperature = 230
+threads = 2
+toolchange_gcode =  
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 3
+travel_speed = 150
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0

StaticData/PrinterSettings/Portabee/Portabee GO ABS/setup.ini

@@ -0,0 +1 @@
+baud_rate = 250000

StaticData/PrinterSettings/Portabee/Portabee GO PLA/config.ini

@@ -0,0 +1,114 @@
+avoid_crossing_perimeters = 0
+bed_size = 120,168
+bed_temperature = 65
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+build_height = 135
+complete_objects = 0
+cooling = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid =  1,1
+end_gcode =  M104 S0 ; turn off temperature\nG1 X10 Y200\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_offset =  0x0
+extrusion_axis =  E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 45
+fill_density = 0.3
+fill_pattern =  rectilinear
+first_layer_bed_temperature = 65
+first_layer_extrusion_width = 200%
+first_layer_height = 0.25
+first_layer_speed = 30%
+first_layer_temperature = 190
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor =  reprap
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_gcode =  
+layer_height = 0.2
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 5
+notes =  
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 0
+output_filename_format =  [input_filename_base].gcode
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process =  
+print_center =  60,84
+raft_layers = 0
+randomize_start = 1
+resolution = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 3
+retract_length_toolchange = 10
+retract_lift = 1
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 30
+small_perimeter_speed = 35
+solid_fill_pattern =  rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+start_gcode =  G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle
+support_material = 1
+support_material_angle = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_pattern =  rectilinear
+support_material_spacing = 3
+support_material_speed = 60
+support_material_threshold = 30
+temperature = 190
+threads = 2
+toolchange_gcode =  
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 3
+travel_speed = 150
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0

StaticData/PrinterSettings/Portabee/Portabee GO PLA/setup.ini

@@ -0,0 +1 @@
+baud_rate = 250000

StaticData/PrinterSettings/SeeMeCNC/Orion ABS/config.ini

@@ -1,5 +1,4 @@
 avoid_crossing_perimeters = 1
-bed_shape = circular
 bed_size = 260,260
 bed_temperature = 70
 bottom_solid_layers = 5
@@ -8,6 +7,7 @@ bridge_fan_speed = 100
 bridge_flow_ratio = 1
 bridge_speed = 60
 brim_width = 0
+build_height = 228.6
 complete_objects = 0
 cooling = 1
 default_acceleration = 0

StaticData/PrinterSettings/SeeMeCNC/Orion PLA/config.ini

@@ -1,5 +1,4 @@
 avoid_crossing_perimeters = 1
-bed_shape = circular
 bed_size = 260,260
 bed_temperature = 70
 bottom_solid_layers = 5
@@ -8,6 +7,7 @@ bridge_fan_speed = 100
 bridge_flow_ratio = 1
 bridge_speed = 60
 brim_width = 0
+build_height = 228.6
 complete_objects = 0
 cooling = 1
 default_acceleration = 0

StaticData/PrinterSettings/SeeMeCNC/RostockMAX/config.ini

@@ -1,13 +1,13 @@
+# generated by Slic3r 0.9.9 on Tue May 14 10:04:09 2013
 avoid_crossing_perimeters = 1
 bed_size = 280,280
-bed_shape = circular
 bed_temperature = 80
 bottom_solid_layers = 3
 bridge_acceleration = 0
 bridge_fan_speed = 100
 bridge_flow_ratio = 1
 bridge_speed = 20
-brim_width = 0
+brim_width = 0build_height = 374.65
 complete_objects = 0
 cooling = 1
 default_acceleration = 0

StaticData/PrinterSettings/Solidoodle/Solidoodle 2 ABS/config.ini

@@ -0,0 +1,114 @@
+avoid_crossing_perimeters = 0
+bed_size = 152.4,152.4
+bed_temperature = 105
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+build_height = 152.4
+complete_objects = 0
+cooling = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid =  1,1
+end_gcode =  M104 S0 ; turn off temperature\nG1 X10 Y200\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_offset =  0x0
+extrusion_axis =  E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 45
+fill_density = 0.3
+fill_pattern =  rectilinear
+first_layer_bed_temperature = 105
+first_layer_extrusion_width = 200%
+first_layer_height = 0.25
+first_layer_speed = 30%
+first_layer_temperature = 215
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor =  reprap
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_gcode =  
+layer_height = 0.2
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 5
+notes =  
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 0
+output_filename_format =  [input_filename_base].gcode
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process =  
+print_center =  76.2,76.2
+raft_layers = 0
+randomize_start = 1
+resolution = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 3
+retract_length_toolchange = 10
+retract_lift = 1
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 30
+small_perimeter_speed = 35
+solid_fill_pattern =  rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+start_gcode =  G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle
+support_material = 1
+support_material_angle = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_pattern =  rectilinear
+support_material_spacing = 3
+support_material_speed = 60
+support_material_threshold = 30
+temperature = 215
+threads = 2
+toolchange_gcode =  
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 3
+travel_speed = 150
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0

StaticData/PrinterSettings/Solidoodle/Solidoodle 2 ABS/setup.ini

@@ -0,0 +1,2 @@
+baud_rate = 250000
+windows_driver = serial_install.exe

StaticData/PrinterSettings/Solidoodle/Solidoodle 2 PLA/config.ini

@@ -0,0 +1,114 @@
+avoid_crossing_perimeters = 0
+bed_size = 152.4,152.4
+bed_temperature = 65
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+build_height = 152.4
+complete_objects = 0
+cooling = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid =  1,1
+end_gcode =  M104 S0 ; turn off temperature\nG1 X10 Y200\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_offset =  0x0
+extrusion_axis =  E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 45
+fill_density = 0.3
+fill_pattern =  rectilinear
+first_layer_bed_temperature = 65
+first_layer_extrusion_width = 200%
+first_layer_height = 0.25
+first_layer_speed = 30%
+first_layer_temperature = 190
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor =  reprap
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_gcode =  
+layer_height = 0.2
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 5
+notes =  
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 0
+output_filename_format =  [input_filename_base].gcode
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process =  
+print_center =  76.2,76.2
+raft_layers = 0
+randomize_start = 1
+resolution = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 3
+retract_length_toolchange = 10
+retract_lift = 1
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 30
+small_perimeter_speed = 35
+solid_fill_pattern =  rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+start_gcode =  G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle
+support_material = 1
+support_material_angle = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_pattern =  rectilinear
+support_material_spacing = 3
+support_material_speed = 60
+support_material_threshold = 30
+temperature = 190
+threads = 2
+toolchange_gcode =  
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 3
+travel_speed = 150
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0

StaticData/PrinterSettings/Solidoodle/Solidoodle 2 PLA/setup.ini

@@ -0,0 +1,2 @@
+baud_rate = 250000
+windows_driver = serial_install.exe

StaticData/PrinterSettings/Solidoodle/Solidoodle 3 ABS/config.ini

@@ -0,0 +1,114 @@
+avoid_crossing_perimeters = 0
+bed_size = 203.2,203.2
+bed_temperature = 105
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+build_height = 203.2
+complete_objects = 0
+cooling = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid =  1,1
+end_gcode =  M104 S0 ; turn off temperature\nG1 X10 Y200\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_offset =  0x0
+extrusion_axis =  E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 45
+fill_density = 0.3
+fill_pattern =  rectilinear
+first_layer_bed_temperature = 105
+first_layer_extrusion_width = 200%
+first_layer_height = 0.25
+first_layer_speed = 30%
+first_layer_temperature = 215
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor =  reprap
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_gcode =  
+layer_height = 0.2
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 5
+notes =  
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 0
+output_filename_format =  [input_filename_base].gcode
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process =  
+print_center =  101.6,101.6
+raft_layers = 0
+randomize_start = 1
+resolution = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 3
+retract_length_toolchange = 10
+retract_lift = 1
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 30
+small_perimeter_speed = 35
+solid_fill_pattern =  rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+start_gcode =  G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle
+support_material = 1
+support_material_angle = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_pattern =  rectilinear
+support_material_spacing = 3
+support_material_speed = 60
+support_material_threshold = 30
+temperature = 215
+threads = 2
+toolchange_gcode =  
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 3
+travel_speed = 150
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0

StaticData/PrinterSettings/Solidoodle/Solidoodle 3 ABS/setup.ini

@@ -0,0 +1,2 @@
+baud_rate = 250000
+windows_driver = serial_install.exe

StaticData/PrinterSettings/Solidoodle/Solidoodle 3 PLA/config.ini

@@ -0,0 +1,114 @@
+avoid_crossing_perimeters = 0
+bed_size = 203.2,203.2
+bed_temperature = 65
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+build_height = 203.2
+complete_objects = 0
+cooling = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid =  1,1
+end_gcode =  M104 S0 ; turn off temperature\nG1 X10 Y200\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_offset =  0x0
+extrusion_axis =  E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 45
+fill_density = 0.3
+fill_pattern =  rectilinear
+first_layer_bed_temperature = 65
+first_layer_extrusion_width = 200%
+first_layer_height = 0.25
+first_layer_speed = 30%
+first_layer_temperature = 190
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor =  reprap
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_gcode =  
+layer_height = 0.2
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 5
+notes =  
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 0
+output_filename_format =  [input_filename_base].gcode
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process =  
+print_center =  101.6,101.6
+raft_layers = 0
+randomize_start = 1
+resolution = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 3
+retract_length_toolchange = 10
+retract_lift = 1
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 30
+small_perimeter_speed = 35
+solid_fill_pattern =  rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+start_gcode =  G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle
+support_material = 1
+support_material_angle = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_pattern =  rectilinear
+support_material_spacing = 3
+support_material_speed = 60
+support_material_threshold = 30
+temperature = 190
+threads = 2
+toolchange_gcode =  
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 3
+travel_speed = 150
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0

StaticData/PrinterSettings/Solidoodle/Solidoodle 3 PLA/setup.ini

@@ -0,0 +1,2 @@
+baud_rate = 250000
+windows_driver = serial_install.exe

StaticData/PrinterSettings/Solidoodle/Solidoodle 4 ABS/config.ini

@@ -0,0 +1,114 @@
+avoid_crossing_perimeters = 0
+bed_size = 203.2,203.2
+bed_temperature = 105
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+build_height = 203.2
+complete_objects = 0
+cooling = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid =  1,1
+end_gcode =  M104 S0 ; turn off temperature\nG1 X10 Y200\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_offset =  0x0
+extrusion_axis =  E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 45
+fill_density = 0.3
+fill_pattern =  rectilinear
+first_layer_bed_temperature = 105
+first_layer_extrusion_width = 200%
+first_layer_height = 0.25
+first_layer_speed = 30%
+first_layer_temperature = 215
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor =  reprap
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_gcode =  
+layer_height = 0.2
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 5
+notes =  
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 0
+output_filename_format =  [input_filename_base].gcode
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process =  
+print_center =  101.6,101.6
+raft_layers = 0
+randomize_start = 1
+resolution = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 3
+retract_length_toolchange = 10
+retract_lift = 1
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 30
+small_perimeter_speed = 35
+solid_fill_pattern =  rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+start_gcode =  G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle
+support_material = 1
+support_material_angle = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_pattern =  rectilinear
+support_material_spacing = 3
+support_material_speed = 60
+support_material_threshold = 30
+temperature = 215
+threads = 2
+toolchange_gcode =  
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 3
+travel_speed = 150
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0

StaticData/PrinterSettings/Solidoodle/Solidoodle 4 ABS/setup.ini

@@ -0,0 +1,2 @@
+baud_rate = 250000
+windows_driver = serial_install.exe

StaticData/PrinterSettings/Solidoodle/Solidoodle 4 PLA/config.ini

@@ -0,0 +1,114 @@
+avoid_crossing_perimeters = 0
+bed_size = 203.2,203.2
+bed_temperature = 65
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+build_height = 203.2
+complete_objects = 0
+cooling = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid =  1,1
+end_gcode =  M104 S0 ; turn off temperature\nG1 X10 Y200\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_offset =  0x0
+extrusion_axis =  E
+extrusion_multiplier = 1
+extrusion_width = 0
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 45
+fill_density = 0.3
+fill_pattern =  rectilinear
+first_layer_bed_temperature = 65
+first_layer_extrusion_width = 200%
+first_layer_height = 0.25
+first_layer_speed = 30%
+first_layer_temperature = 190
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor =  reprap
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_gcode =  
+layer_height = 0.2
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 5
+notes =  
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 0
+output_filename_format =  [input_filename_base].gcode
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process =  
+print_center =  101.6,101.6
+raft_layers = 0
+randomize_start = 1
+resolution = 0
+retract_before_travel = 2
+retract_layer_change = 1
+retract_length = 3
+retract_length_toolchange = 10
+retract_lift = 1
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 30
+small_perimeter_speed = 35
+solid_fill_pattern =  rectilinear
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
+spiral_vase = 0
+start_gcode =  G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle
+support_material = 1
+support_material_angle = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_pattern =  rectilinear
+support_material_spacing = 3
+support_material_speed = 60
+support_material_threshold = 30
+temperature = 190
+threads = 2
+toolchange_gcode =  
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 50
+top_solid_layers = 3
+travel_speed = 150
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 0
+z_offset = 0

StaticData/PrinterSettings/Solidoodle/Solidoodle 4 PLA/setup.ini

@@ -0,0 +1,2 @@
+baud_rate = 250000
+windows_driver = serial_install.exe

StaticData/PrinterSettings/Type A Machines/Series 1/config.ini

@@ -5,6 +5,7 @@ bridge_fan_speed = 100
 bridge_flow_ratio = 0.6
 bridge_speed = 60
 brim_width = 0
+build_height = 228.6
 complete_objects = 0
 cooling = 1
 disable_fan_first_layers = 1

StaticData/PrinterSettings/config.ini

@@ -1,5 +1,4 @@
 avoid_crossing_perimeters = 0
-bed_shape = rectangular
 bed_size = 200,200
 bed_temperature = 70
 bottom_solid_layers = 3
@@ -10,7 +9,6 @@ bridge_speed = 60
 brim_width = 0
 build_height = 0
 complete_objects = 0
-cool_extruder_lift = 0
 cooling = 1
 default_acceleration = 0
 disable_fan_first_layers = 1
@@ -96,7 +94,6 @@ start_perimeters_at_concave_points = 0
 start_perimeters_at_non_overhang = 0
 support_material = 0
 support_material_angle = 0
-support_material_create_internal_support = 0
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0