"insert_filament_markdown": "# 1. Insert filament into the extruder until you feel it start to feed\\n\\n* Make sure the filament is all the way into the extruder.\\n* Hold the filament for several seconds until it catches.\\n* Test that it is inserted by gently pulling down, there should be some resistance.\\n \\n# 2. Click 'Continue'\\n\\n",
"trim_filament_markdown": "# Trim the end of the filament\\n\\nUse wire cutters to trim the end of the filament\\nat an angle.\\n\\n\\n\\nA pointed end ensures that the filament will\\nslide easily into the extruder. If the filament\\nhas a square end, it may get caught on ridges\\ninside the extruder, preventing it from going\\nin all the way.\\n"
"trim_filament_markdown": "Trim the end of the filament to ensure a good load. \n \nMake sure you trim it at a slight angle",
"insert_filament_markdown": "* Insert filament into the extruder until you feel it start to feed\n * Make sure the filament is all the way into the extruder\n * Hold the filament for several seconds until it catches\n * Test that it is inserted by gently pulling down, there should be some resistance \n* Click 'Continue' \n",
"running_clean_markdown": "In a few seconds filament should be coming out of the extruder\n* Wait for the new filament to be coming out with no trace of the previous filament\n* Click 'Continue' when the new filament is running cleanly\n## Success! Your new filament should now be loaded",
"bottom_solid_layers": "1mm",
"layer_to_pause": "",
"bridge_speed": "20",
"air_gap_speed": "15",
"bottom_infill_speed": "0",
"build_height": "0",
"cancel_gcode": "",
"complete_objects": "0",
"connect_gcode": "",
"cool_extruder_lift": "0",
"cooling": "1",
"create_raft": "0",
"raft_extra_distance_around_part": "5",
"raft_air_gap": ".2",
"raft_print_speed": "100%",
"end_gcode": "M104 S0 ; turn off temperature\\nG28 X0 ; home X axis\\nM84 ; disable motors",
"external_perimeter_speed": "70%",
"external_perimeters_first": "0",
"extruder_count": "1",
"extruder_offset": "0x0,0x0,0x0,0x0",
"baby_step_z_offset": "0",
"extruders_share_temperature": "0",
"heat_extruder_before_homing": "0",
"merge_overlapping_lines": "1",
"expand_thin_walls": "1",
"extrusion_multiplier": "1",
"filament_cost": "0",
"filament_density": "1.24",
"filament_diameter": "3",
"fill_angle": "45",
"fill_density": "0.4",
"fill_pattern": "honeycomb",
"fill_thin_gaps": "1",
"first_layer_bed_temperature": "75",
"first_layer_extrusion_width": "100%",
"first_layer_height": "0.3",
"first_layer_speed": "30%",
"number_of_first_layers": "1",
"recover_first_layer_speed": "10",
"recover_is_enabled": "0",
"validate_layer_height": "1",
"z_homes_to_max": "0",
"recover_position_before_z_home": "0,0",
"first_layer_temperature": "205",
"auto_release_motors": "1",
"g0": "0",
"gcode_flavor": "reprap",
"gcode_output_type": "REPRAP",
"has_z_probe": "0",
"has_z_servo": "0",
"has_hardware_leveling": "0",
"has_heated_bed": "1",
"sla_printer": "0",
"include_firmware_updater": "None",
"backup_firmware_before_update": "1",
"has_power_control": "0",
"has_sd_card_reader": "0",
"show_reset_connection": "0",
"infill_overlap_perimeter": "25%",
"laser_speed_025": "100",
"laser_speed_100": "85",
"infill_speed": "60",
"infill_type": "TRIANGLES",
"print_leveling_solution": "3 Point Plane",
"leveling_sample_points": "20,20,100,180,180,20",
"probe_offset_sample_point": "100,100",
"print_leveling_required_to_print": "0",
"filament_runout_sensor": "0",
"probe_has_been_calibrated": "0",
"print_leveling_probe_start": "10",
"z_probe_z_offset": ".1",
"use_z_probe": "0",
"z_probe_xy_offset": "0,0",
"z_probe_samples": "1",
"z_servo_depolyed_angle": "0",
"z_servo_retracted_angle": "0",
"layer_gcode": "; LAYER:[layer_num]",
"layer_height": "0.4",
"solid_shell": "0",
"min_extrusion_before_retract": ".1",
"has_fan": "1",
"enable_fan": "1",
"min_fan_speed_layer_time": "60",
"max_fan_speed_layer_time": "30",
"min_fan_speed": "35",
"max_fan_speed": "100",
"bridge_fan_speed": "100",
"disable_fan_first_layers": "1",
"min_print_speed": "10",
"min_skirt_length": "0",
"nozzle_diameter": "0.5",
"calibration_files": "Calibration - Box.stl",
"make": "Undefined",
"model": "Undefined",
"output_only_first_layer": "0",
"pause_gcode": "",
"perimeter_extrusion_width": "0",
"external_perimeter_extrusion_width": "100%",
"perimeter_speed": "30",
"perimeter_start_end_overlap": "90",
"perimeters": "3",
"print_center": "100,100",
"raft_layers": "0",
"randomize_start": "0",
"resume_gcode": "",
"retract_before_travel": "20",
"enable_retractions": "1",
"retract_length": "1",
"retract_length_tool_change": "10",
"retract_when_changing_islands": "1",
"retract_lift": "0",
"retract_restart_extra_toolchange": "0",
"reset_long_extrusion": "1",
"send_with_checksum": "1",
"retract_restart_extra": "0",
"retract_restart_extra_time_to_apply": "0",
"retract_speed": "30",
"repair_outlines_extensive_stitching": "0",
"repair_outlines_keep_open": "0",
"resolution": "0",
"skirt_distance": "6",
"skirt_height": "1",
"skirts": "1",
"brims": "0",
"slowdown_below_layer_time": "30",
"small_perimeter_speed": "30",
"solid_fill_pattern": "rectilinear",
"solid_infill_extrusion_width": "0",
"solid_infill_speed": "60",
"spiral_vase": "0",
"standby_temperature_delta": "-5",
"start_gcode": "G28 ; home all axes\\nG1 Z5 F5000 ; lift nozzle",
