"cancel_gcode": "G91; Set to Relative position\\nG1 Z3 E-3; move z axis up\\nG28; home axis\\nG1 F250 E-16; Retract filament from barrel\\nG90; Set to Absolute position\\nM104 S0; turn off temperature\\nM140 S0; turn off heated bed\\nM106 S0; Turn off fan\\nM18;\\nM117 Print cancelled",
"center_part_on_bed": "1",
"complete_objects": "0",
"connect_gcode": "",
"cool_extruder_lift": "0",
"cooling": "1",
"create_raft": "0",
"default_acceleration": "0",
"disable_fan_first_layers": "1",
"end_gcode": "G91; Set to Relative position\\nG1 Z3 E-3; move z axis up\\nG28 ; home axis\\nG1 F250 E-16; Retract filament from barrel\\nG90; Set to Absolute position\\nM104 S0 ; turn off temperature\\nM140 S0 ; turn off heated bed\\nM106 S0 ; Turn off fan\\nM18;\\nM117 All Done!!!",
"pause_gcode": "G91;\\nG1 F250 Z10 X10 E-16; Retract filament from barrel\\nG90;\\nM104 S0; set to holding temp\\nM117 Print paused",
"perimeter_acceleration": "0",
"perimeter_extruder": "1",
"perimeter_extrusion_width": "0",
"perimeter_speed": "80",
"perimeters": "2",
"post_process": "",
"print_center": "100,110",
"print_leveling_method": "Manual",
"print_leveling_required_to_print": "0",
"print_leveling_solution": "3 Point Plane",
"raft_air_gap": ".2",
"raft_extra_distance_around_part": "5",
"raft_extruder": "0",
"raft_fan_speed_percent": "100",
"raft_layers": "0",
"raft_print_speed": "100%",
"randomize_start": "0",
"repair_outlines_extensive_stitching": "1",
"repair_outlines_keep_open": "1",
"resolution": "0",
"resume_gcode": "M117 Print resumed\\nM109 S[temperature]; Set print temperature \\nG91;\\nG1 F250 Z-10 X-10 E16; Prime filament from barrel\\nG90;",
"retract_before_travel": "0.8",
"retract_layer_change": "0",
"retract_length": "2.5",
"retract_length_tool_change": "10",
"retract_lift": "1",
"retract_restart_extra": "0",
"retract_restart_extra_toolchange": "0",
"retract_speed": "50",
"retract_when_changing_islands": "1",
"show_reset_connection": "0",
"skirt_distance": "3",
"skirt_height": "1",
"skirts": "1",
"slowdown_below_layer_time": "8",
"small_perimeter_speed": "30",
"solid_fill_pattern": "rectilinear",
"solid_infill_below_area": "5",
"solid_infill_every_layers": "0",
"solid_infill_extrusion_width": "0",
"solid_infill_speed": "60",
"solid_shell": "0",
"spiral_vase": "0",
"standby_temperature_delta": "-5",
"start_gcode": ";Me3D - MC1.5 startup sequence - Me2 (G5,G6,G7) Build 02/16\\n;Remove the \";\" to activate any line\\n;MAKE SURE YOU KNOW WHAT EACH LINE DOES BEFORE YOU CHANGE IT!!! The Me2 is 100% hackable and so has limited physical protection from errors in the g-code\\nM104 S[temperature] ; Start heater and continue g-code\\nG21 ; set units to millimeters\\nM201 X5000 Y5000; max accel print\\nM202 X5000 Y5000; max accel travel\\nM205 X15; max xyjerk mm/s\\nG92; Zero current head position\\nG91; Relative position\\nG1 Z10; clear bed \\nG90 ; ABS position\\nG28; home axes\\nG29; perform auto levelling at three corners\\nM82 ; use absolute distances for extrusion\\nG1 Z15 F4000; Raise Z axis clear\\nG1 X-5 F4000; Move to X axis zero\\nG1 Y5 F4000;\\nG92 E0; zero the extruded length\\nM109 S[temperature]; Set print temperature and wait\\nG1 F100 E19; extrude feed stock to prime hotend barrel and purge\\n; Create purge line\\nG1 Z[z_offset] F1000; z_offset variable only available in MC1.2.3 and above\\nG91; Relative motion \\nG1 Z0.3;\\nG1 X10 Y1 F1000; Change this value to move the position of the line on the bed\\nG1 X120 E20;\\nG1 Y1;\\nG1 X-100 E16.5;\\nG1 X-20 E2;\\nG1 X10 Y-3 F500;\\nG1 Y5 F4000;\\nG92 E0;\\nG90;\\nG92 E0; zero the extruded length again\\nM117 OK...let's print;",
"cancel_gcode": "G91; Set to Relative position\\nG1 Z3 E-3; move z axis up\\nG28; home axis\\nG92 E0; zero the extruded length\\nG1 F250 E-16; Retract filament from barrel\\nG92 E0; zero the extruded length again\\nG90; Set to Absolute position\\nM104 S0; turn off temperature\\nM140 S0; turn off heated bed\\nM106 S0; Turn off fan\\nM18;\\nM117 Print cancelled; Put message on LCD screen\\nM302 S170; Reset cold extrusion temperature",
"end_gcode": "G91; Set to Relative position\\nG1 Z3 E-3; move z axis up\\nG28 ; home axis\\nG92 E0; zero the extruded length\\nG1 F250 E-16; Retract filament from barrel\\nG92 E0; zero the extruded length again\\nG90; Set to Absolute position\\nM104 S0 ; turn off temperature\\nM140 S0 ; turn off heated bed\\nM106 S0 ; Turn off fan\\nM18;\\nM117 All Done!!! ; Put message on LCD screen\\nM302 S170; Reset cold extrusion temperature",
"first_layer_bed_temperature": "0",
"first_layer_temperature": "85",
"start_gcode": ";Me3D - MC1.3 startup sequence - Me2 (G5,G6,G7) Build 06/24/15\\n;Remove the \";\" to activate any line\\n;MAKE SURE YOU KNOW WHAT EACH LINE DOES BEFORE YOU CHANGE IT!!! The Me2 is 100% hackable and so has limited physical protection from errors in the g-code\\nM104 S[temperature] ; // Start heater and continue g-code\\nG21 ; // set units to millimeters\\nM201 X3000 Y3000; // max accel print\\nM202 X3000 Y3000; // max accel travel\\nM205 X10; // max xyjerk mm/s\\nG91; // Relative position\\nG1 Z10; // clear bed \\nG90 ; // ABS position\\nG28; // home axes\\nG29; // perform auto levelling at three corners\\nM82 ; // use absolute distances for extrusion\\nG1 Z15 F4000; // Raise Z axis clear\\nG1 X-5 F4000; // Move to X axis zero\\nG1 Y5 F4000;\\nG92 E0; // zero the extruded length\\nM109 S[temperature]; // Set print temperature and wait\\nM302 S75; // Set cold extrusion level\\nG1 F100 E19; // extrude feed stock to prime hotend barrel and purge\\n; //Create purge line\\nG1 Z[z_offset] F1000; // z_offset variable only available in 1.2.3 and above\\nG91; // Relative motion \\nG1 Z0.3;\\nG1 X10 Y1 F1000; // Change this value to move the position of the line on the bed\\nG1 X120 E20;\\nG1 Y1;\\nG1 X-100 E16.5;\\nG1 X-20 E2;\\nG1 X10 Y-3 F500;\\nG1 Y5 F4000;\\nG92 E0;\\nG90;\\nG92 E0; // zero the extruded length again\\nM117 OK...let's print; // Put message on LCD screen",
