added material settings for PrintSpace Altair

StaticData/PrinterSettings/PrintSpace/Altair/material/ABS.slice

@@ -0,0 +1,152 @@
+avoid_crossing_perimeters = 1
+bed_shape = circular
+bed_size = 210,210
+bed_temperature = 100
+bottom_clip_amount = 0
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 25
+bridge_flow_ratio = 1
+bridge_speed = 30
+brim_width = 0
+build_height = 255
+cancel_gcode = G28\n
+center_part_on_bed = 1
+complete_objects = 0
+cool_extruder_lift = 0
+cooling = 1
+create_raft = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+end_gcode = M104 S0 ; turn off temperature\nM140 S0\nG28\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_count = 1
+extruder_offset = 0x0
+extruders_share_temperature = 0
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width = 0.6
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.76
+fill_angle = 0
+fill_density = 1
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_bed_temperature = 90
+first_layer_extrusion_width = 0.6
+first_layer_height = 0.35
+first_layer_speed = 10
+first_layer_temperature = 230
+g0 = 0
+gap_fill_speed = 30
+gcode_arcs = 1
+gcode_comments = 0
+gcode_flavor = reprap
+gcode_output_type = REPRAP
+has_fan = 1
+has_hardware_leveling = 0
+has_heated_bed = 1
+has_sd_card_reader = 1
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0.6
+infill_first = 
+infill_only_where_needed = 0
+infill_overlap_perimeter = .06
+infill_speed = 50
+infill_type = GRID
+layer_gcode = 
+layer_height = 0.25
+max_fan_speed = 0
+min_extrusion_before_retract = 0.5
+min_fan_speed = 0
+min_print_speed = 10
+min_skirt_length = 4
+notes = 
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+pause_gcode = G91\nG1 Z10 E-10 F12000\nG90
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0.6
+perimeter_speed = 50
+perimeters = 3
+post_process = 
+print_center = 0,0
+raft_air_gap = .2
+raft_extruder = 0
+raft_extra_distance_around_part = 5
+raft_fan_speed_percent = 100
+raft_layers = 0
+raft_print_speed = 100%
+randomize_start = 
+repair_outlines_extensive_stitching = 1
+repair_outlines_keep_open = 1
+resolution = 0
+resume_gcode = G91\nG1 Z-10 E10.5 F12000\nG90
+retract_before_travel = 6
+retract_layer_change = 0
+retract_length = 3
+retract_length_tool_change = 6
+retract_lift = 0.6
+retract_restart_extra = 0.1
+retract_restart_extra_toolchange = 0
+retract_speed = 100
+skirt_distance = 3
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 8
+small_perimeter_speed = 30
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 20
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0.6
+solid_infill_speed = 30
+spiral_vase = 0
+standby_temperature_delta = -5
+start_gcode = G28 ; home all axes
+start_perimeters_at_concave_points = 0
+start_perimeters_at_non_overhang = 0
+support_material = 0
+support_material_angle = 0
+support_material_create_internal_support = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_infill_angle = 45
+support_material_interface_extruder = 1
+support_material_interface_layers = 2
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 20
+support_material_threshold = 15
+support_material_xy_distance = 0.7
+support_material_z_distance = 0.15
+support_material_z_gap_layers = 1
+support_type = GRID
+temperature = 245
+thin_walls = 1
+threads = 4
+toolchange_gcode = 
+top_infill_extrusion_width = 0.6
+top_solid_infill_speed = 30
+top_solid_layers = 4
+travel_speed = 50
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 1
+wipe_shield_distance = 0
+wipe_tower_size = 0
+z_can_be_negative = 1
+z_offset = 0

StaticData/PrinterSettings/PrintSpace/Altair/material/Bridge.slice

@@ -0,0 +1,152 @@
+avoid_crossing_perimeters = 1
+bed_shape = circular
+bed_size = 210,210
+bed_temperature = 0
+bottom_clip_amount = 0
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 30
+brim_width = 0
+build_height = 255
+cancel_gcode = G28\n
+center_part_on_bed = 1
+complete_objects = 0
+cool_extruder_lift = 0
+cooling = 1
+create_raft = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+end_gcode = M104 S0 ; turn off temperature\nM140 S0\nG28\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_count = 1
+extruder_offset = 0x0
+extruders_share_temperature = 0
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width = 0.6
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.76
+fill_angle = 0
+fill_density = 1
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_bed_temperature = 90
+first_layer_extrusion_width = 0.6
+first_layer_height = 0.35
+first_layer_speed = 10
+first_layer_temperature = 230
+g0 = 0
+gap_fill_speed = 30
+gcode_arcs = 1
+gcode_comments = 0
+gcode_flavor = reprap
+gcode_output_type = REPRAP
+has_fan = 1
+has_hardware_leveling = 0
+has_heated_bed = 1
+has_sd_card_reader = 1
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0.6
+infill_first = 
+infill_only_where_needed = 0
+infill_overlap_perimeter = .06
+infill_speed = 50
+infill_type = GRID
+layer_gcode = 
+layer_height = 0.25
+max_fan_speed = 0
+min_extrusion_before_retract = 0.5
+min_fan_speed = 0
+min_print_speed = 10
+min_skirt_length = 4
+notes = 
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+pause_gcode = G91\nG1 Z10 E-10 F12000\nG90
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0.6
+perimeter_speed = 50
+perimeters = 3
+post_process = 
+print_center = 0,0
+raft_air_gap = .2
+raft_extruder = 0
+raft_extra_distance_around_part = 5
+raft_fan_speed_percent = 100
+raft_layers = 0
+raft_print_speed = 100%
+randomize_start = 
+repair_outlines_extensive_stitching = 1
+repair_outlines_keep_open = 1
+resolution = 0
+resume_gcode = G91\nG1 Z-10 E10.5 F12000\nG90
+retract_before_travel = 6
+retract_layer_change = 0
+retract_length = 3
+retract_length_tool_change = 6
+retract_lift = 0.6
+retract_restart_extra = 0.1
+retract_restart_extra_toolchange = 0
+retract_speed = 100
+skirt_distance = 3
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 8
+small_perimeter_speed = 30
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 20
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0.6
+solid_infill_speed = 30
+spiral_vase = 0
+standby_temperature_delta = -5
+start_gcode = G28 ; home all axes
+start_perimeters_at_concave_points = 0
+start_perimeters_at_non_overhang = 0
+support_material = 0
+support_material_angle = 0
+support_material_create_internal_support = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_infill_angle = 45
+support_material_interface_extruder = 1
+support_material_interface_layers = 2
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 20
+support_material_threshold = 15
+support_material_xy_distance = 0.7
+support_material_z_distance = 0.15
+support_material_z_gap_layers = 1
+support_type = GRID
+temperature = 260
+thin_walls = 1
+threads = 4
+toolchange_gcode = 
+top_infill_extrusion_width = 0.6
+top_solid_infill_speed = 30
+top_solid_layers = 4
+travel_speed = 50
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 1
+wipe_shield_distance = 0
+wipe_tower_size = 0
+z_can_be_negative = 1
+z_offset = 0

StaticData/PrinterSettings/PrintSpace/Altair/material/Poly-Flex PLA.slice

@@ -0,0 +1,152 @@
+avoid_crossing_perimeters = 1
+bed_shape = circular
+bed_size = 210,210
+bed_temperature = 60
+bottom_clip_amount = 0
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 30
+brim_width = 0
+build_height = 255
+cancel_gcode = G28\n
+center_part_on_bed = 1
+complete_objects = 0
+cool_extruder_lift = 0
+cooling = 1
+create_raft = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+end_gcode = M104 S0 ; turn off temperature\nM140 S0\nG28\nM84     ; disable motors
+external_perimeter_speed = 25
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_count = 1
+extruder_offset = 0x0
+extruders_share_temperature = 0
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width = 0.6
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.76
+fill_angle = 0
+fill_density = 1
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_bed_temperature = 90
+first_layer_extrusion_width = 0.6
+first_layer_height = 0.35
+first_layer_speed = 10
+first_layer_temperature = 230
+g0 = 0
+gap_fill_speed = 30
+gcode_arcs = 1
+gcode_comments = 0
+gcode_flavor = reprap
+gcode_output_type = REPRAP
+has_fan = 1
+has_hardware_leveling = 0
+has_heated_bed = 1
+has_sd_card_reader = 1
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0.6
+infill_first = 
+infill_only_where_needed = 0
+infill_overlap_perimeter = .06
+infill_speed = 25
+infill_type = GRID
+layer_gcode = 
+layer_height = 0.25
+max_fan_speed = 100
+min_extrusion_before_retract = 0.5
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 4
+notes = 
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+pause_gcode = G91\nG1 Z10 E-10 F12000\nG90
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0.6
+perimeter_speed = 25
+perimeters = 3
+post_process = 
+print_center = 0,0
+raft_air_gap = .2
+raft_extruder = 0
+raft_extra_distance_around_part = 5
+raft_fan_speed_percent = 100
+raft_layers = 0
+raft_print_speed = 100%
+randomize_start = 
+repair_outlines_extensive_stitching = 1
+repair_outlines_keep_open = 1
+resolution = 0
+resume_gcode = G91\nG1 Z-10 E10.5 F12000\nG90
+retract_before_travel = 6
+retract_layer_change = 0
+retract_length = 3
+retract_length_tool_change = 6
+retract_lift = 0.6
+retract_restart_extra = 0.1
+retract_restart_extra_toolchange = 0
+retract_speed = 100
+skirt_distance = 3
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 8
+small_perimeter_speed = 30
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 20
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0.6
+solid_infill_speed = 30
+spiral_vase = 0
+standby_temperature_delta = -5
+start_gcode = G28 ; home all axes
+start_perimeters_at_concave_points = 0
+start_perimeters_at_non_overhang = 0
+support_material = 0
+support_material_angle = 0
+support_material_create_internal_support = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_infill_angle = 45
+support_material_interface_extruder = 1
+support_material_interface_layers = 2
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 25
+support_material_threshold = 15
+support_material_xy_distance = 0.7
+support_material_z_distance = 0.15
+support_material_z_gap_layers = 1
+support_type = GRID
+temperature = 240
+thin_walls = 1
+threads = 4
+toolchange_gcode = 
+top_infill_extrusion_width = 0.6
+top_solid_infill_speed = 30
+top_solid_layers = 4
+travel_speed = 50
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 1
+wipe_shield_distance = 0
+wipe_tower_size = 0
+z_can_be_negative = 1
+z_offset = 0

StaticData/PrinterSettings/PrintSpace/Altair/material/Premium PLA.slice

@@ -0,0 +1,152 @@
+avoid_crossing_perimeters = 1
+bed_shape = circular
+bed_size = 210,210
+bed_temperature = 50
+bottom_clip_amount = 0
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 30
+brim_width = 0
+build_height = 255
+cancel_gcode = G28\n
+center_part_on_bed = 1
+complete_objects = 0
+cool_extruder_lift = 0
+cooling = 1
+create_raft = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+end_gcode = M104 S0 ; turn off temperature\nM140 S0\nG28\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_count = 1
+extruder_offset = 0x0
+extruders_share_temperature = 0
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width = 0.6
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.76
+fill_angle = 0
+fill_density = 1
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_bed_temperature = 90
+first_layer_extrusion_width = 0.6
+first_layer_height = 0.35
+first_layer_speed = 10
+first_layer_temperature = 230
+g0 = 0
+gap_fill_speed = 30
+gcode_arcs = 1
+gcode_comments = 0
+gcode_flavor = reprap
+gcode_output_type = REPRAP
+has_fan = 1
+has_hardware_leveling = 0
+has_heated_bed = 1
+has_sd_card_reader = 1
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0.6
+infill_first = 
+infill_only_where_needed = 0
+infill_overlap_perimeter = .06
+infill_speed = 50
+infill_type = GRID
+layer_gcode = 
+layer_height = 0.25
+max_fan_speed = 100
+min_extrusion_before_retract = 0.5
+min_fan_speed = 100
+min_print_speed = 10
+min_skirt_length = 4
+notes = 
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+pause_gcode = G91\nG1 Z10 E-10 F12000\nG90
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0.6
+perimeter_speed = 50
+perimeters = 3
+post_process = 
+print_center = 0,0
+raft_air_gap = .2
+raft_extruder = 0
+raft_extra_distance_around_part = 5
+raft_fan_speed_percent = 100
+raft_layers = 0
+raft_print_speed = 100%
+randomize_start = 
+repair_outlines_extensive_stitching = 1
+repair_outlines_keep_open = 1
+resolution = 0
+resume_gcode = G91\nG1 Z-10 E10.5 F12000\nG90
+retract_before_travel = 6
+retract_layer_change = 0
+retract_length = 3
+retract_length_tool_change = 6
+retract_lift = 0.6
+retract_restart_extra = 0.1
+retract_restart_extra_toolchange = 0
+retract_speed = 100
+skirt_distance = 3
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 8
+small_perimeter_speed = 30
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 20
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0.6
+solid_infill_speed = 30
+spiral_vase = 0
+standby_temperature_delta = -5
+start_gcode = G28 ; home all axes
+start_perimeters_at_concave_points = 0
+start_perimeters_at_non_overhang = 0
+support_material = 0
+support_material_angle = 0
+support_material_create_internal_support = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_infill_angle = 45
+support_material_interface_extruder = 1
+support_material_interface_layers = 2
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 20
+support_material_threshold = 15
+support_material_xy_distance = 0.7
+support_material_z_distance = 0.15
+support_material_z_gap_layers = 1
+support_type = GRID
+temperature = 225
+thin_walls = 1
+threads = 4
+toolchange_gcode = 
+top_infill_extrusion_width = 0.6
+top_solid_infill_speed = 30
+top_solid_layers = 4
+travel_speed = 50
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 1
+wipe_shield_distance = 0
+wipe_tower_size = 0
+z_can_be_negative = 1
+z_offset = 0

StaticData/PrinterSettings/PrintSpace/Altair/material/T-Glase.slice

@@ -0,0 +1,152 @@
+avoid_crossing_perimeters = 1
+bed_shape = circular
+bed_size = 210,210
+bed_temperature = 60
+bottom_clip_amount = 0
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_fan_speed = 25
+bridge_flow_ratio = 1
+bridge_speed = 30
+brim_width = 0
+build_height = 255
+cancel_gcode = G28\n
+center_part_on_bed = 1
+complete_objects = 0
+cool_extruder_lift = 0
+cooling = 1
+create_raft = 0
+default_acceleration = 0
+disable_fan_first_layers = 2
+end_gcode = M104 S0 ; turn off temperature\nM140 S0\nG28\nM84     ; disable motors
+external_perimeter_speed = 50
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_count = 1
+extruder_offset = 0x0
+extruders_share_temperature = 0
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width = 0.6
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.55
+fill_angle = 0
+fill_density = 1
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_bed_temperature = 90
+first_layer_extrusion_width = 0.6
+first_layer_height = 0.35
+first_layer_speed = 10
+first_layer_temperature = 230
+g0 = 0
+gap_fill_speed = 30
+gcode_arcs = 1
+gcode_comments = 0
+gcode_flavor = reprap
+gcode_output_type = REPRAP
+has_fan = 1
+has_hardware_leveling = 0
+has_heated_bed = 1
+has_sd_card_reader = 1
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0.6
+infill_first = 
+infill_only_where_needed = 0
+infill_overlap_perimeter = .06
+infill_speed = 50
+infill_type = GRID
+layer_gcode = 
+layer_height = 0.25
+max_fan_speed = 0
+min_extrusion_before_retract = 0.5
+min_fan_speed = 0
+min_print_speed = 10
+min_skirt_length = 4
+notes = 
+nozzle_diameter = 0.4
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+pause_gcode = G91\nG1 Z10 E-10 F12000\nG90
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0.6
+perimeter_speed = 50
+perimeters = 3
+post_process = 
+print_center = 0,0
+raft_air_gap = .2
+raft_extruder = 0
+raft_extra_distance_around_part = 5
+raft_fan_speed_percent = 100
+raft_layers = 0
+raft_print_speed = 100%
+randomize_start = 
+repair_outlines_extensive_stitching = 1
+repair_outlines_keep_open = 1
+resolution = 0
+resume_gcode = G91\nG1 Z-10 E10.5 F12000\nG90
+retract_before_travel = 6
+retract_layer_change = 0
+retract_length = 3
+retract_length_tool_change = 6
+retract_lift = 0.6
+retract_restart_extra = 0.1
+retract_restart_extra_toolchange = 0
+retract_speed = 100
+skirt_distance = 3
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 8
+small_perimeter_speed = 30
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 20
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0.6
+solid_infill_speed = 30
+spiral_vase = 0
+standby_temperature_delta = -5
+start_gcode = G28 ; home all axes
+start_perimeters_at_concave_points = 0
+start_perimeters_at_non_overhang = 0
+support_material = 0
+support_material_angle = 0
+support_material_create_internal_support = 0
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_infill_angle = 45
+support_material_interface_extruder = 1
+support_material_interface_layers = 2
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 20
+support_material_threshold = 15
+support_material_xy_distance = 0.7
+support_material_z_distance = 0.15
+support_material_z_gap_layers = 1
+support_type = GRID
+temperature = 245
+thin_walls = 1
+threads = 4
+toolchange_gcode = 
+top_infill_extrusion_width = 0.6
+top_solid_infill_speed = 30
+top_solid_layers = 4
+travel_speed = 50
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+vibration_limit = 0
+wipe = 1
+wipe_shield_distance = 0
+wipe_tower_size = 0
+z_can_be_negative = 1
+z_offset = 0