English:This controls the ratio of material extruder during bridging. Reducing this slightly can help bridging by stretching the filament more, using a fan can also help greatly.
Translated:Ceci contrôle le ratio de matière extrudée pendant le pontage (bridging). Réduire ce paramètre légèrement peut aider en tirant plus sur le filament. L'utilisation d'un ventilateur peut grandement aider.
Translated:Accélération à utiliser sur tous les mouvements non définis ci-dessus. Utiliser 0 pour désactiver le changement d'accélération de l'imprimante.
Translated:Vitesse utilisée pour imprimer la surface extérieure visible de l'object. Ce paramètre peut être donné explicitement en mm/s ou en utilisant un pourcentage de vitesse de périphérie.
Translated:C'est le décallage de chaque tête chauffante relative à la première tête chauffante. Seulement utile pour les machines à multiple têtes chauffantes.
English:All extrusions are multiplied by this value. Increasing it above 1 (1.1 is a good max value) will increase the amount of filament being extruded; decreasing it (.9 is a good min value) will decrease the amount being extruded.
Translated:Toutes les extrusions sont multipliées par ce facteur. Augmenter le facteur au dessus de 1 (1.1 est une bonne valeur max) vont augmenter la quantité de filament extrudé; Diminuer ce facteur (0.9 est une bonne valeur min) diminuera la quantité de filament extrudé.
Translated:Ce paramètre forcera le ventilateur à rester allumer pendant toutes la durée de l'impression. En règle générale, vous devez avoir ce paramètre désactivé et activer l'auto refroidissement (auto cooling).
English:This should be set to the actual diameter of the filament you are using on your printer. Measure 5 times with calipers, throw out the top and bottom, and average the remaining 3.
Translated:Ce paramètre doit correspondre à la valeur réelle du diamètre du filament utilisé sur votre imprimante. Mesurez 5 fois avec un pied à coulisse en prenant 5 points sur une bone longeur de fil et faites en la moyenne.
English:The temperature to set the bed to before printing the first layer. The printer will wait until this temperature has been reached before printing. Set to 0 to eliminate bed temperature commands.
Translated:Ce paramètre correspond à la température du lit avant l'impression de la première couche. L'imprimante attendra que cette température soit atteinte avant de commancer l'impression. Metre à 0 pour désactiver la chauffe du lit.
Translated:Configure la hauteur de la première couche. Il est souvent préférable d'imprimer la première couche légèrement plus épaisse que les couche suivantes afin d'optimiser l'adhésion de votre pièce sur la surface d'impression.
Translated:Ce paramètre correspond à la vitesse de déplacement pendant l'impression de la première couche. Si exprimé en pourcentage, cela modifiera la valeur précédente.
English:The temperature to set the extruder to before printing the first layer of a part. The printer will wait until this temperature has been reached before printing.
Translated:Ce paramètre correspond à la temprérature de consigne à atteindre par la tête chauffante avant le début de l'impression. L'imprimante attendra que cette température de consigne soit atteinte avant de démarrer l'impression.
Translated:Vitesse utilisée pour remplir de petits trous. Conservez la basse afin d'éviter les vibrations. Utiliser 0 afin d'éviter de remplir les petits trous.
Translated:Certains firmwares utilisent différents code pour G et M. Activer ce paramètre permet d'être sûr que le gcode généré utilisera des commandes compatibles.
Translated:Hauteur de chaque couche pendant l'impression. Un nombre très bas génère plus de couches, améliora la qualité de votre object, mais pendra plus de temps à s'imprimer.
English:Sets the minimum amount of filament to use drawing the skirt loops. This will cause at least enough skirt loops to be drawn to use this amount of filament.
Translated:Ce paramètre réduira la température de votre tête chauffante pendant les phases de non impression afin de réduire l'effet de suintement (oozing).
Translated:Fonctionalité expérimentale dont le but est d'améliorer la performance des impressions dans le vide (overhangs) en utilisants les paramètres associés au ventilateur et au pontage (bridge).
English:You can include additional programs to process the gcode after slicer is finished. The complete path of the program to run should be included here.
Translated:Vous pouvez configurer des applications suplémentaires pour gérer le gcode, avec une execution postérieure au slicer.Le chemin complet de l'application doit être inclu.
Translated:Si une couche est estimée durer moins que ce paramètre, la vitesse de déplacement de l'imprimante sera réduite afin d'allonger la durée d'impression de la couche en cours.
Translated:Utilisé pour les petites périphéries (souvent des trous de vis).Ce paramètre peut être définit directement ou en utilisant un pourcentage de la vitesse d'impression de la périphérie.
English:Force the print to have only one layer and gradually increase the extruder height during the print. Only one part can be printed at a time with this feature.
Translated:Force l'impression à avoir uniquement une couche de périphérie et augmente graduellement la hauteur de couche pendant l'impression. Un seul objet peut être imprimer à la fois en utilisant cette fonctionalité.
English:This gcode will be inserted into the output right after the temperature setting. If you have the commands to set temperature in this section they will not be generated outside of this section. You can also include values from other settings such as [first_layer_temperature].
Translated:Ce gcode sera inséré juste après la configuration des températures. Si vous avez une commande pour configurer la température dans cette section, elles ne seront pas générées en dehors de cette section. Vous pouvez aussi inclure des valeurs appartenant à d'autres paramètres tels que [first_layer_temperature].
Translated:Dernier angle à partir duquel le support sera généré. Au plus grande la valeur, au plus dens le support généré. Metre à 0 pour activer le paramètre automatique.
Translated:Vitesse d'impression au niveau du remplissage supérieur (top infill).Cette valeur peut être explicitement donnée en pourcentage par rapport à la vitesse de remplissage.
Translated:D'habitude vous devriez vouloir utiliser des distances absolue pour l'extrudeur. Cochez cette option seulement si vous êtes sûr que votre imprimante à besoin de distance relative pour l'extrudeur.
English:This is to help reduce vibrations during printing. If your printer has a resonance frequency that is causing trouble you can set this to try and reduce printing at that frequency.
Translated:Ce paramètre permet de réduire les vibrations de votre machine pendant l'impression. Si votre machine possède un point de résonance qui pose soucis, vous pouvez utiliser cette valeur afin d'essayer de déplacer ce point de résonance.
English:The file you are attempting to print is a GCode file.\n\nGCode files tell your printer exactly what to do. They are not modified by SliceSettings and my not be appropriate for your specific printer configuration.\n\nOnly print from GCode files if you know they mach your current printer and configuration.\n\nAre you sure you want to print this GCode file?
Translated:The file you are attempting to print is a GCode file.\n\nGCode files tell your printer exactly what to do. They are not modified by SliceSettings and my not be appropriate for your specific printer configuration.\n\nOnly print from GCode files if you know they mach your current printer and configuration.\n\nAre you sure you want to print this GCode file?
English:Cannot find\n'{0}'.\nWould you like to remove it from the queue?
Translated:Cannot find\n'{0}'.\nWould you like to remove it from the queue?
English:Item not found
Translated:Item not found
English:Welcome to the print leveling wizard. Here is a quick overview on what we are going to do.
Translated:Welcome to the print leveling wizard. Here is a quick overview on what we are going to do.
English:'Home' the printer
Translated:'Home' the printer
English:Sample the bed at three points
Translated:Sample the bed at three points
English:Turn auto leveling on
Translated:Turn auto leveling on
English:You should be done in about 3 minutes.
Translated:You should be done in about 3 minutes.
English:Click 'Next' to continue.
Translated:Click 'Next' to continue.
English:The printer should now be 'homing'. Once it is finished homing we will move it to the first point to sample.\n\nTo complete the next few steps you will need
Translated:The printer should now be 'homing'. Once it is finished homing we will move it to the first point to sample.\n\nTo complete the next few steps you will need
English:A standard sheet of paper
Translated:A standard sheet of paper
English:We will use this paper to measure the distance between the extruder and the bed.\n\nClick 'Next' to continue.
Translated:We will use this paper to measure the distance between the extruder and the bed.\n\nClick 'Next' to continue.
English:Congratulations!\n\nAuto Print Leveling is now configured and enabled.
Translated:Congratulations!\n\nAuto Print Leveling is now configured and enabled.
English:Remove the paper
Translated:Remove the paper
English:If in the future you wish to turn Auto Print Leveling off, you can uncheck the 'Enabled' button found in 'Advanced Settings'->'Printer Controls'.\n\nClick 'Done' to close this window.
Translated:If in the future you wish to turn Auto Print Leveling off, you can uncheck the 'Enabled' button found in 'Advanced Settings'->'Printer Controls'.\n\nClick 'Done' to close this window.
English:Using the [Z] controls on this screen, we will now take a coarse measurement of the extruder height at this position.
Translated:Using the [Z] controls on this screen, we will now take a coarse measurement of the extruder height at this position.
English:Place the paper under the extruder
Translated:Place the paper under the extruder
English:Using the above contols
Translated:Using the above contols
English:Press [Z-] until there is resistance to moving the paper
Translated:Press [Z-] until there is resistance to moving the paper
English:Press [Z+] once to release the paper
Translated:Press [Z+] once to release the paper
English:Finally click 'Next' to continue.
Translated:Finally click 'Next' to continue.
English:This part of your bed is too low for the extruder to reach it. You need to raise your bed, or lower your limit, for print leveling to work.
Translated:This part of your bed is too low for the extruder to reach it. You need to raise your bed, or lower your limit, for print leveling to work.
English:Waring Moving Too Low
Translated:Waring Moving Too Low
English:Medium Precision
Translated:Medium Precision
English:We will now refine our measurement of the extruder height at this position.
Translated:We will now refine our measurement of the extruder height at this position.
English:High Precision
Translated:High Precision
English:We will now finalize our measurement of the extruder height at this position.
Translated:We will now finalize our measurement of the extruder height at this position.
English:Press [Z-] one click PAST the first hint of resistance
Translated:Press [Z-] one click PAST the first hint of resistance
English:Save Parts Sheet
Translated:Save Parts Sheet
English:MatterContol
Translated:MatterContol
English:Saving to Parts Sheet
Translated:Saving to Parts Sheet
English:Stop trying to connect to the printer
Translated:Stop trying to connect to the printer
English:No printer selected. Press 'Connect' to choose a printer
Translated:No printer selected. Press 'Connect' to choose a printer
English:About
Translated:About
English:This controls the ratio of material extruder during bridging.Reducing this slightly can help bridging by stretching the filament more, using a fan can also help greatly.
Translated:This controls the ratio of material extruder during bridging.Reducing this slightly can help bridging by stretching the filament more, using a fan can also help greatly.
English:The default temperature to set the bed to. Can sometimes be overriden on the first layer. Set to 0 to eliminate bed temperature commands.
Translated:The default temperature to set the bed to. Can sometimes be overriden on the first layer. Set to 0 to eliminate bed temperature commands.
English:The default temperature to set the extruder to. Can sometimes be overriden on the first layer.
Translated:The default temperature to set the extruder to. Can sometimes be overriden on the first layer.
English:Macro Editor
Translated:Macro Editor
English:Macro Presets
Translated:Macro Presets
English:Edit Macro
Translated:Edit Macro
English:Macro Name
Translated:Macro Name
English:Give your macro a name
Translated:Give your macro a name
English:Macro Commands
Translated:Macro Commands
English:This should be in 'Gcode'
Translated:This should be in 'Gcode'
English:3D Printer Setup
Translated:3D Printer Setup
English:Give your printer a name.
Translated:Give your printer a name.
English:Select Make
Translated:Select Make
English:Select the printer manufacturer
Translated:Select the printer manufacturer
English:Select the printer model
Translated:Select the printer model
English:Save & Continue
Translated:Save & Continue
English:MatterControl will now attempt to auto-detect printer.
Translated:MatterControl will now attempt to auto-detect printer.
English:You cannot move any lower. This position on your bed is too low for the extruder to reach. You need to raise your bed, or adjust your limits to allow the extruder to go lower.
Translated:You cannot move any lower. This position on your bed is too low for the extruder to reach. You need to raise your bed, or adjust your limits to allow the extruder to go lower.
English:Edit Preset
Translated:Edit Preset
English:Slice-Engine
Translated:Slice-Engine
English:Status: Completed
Translated:Status: Completed
English:Unlock
Translated:Unlock
English:Show Terminal
Translated:Show Terminal
English:Configure
Translated:Configure
English:Disable
Translated:Disable
English:Est. Weight
Translated:Est. Weight
English:Downloading updates...
Translated:Downloading updates...
English:Duplicate
Translated:Duplicate
English:End
Translated:End
English:The type of support to create inside of parts.
Translated:The type of support to create inside of parts.
English:The 'Serial Port' identifies which connected device is\nyour printer. Changing which usb plug you use may\nchange the associated serial port.\n\nTip: If you are uncertain, plug-in in your printer and hit\nrefresh. The new port that appears should be your\nprinter.
Translated:The 'Serial Port' identifies which connected device is\nyour printer. Changing which usb plug you use may\nchange the associated serial port.\n\nTip: If you are uncertain, plug-in in your printer and hit\nrefresh. The new port that appears should be your\nprinter.
Translated:Make Settings Active\nAnd Save To Default
English:Design Add-ons
Translated:Design Add-ons
English:Lock Ratio
Translated:Lock Ratio
English:Retrieving download info...
Translated:Retrieving download info...
English:G-Code Output
Translated:G-Code Output
English:The extra distance the raft will extend around the part.
Translated:The extra distance the raft will extend around the part.
English:The percent of the 'Nozzle Diameter' that is the gap between the raft and the first layer. A smaller percent will make the part stick more. A larger percent will make it stick less.
Translated:The percent of the 'Nozzle Diameter' that is the gap between the raft and the first layer. A smaller percent will make the part stick more. A larger percent will make it stick less.
English:Distance
Translated:Distance
English:Gap Percent
Translated:Gap Percent
English:Try to connect mesh edges when the actual mesh data is not all the way connected.
Translated:Try to connect mesh edges when the actual mesh data is not all the way connected.
English:Sometime a mesh will not have closed a perimeters. When this is checked these non-closed perimeters while be closed.
Translated:Sometime a mesh will not have closed a perimeters. When this is checked these non-closed perimeters while be closed.
English:Reverse the orientation of overlaps. This can make some unintended holes go away.
Translated:Reverse the orientation of overlaps. This can make some unintended holes go away.
English:Make all overlap areas into one big area. This can make some unintended holes go away..
Translated:Make all overlap areas into one big area. This can make some unintended holes go away..
English:Repair
Translated:Repair
English:Connect Bad Edges
Translated:Connect Bad Edges
English:Close Polygons
Translated:Close Polygons
English:Reverse Orientation
Translated:Reverse Orientation
English:Merge All
Translated:Merge All
English:Overlaps
Translated:Overlaps
English:The distance between the first layer and the top of the raft. A good value is typically about 1/2 your extrusion diameter. So, between 0.0 and .2 for a .4 nozzle.
Translated:The distance between the first layer and the top of the raft. A good value is typically about 1/2 your extrusion diameter. So, between 0.0 and .2 for a .4 nozzle.
English:Air Gap
Translated:Air Gap
English:Outline Distance
Translated:Outline Distance
English:Distance Around Object
Translated:Distance Around Object
English:Minimum Travel\nRequiring Retraction
Translated:Minimum Travel\nRequiring Retraction
English:Show Printing
Translated:Show Printing
English:Show Current
Translated:Show Current
English:Printer Sync
Translated:Printer Sync
English:Sync To Print
Translated:Sync To Print
English:Layers
Translated:Layers
English:Show 3D
Translated:Show 3D
English:Uh-oh! Could not connect to printer.
Translated:Uh-oh! Could not connect to printer.
English:Installing
Translated:Installing
English:Initial Printer Setup
Translated:Initial Printer Setup
English:Homing The Printer
Translated:Homing The Printer
English:If in the future you need to re-calibrate your printer, or you wish to turn Auto Print Leveling off, you can find the print leveling controls in 'Advanced Settings'->'Configuration'.\n\nClick 'Done' to close this window.
Translated:If in the future you need to re-calibrate your printer, or you wish to turn Auto Print Leveling off, you can find the print leveling controls in 'Advanced Settings'->'Configuration'.\n\nClick 'Done' to close this window.
English:Print Leveling Overview
Translated:Print Leveling Overview
English:Note: Be sure the tip of the extrude is clean.
Translated:Note: Be sure the tip of the extrude is clean.
English:Title Stuff
Translated:Title Stuff
English:Oops! You cannot exit while a print is active.
Translated:Oops! You cannot exit while a print is active.
English:Unable to Exit
Translated:Unable to Exit
English:You are currently saving a parts sheet, are you sure you want to exit?
Translated:You are currently saving a parts sheet, are you sure you want to exit?
English:Confirm Exit
Translated:Confirm Exit
English:Disconnect and cancel the current print?
Translated:Disconnect and cancel the current print?
English:WARNING: Disconnecting will cancel the current print.\n\nDo you want to disconnect?
Translated:WARNING: Disconnecting will cancel the current print.\n\nDo you want to disconnect?
English:Note: Slice Settings are applied before the print actually starts. Changes while printing will not effect the active print.
Translated:Note: Slice Settings are applied before the print actually starts. Changes while printing will not effect the active print.
English:The extruder is currently heating and its target temperature cannot be changed until it reaches {0}°C.\n\nYou can set the starting extruder temperature in 'Slice Settings' -> 'Filament'.\n\n{1}
Translated:The extruder is currently heating and its target temperature cannot be changed until it reaches {0}°C.\n\nYou can set the starting extruder temperature in 'Slice Settings' -> 'Filament'.\n\n{1}
English:Waiting For Extruder To Heat
Translated:Waiting For Extruder To Heat
English:The bed is currently heating and its target temperature cannot be changed until it reaches {0}°C.\n\nYou can set the starting bed temperature in 'Slice Settings' -> 'Filament'.\n\n{1}
Translated:The bed is currently heating and its target temperature cannot be changed until it reaches {0}°C.\n\nYou can set the starting bed temperature in 'Slice Settings' -> 'Filament'.\n\n{1}
English:Waiting For Bed To Heat
Translated:Waiting For Bed To Heat
English:Cancel the current print?
Translated:Cancel the current print?
English:Cancel Print?
Translated:Cancel Print?
English:There is a recommended update avalible for MatterControl. Would you like to download it now?
Translated:There is a recommended update avalible for MatterControl. Would you like to download it now?
English:Recommended Update Available
Translated:Recommended Update Available
English:Download Now
Translated:Download Now
English:Remind Me Later
Translated:Remind Me Later
English:Oops! There is no eeprom mapping for your printer's firmware.
Translated:Oops! There is no eeprom mapping for your printer's firmware.
English:The term 'Baud Rate' roughly means the speed at which\ndata is transmitted. Baud rates may differ from printer to\nprinter. Refer to your printer manual for more info.\n\nTip: If you are uncertain - try 250000.
Translated:The term 'Baud Rate' roughly means the speed at which\ndata is transmitted. Baud rates may differ from printer to\nprinter. Refer to your printer manual for more info.\n\nTip: If you are uncertain - try 250000.
English:This is the minimum amount of filament that must be extruded before a retraction can occur.
Translated:This is the minimum amount of filament that must be extruded before a retraction can occur.
English:Support Options
Translated:Support Options
English:If this is checked support will be allowed starting on top of internal surfaces. If it is not checked support will only be created starting at the bed.
Translated:If this is checked support will be allowed starting on top of internal surfaces. If it is not checked support will only be created starting at the bed.
English:Support Everywhere
Translated:Support Everywhere
English:The angle the support infill will be drawn.
Translated:The angle the support infill will be drawn.
English:Infill Angle
Translated:Infill Angle
English:Grid
Translated:Grid
English:Moves
Translated:Moves
English:Retractions
Translated:Retractions
English:Speeds
Translated:Speeds
English:Extrusion
Translated:Extrusion
English:Special thanks to Alessandro Ranellucci for his incredible work on
Translated:Special thanks to Alessandro Ranellucci for his incredible work on
English:Dilimleme Motoru
Translated:Dilimleme Motoru
English:Clear
Translated:Clear
English:Lets the bed leveling code know if the printer can support the z axis going below 0. A printer with min z endstops or software end stops may not be able to.
Translated:Lets the bed leveling code know if the printer can support the z axis going below 0. A printer with min z endstops or software end stops may not be able to.
English:Z Can Be Negative
Translated:Z Can Be Negative
English:Export as X3G
Translated:Export as X3G
English:Select an Image
Translated:Select an Image
English:If greater than 0, this is the X by Y size of a tower to use to when changing extruders
Translated:If greater than 0, this is the X by Y size of a tower to use to when changing extruders
English:Extruder Change
Translated:Extruder Change
English:Wipe Tower Size
Translated:Wipe Tower Size
English:Sorry, we were unable to install the driver.
Translated:Sorry, we were unable to install the driver.
English:Tuning Adjustment
Translated:Tuning Adjustment
English:Release
Translated:Release
English:No printer is currently selected. Select a printer to edit slice settings.
Translated:No printer is currently selected. Select a printer to edit slice settings.
English:Part Preview
Translated:Part Preview
English:Layer Preview
Translated:Layer Preview
English:Enable Cloud Monitoring (disabled)
Translated:Enable Cloud Monitoring (disabled)
English:Warning - Moving Too Low
Translated:Warning - Moving Too Low
English:Oops! Could not find this file:
Translated:Oops! Could not find this file:
English:The number of extruders this machine has.
Translated:The number of extruders this machine has.
English:All extrusions are multiplied by this value. Increasing it above 1 (1.1 is a good max value) will increase the amount of filament being extruded; decreasing it (.9 is a good minimum value) will decrease the amount being extruded.
Translated:All extrusions are multiplied by this value. Increasing it above 1 (1.1 is a good max value) will increase the amount of filament being extruded; decreasing it (.9 is a good minimum value) will decrease the amount being extruded.
English:This is the minimum speed that the printer will reduce to to make the layer take long enough to satisfy the minimum layer time.
Translated:This is the minimum speed that the printer will reduce to to make the layer take long enough to satisfy the minimum layer time.
English:You can specify the extrusion with or set this to a % of the main extrusion widthe. Leave this as 0 to allow automatic calculation.
Translated:You can specify the extrusion with or set this to a % of the main extrusion widthe. Leave this as 0 to allow automatic calculation.
English:Material 3
Translated:Material 3
English:Material 4
Translated:Material 4
English:Material 5
Translated:Material 5
English:Unknown Reason
Translated:Unknown Reason
English:Port already in use
Translated:Port already in use
English:Unsupported Baud Rate
Translated:Unsupported Baud Rate
English:Port not found
Translated:Port not found
English:Cancelled
Translated:Cancelled
English:You can only connect when not currently connected.
Translated:You can only connect when not currently connected.
English:Warning - No EEProm Mapping
Translated:Warning - No EEProm Mapping
English:The speed to run the fan during the printing of the raft, 0 will leave the fan off.
Translated:The speed to run the fan during the printing of the raft, 0 will leave the fan off.
English:The speed to print the layers of the raft (other than the first layer). This can be set explicitly or as a percentage of the Infill speed.
Translated:The speed to print the layers of the raft (other than the first layer). This can be set explicitly or as a percentage of the Infill speed.
English:Preparing Meshes
Translated:Preparing Meshes
English:Grouping Meshes
Translated:Grouping Meshes
English:No COM ports available
Translated:No COM ports available
English:Stable
Translated:Stable
English:Beta
Translated:Beta
English:Alpha
Translated:Alpha
English:Ungrouping
Translated:Ungrouping
English:Grouping
Translated:Grouping
English:WARNING: Disconnecting will cancel the print.
Translated:WARNING: Disconnecting will cancel the print.
English:The amount the infill edge will push into the perimeter. Helps ensure the infill is connected to the edge.
Translated:The amount the infill edge will push into the perimeter. Helps ensure the infill is connected to the edge.
English:This is the diameter of your extruder nozzle.
Translated:This is the diameter of your extruder nozzle.
English:Sometime a mesh will not have closed a perimeter. When this is checked these non-closed perimeters while be closed.
Translated:Sometime a mesh will not have closed a perimeter. When this is checked these non-closed perimeters while be closed.
English:You can specify the extrusion with or set this to a % of the main extrusion width. Leave this as 0 to allow automatic calculation.
Translated:You can specify the extrusion with or set this to a % of the main extrusion width. Leave this as 0 to allow automatic calculation.
English:The default temperature to set the extruder to. Can sometimes be overridden on the first layer.
Translated:The default temperature to set the extruder to. Can sometimes be overridden on the first layer.
English:If greater than 0, this is the distance away from parts to create a perimeter to wipe when entering.
Translated:If greater than 0, this is the distance away from parts to create a perimeter to wipe when entering.
English:Please Confirm
Translated:Please Confirm
English:Reset to Factory Defaults
Translated:Reset to Factory Defaults
English:Save to EEProm
Translated:Save to EEProm
English:{0} is not available
Translated:{0} is not available
English:Invalid printer response
Translated:Invalid printer response
English:Could not find a selected button.
Translated:Could not find a selected button.
English:Aligning
Translated:Aligning
English:Single
Translated:Single
English:Warning - GCode file
Translated:Warning - GCode file
English:The index of the extruder to use for the raft. Setting this to 0 will use the support extruder index.
Translated:The index of the extruder to use for the raft. Setting this to 0 will use the support extruder index.
English:Raft Extruder
Translated:Raft Extruder
English:None
Translated:None
English:Rectangle
Translated:Rectangle
English:Outline
Translated:Outline
English:Circle
Translated:Circle
English:The file you are attempting to print is a GCode file.\n\nGCode files tell your printer exactly what to do. They are not modified by SliceSettings and may not be appropriate for your specific printer configuration.\n\nOnly print from GCode files if you know they mach your current printer and configuration.\n\nAre you sure you want to print this GCode file?
Translated:The file you are attempting to print is a GCode file.\n\nGCode files tell your printer exactly what to do. They are not modified by SliceSettings and may not be appropriate for your specific printer configuration.\n\nOnly print from GCode files if you know they mach your current printer and configuration.\n\nAre you sure you want to print this GCode file?
English:Do not show this message again
Translated:Do not show this message again
English:The file you are attempting to print is a GCode file.\n\nIt is recommendended that you only print Gcode files known to match your printer's configuration.\n\nAre you sure you want to print this GCode file?
Translated:The file you are attempting to print is a GCode file.\n\nIt is recommendended that you only print Gcode files known to match your printer's configuration.\n\nAre you sure you want to print this GCode file?
English:Cannot find this file\nWould you like to remove it from the queue?
Translated:Cannot find this file\nWould you like to remove it from the queue?
English:Normally while printing the printer will home before heating the extruder(s). Set this to cause the heating to happen before the homing. This can help with printers that touch the bed while homing.
Translated:Normally while printing the printer will home before heating the extruder(s). Set this to cause the heating to happen before the homing. This can help with printers that touch the bed while homing.
English:Heat Before Homing
Translated:Heat Before Homing
English:Clear Print History
Translated:Clear Print History
English:This gcode will be inserted into the output right after the temperature setting. If you have the commands to set temperature in this section they will not be generated outside of this section. You can also include values from other settings such as [temperature].
Translated:This gcode will be inserted into the output right after the temperature setting. If you have the commands to set temperature in this section they will not be generated outside of this section. You can also include values from other settings such as [temperature].
English:GCode file too big to load for '{0}'.
Translated:GCode file too big to load for '{0}'.
English:Reset\nConnection
Translated:Reset\nConnection
English:Show Reset Connection
Translated:Show Reset Connection
English:Makes visible a button that will reset the connection when pressed. This can be used on printers that support it as an emergency stop.
Translated:Makes visible a button that will reset the connection when pressed. This can be used on printers that support it as an emergency stop.
English:You may need to wait a minute for your printer to finish initializing.
Translated:You may need to wait a minute for your printer to finish initializing.
English:How many layers, or the distance, that will be solid filled on the bottom surfaces of the object. Add mm to the end of the number to specify distance.
Translated:How many layers, or the distance, that will be solid filled on the bottom surfaces of the object. Add mm to the end of the number to specify distance.
English:The number of layers, or the distance, to print between the supports and the part. Add mm to the end of the number to specify distance.
Translated:The number of layers, or the distance, to print between the supports and the part. Add mm to the end of the number to specify distance.
English:The number of layers, or the distance, to skip between the support and the model. Add mm to the end of the number to specify distance.
Translated:The number of layers, or the distance, to skip between the support and the model. Add mm to the end of the number to specify distance.
English:How many layers, or the distance, that will be solid filled on the top surfaces of the object. Add mm to the end of the number to specify distance.
Translated:How many layers, or the distance, that will be solid filled on the top surfaces of the object. Add mm to the end of the number to specify distance.
English:Top Solid Layers:
Translated:Top Solid Layers:
English:Bottom Solid Layers:
Translated:Bottom Solid Layers:
English:This will cause the extruder to try to wipe itself after retracting to minimize strings.
Translated:This will cause the extruder to try to wipe itself after retracting to minimize strings.
English:Calculating Positions...
Translated:Calculating Positions...
English:ATX Power Control
Translated:ATX Power Control
English:Specify if your printer can control the power supply
Translated:Specify if your printer can control the power supply
English:Has Power Control
Translated:Has Power Control
English:The temperature the bed temperature will be set to when part is to be removed.
Translated:The temperature the bed temperature will be set to when part is to be removed.
English:Extruder Wipe Temperature
Translated:Extruder Wipe Temperature
English:Bed Remove Part Temperature
Translated:Bed Remove Part Temperature
English::The temperature the extruder will be when extruder wipes.
Translated::The temperature the extruder will be when extruder wipes.
English:The temperature the extruder will be when extruder wipes.
Translated:The temperature the extruder will be when extruder wipes.
English:Basic
Translated:Basic
English:Sets the size of the outer solid surface for the entire print.
Translated:Sets the size of the outer solid surface for the entire print.
English:The number, or total width, of external shells to create. Add mm to the end of the number to specify width.
Translated:The number, or total width, of external shells to create. Add mm to the end of the number to specify width.
English:Layers/Surface
Translated:Layers/Surface
English:Width
Translated:Width
English:Arrange
Translated:Arrange
English:The speed to move while printing the first layer. If expressed as a percentage it will modify the corresponding speed set above.
Translated:The speed to move while printing the first layer. If expressed as a percentage it will modify the corresponding speed set above.
English:This gcode will sent to the printer immediately after connecting. It can be used to set settings specific to a given printer.
Translated:This gcode will sent to the printer immediately after connecting. It can be used to set settings specific to a given printer.
English:The collection you are trying to delete '{0}' is not empty. Would you like to delete it anyway?
Translated:The collection you are trying to delete '{0}' is not empty. Would you like to delete it anyway?
English:Collection not Empty
Translated:Collection not Empty
English:Do NOT Delete
Translated:Do NOT Delete
English:Library (cloud)
Translated:Library (cloud)
English:Purchased
Translated:Purchased
English:Session Expired
Translated:Session Expired
English:Thumbnail Rendering
Translated:Thumbnail Rendering
English:Flat
Translated:Flat
English:3D
Translated:3D
English:Update Status
Translated:Update Status
English:The folder you are trying to delete '{0}' is not empty. Would you like to delete it anyway?
Translated:The folder you are trying to delete '{0}' is not empty. Would you like to delete it anyway?
English:Folder not Empty
Translated:Folder not Empty
English:The folder '{0}' is not empty.\nWould you like to delete it anyway?
Translated:The folder '{0}' is not empty.\nWould you like to delete it anyway?
English:Delete folder?
Translated:Delete folder?
English:The folder '{0}' is not empty.\n\nWould you like to delete it anyway?
Translated:The folder '{0}' is not empty.\n\nWould you like to delete it anyway?
English:Cloud Library
Translated:Cloud Library
English:Rename
Translated:Rename
English:Rename Item:
Translated:Rename Item:
English:New Name
Translated:New Name
English:Enter New Name Here
Translated:Enter New Name Here
English:The speed to print the visible outside edges. This can be set explicitly or as a percentage of the Inside Perimeters speed.
Translated:The speed to print the visible outside edges. This can be set explicitly or as a percentage of the Inside Perimeters speed.
English:Save New Design
Translated:Save New Design
English:Save Location
Translated:Save Location
English:Choose the location to save to.
Translated:Choose the location to save to.
English:Sample the bed at seven points
Translated:Sample the bed at seven points
English:You should be done in about 5 minutes.
Translated:You should be done in about 5 minutes.
English:The print leveling alogrithm to use.
Translated:The print leveling alogrithm to use.
English:The print leveling sampling mothod to use.
Translated:The print leveling sampling mothod to use.
English:This gcode will be run prior to starting bed probing.
Translated:This gcode will be run prior to starting bed probing.
English:This gcode will be run after finishing bed probing.
Translated:This gcode will be run after finishing bed probing.
English:The width of the paper (or other calibration device) used when doing manual bed probing.
Translated:The width of the paper (or other calibration device) used when doing manual bed probing.
English:The offset of the probe relative to the extruder.
Translated:The offset of the probe relative to the extruder.
English:The z offset of the probe relative to the extruder.
Translated:The z offset of the probe relative to the extruder.
English:Print Leveling
Translated:Print Leveling
English:Leveling Solution
Translated:Leveling Solution
English:Leveling Method
Translated:Leveling Method
English:Manual Probe Paper Width
Translated:Manual Probe Paper Width
English:Probe Offset
Translated:Probe Offset
English:Probe Z Offset
Translated:Probe Z Offset
English:There is a recommended update available for MatterControl. Would you like to download it now?
Translated:There is a recommended update available for MatterControl. Would you like to download it now?
English:The file you are attempting to print is a GCode file.\n\nIt is recommended that you only print Gcode files known to match your printer's configuration.\n\nAre you sure you want to print this GCode file?
Translated:The file you are attempting to print is a GCode file.\n\nIt is recommended that you only print Gcode files known to match your printer's configuration.\n\nAre you sure you want to print this GCode file?
English:This printer requires print leveling to run correctly.
Translated:This printer requires print leveling to run correctly.
English:Require Leveling To Print
Translated:Require Leveling To Print
English:Oops! You cannot restart while a print is active.
Translated:Oops! You cannot restart while a print is active.
English:Unable to restart
Translated:Unable to restart
English:Add File To Queue
Translated:Add File To Queue
English:Add Folder To Library
Translated:Add Folder To Library
English:Using the above controls
Translated:Using the above controls
English:Add Local Folder To Library
Translated:Add Local Folder To Library
English:Redeem Design Code
Translated:Redeem Design Code
English:You should be done in about 6 minutes.
Translated:You should be done in about 6 minutes.
English:Enter Share Code
Translated:Enter Share Code
English:Downloading...
Translated:Downloading...
English:Uploading...
Translated:Uploading...
English:Click to show in 3D View
Translated:Click to show in 3D View
English:Enter Mulit Select mode
Translated:Enter Mulit Select mode
English:Add a .stl, .amf, .gcode or .zip File To The Queue
Translated:Add a .stl, .amf, .gcode or .zip File To The Queue
English:Choose a Create Tool to generate custom parts
Translated:Choose a Create Tool to generate custom parts
English:Switch to Setings and Manual Controls pannel
Translated:Switch to Setings and Manual Controls pannel
English:Pop This Tab out into its own Window
Translated:Pop This Tab out into its own Window
English:Preview layer Tool Paths
Translated:Preview layer Tool Paths
English:Add a .stl, .amf, .gcode or .zip File to the Queue
Translated:Add a .stl, .amf, .gcode or .zip File to the Queue
English:Add a .stl, .amf, .gcode or .zip File to the Bed
Translated:Add a .stl, .amf, .gcode or .zip File to the Bed
English:Add an .stl, .amf, .gcode or .zip file to the Queue
Translated:Add an .stl, .amf, .gcode or .zip file to the Queue
English:Insert an .stl, .amf, .gcode or .zip file
Translated:Insert an .stl, .amf, .gcode or .zip file
English:Bring the Window back into this Tab
Translated:Bring the Window back into this Tab
English:Insert an .stl, .amf or .zip file
Translated:Insert an .stl, .amf or .zip file
English:Update Channel
Translated:Update Channel
English:Current Build : Test Build
Translated:Current Build : Test Build
English:Stable: The current release version of MatterControl (recommended).
Translated:Stable: The current release version of MatterControl (recommended).
English:Beta: The release candidate version of MatterControl.
Translated:Beta: The release candidate version of MatterControl.
English:Alpha: The in development version of MatterControl.
Translated:Alpha: The in development version of MatterControl.
English:Choose a Create Tool to generate custom designs
Translated:Choose a Create Tool to generate custom designs
English:Switch to Settings, Controls and Options
Translated:Switch to Settings, Controls and Options
English:Switch to Queue, Library and History
Translated:Switch to Queue, Library and History
English:Sign in to your MatterControl account
Translated:Sign in to your MatterControl account
English:Connect to the currently selected printer
Translated:Connect to the currently selected printer
English:Disconnect from current printer
Translated:Disconnect from current printer
English:Select a printer
Translated:Select a printer
English:Current extruder temperature
Translated:Current extruder temperature
English:Preheat the Extruder
Translated:Preheat the Extruder
English:Current bed temperature
Translated:Current bed temperature
English:Preheat the Bed
Translated:Preheat the Bed
English:Shop online for printing materials
Translated:Shop online for printing materials
English:Add an .stl, .amf, .gcode or .zip file to the Library
Translated:Add an .stl, .amf, .gcode or .zip file to the Library
