avoid_crossing_perimeters|Avoid Crossing Perimeters|CHECK_BOX||Attempts to minimize the number of perimeter crossing. This can help with oozing or strings.
bed_temperature|Bed Temperature|POSITIVE_DOUBLE|degrees|The default temperature to set the bed to. Can sometimes be overriden on the first layer. Set to 0 to eliminate bed temperature commands.
bridge_flow_ratio|Bridge Flow Ratio|POSITIVE_DOUBLE||This controls the ratio of material extruder during bridging. Reducing this slightly can help bridging by stretching the filament more, using a fan can also help greatly.
bridge_speed|Bridges|POSITIVE_DOUBLE|mm/s|The speed to move when bridging between walls.
brim_width|Brim Width|POSITIVE_DOUBLE|mm|The amount of brim that will be drawn around each object. This is useful to ensure that parts stay affixed to the bed.
build_height|Build Height|POSITIVE_DOUBLE|mm|The height of the printable area. If set to 0 the parts height will not be validated.
center_part_on_bed|Center On Bed|CHECK_BOX||This will cause the print to be centered on the bed. Disable this if you know your models have been created where you want them to print.
complete_objects|Complete Individual Objects|CHECK_BOX||Each individual part is printed to completion then the extruder is lowered back to the bed and the next part is printed.
raft_extra_distance_around_part|Distance Around Object|POSITIVE_DOUBLE|mm|The extra distance the raft will extend around the part.
raft_air_gap|Air Gap|POSITIVE_DOUBLE|mm|The distance between the first layer and the top of the raft. A good value is typically about 1/2 your extrusion diameter. So, between 0.0 and .2 for a .4 nozzle.
default_acceleration|Default|POSITIVE_DOUBLE|mm/s<>|Acceleration to use on all moves not defined above. Set to 0 to disable changing the printer's acceleration.
external_perimeter_speed|Outside Perimeter|DOUBLE_OR_PERCENT|mm/s or %|The speed to print the visible outside edges. This can be set explicitly or as a percentage of the Perimeters speed.
extruder_clearance_height|Extruder Clearance Height|POSITIVE_DOUBLE|mm|This is used to figure out how far apart individual parts must be printed to allow them to be completed before printing the next part.
extruder_clearance_radius|Extruder Clearance Radius|POSITIVE_DOUBLE|mm|This is used to figure out how far apart individual parts must be printed to allow them to be completed before printing the next part.
extruder_offset|Extruder Offset|OFFSET2|mm|This is the offset of each extruder relative to the first extruder. Only useful for multiple extruder machines.
extrusion_multiplier|Extrusion Multiplier|POSITIVE_DOUBLE||All extrusions are multiplied by this value. Increasing it above 1 (1.1 is a good max value) will increase the amount of filament being extruded; decreasing it (.9 is a good minimum value) will decrease the amount being extruded.
extrusion_width|Default Extrusion Width|DOUBLE_OR_PERCENT|mm or %\nleave 0 for auto|Leave this as 0 to allow automatic calculation of extrusion width.
fan_always_on|Keep Fan Always On|CHECK_BOX||This will force the fan to remain on throughout the print. In general you should have this off and just enable auto cooling.
fan_below_layer_time|Enable Fan If Layer\nPrint Time Is Below|INT|Seconds|If a layer is estimated to take less than this to print, the fan will be turned on.
filament_diameter|Diameter|POSITIVE_DOUBLE|mm|This should be set to the actual diameter of the filament you are using on your printer. Measure 5 times with calipers, throw out the top and bottom, and average the remaining 3.
fill_density|Fill Density|DOUBLE_OR_PERCENT|Ratio (0 to 1)|The ratio of material to empty space ranged 0 to 1. Zero would be no infill; 1 is solid infill.
fill_pattern|Fill Pattern|LIST|rectilinear,line,concentric,honeycomb,hilbertcurve,achimedeancords,octagramspiral|The pattern used on the inside portions of the print.
first_layer_acceleration|First Layer|DOUBLE|mm/s|Acceleration to use while printing the first layer. Set to 0 to the default first layer acceleration.
first_layer_bed_temperature|Bed First Layer|DOUBLE|degrees|The temperature to set the bed to before printing the first layer. The printer will wait until this temperature has been reached before printing. Set to 0 to eliminate bed temperature commands.
first_layer_extrusion_width|First Layer|DOUBLE_OR_PERCENT|mm or %\nleave 0 for default|Setting this to greater than 100% can often help the first layer have better adhesion to the print bed.
first_layer_height|First Layer Height|DOUBLE_OR_PERCENT|mm or %|Sets the height of the first layer. It is often desirable to print a taller first layer to ensure a good solid adhesion to the build plate.
first_layer_speed|First Layer Speed|DOUBLE_OR_PERCENT|mm/s or %|The speed to move while printing the first layer. If expressed as a percentage it will modify the corresponding speed set above.
first_layer_temperature|Extrude First Layer|POSITIVE_DOUBLE|degrees|The temperature to set the extruder to before printing the first layer of a part. The printer will wait until this temperature has been reached before printing.
gcode_arcs|Use Arcs|CHECK_BOX||Use firmware arcs rather than multiple segments for curves.
gcode_comments|Verbose G-Code|CHECK_BOX||Include detailed comments in the gcode.
gcode_flavor|G-Code Flavor|LIST|reprap,teacup,makerbot,sailfish,mach3_ecm,no_extrusion|Some firmware use different g and m codes. Setting this ensures that the output gcode will use the correct commands.
gcode_output_type|G-Code Output|LIST|REPRAP,ULTIGCODE,MAKERBOT,BFB,MACH3|Some firmware use different g and m codes. Setting this ensures that the output gcode will use the correct commands.
has_fan|Has Fan|HARDWARE_PRESENT|bridge_fan_speed,disable_fan_first_layers,fan_always_on,fan_below_layer_time,max_fan_speed,min_fan_speed|Specify if your printer has a fan.
has_heated_bed|Has Heated Bed|HARDWARE_PRESENT||Specify if your printer has a heated bed.
has_sd_card_reader|Has SD Card Reader|HARDWARE_PRESENT|bed_temperature,first_layer_bed_temperature|Specify if your printer has the ability to plug in an SD card.
infill_overlap_perimeter|Infill Overlap|POSITIVE_DOUBLE|mm|The amount the infill edge will push into the preimiter. Helps ensure the infill is connected to the edge.
infill_speed|Infill|POSITIVE_DOUBLE|mm/s|The speed to print infill.
layer_height|Layer Height|POSITIVE_DOUBLE|mm|Sets the height of each layer of the print. A smaller number will create more layers and more vertical accuracy but also a slower print.
min_extrusion_before_retract|Minimum Extrusion\nRequiring Retraction|POSITIVE_DOUBLE|mm|This is the minimum amount of filament that must be extruded before a retraction can occur.
min_fan_speed|Minimum Fan Speed|INT|%|This is the minimum fan speed that your fan can run at.
min_print_speed|Minimum Print Speed|POSITIVE_DOUBLE|mm/s|This is the minimum speed that the printer will reduce to to make the layer take long enough to satisfy the minimum layer time.
min_skirt_length|Minimum Extrusion Length|POSITIVE_DOUBLE|mm|Sets the minimum amount of filament to use drawing the skirt loops. This will cause at least enough skirt loops to be drawn to use this amount of filament.
perimeters|Perimeters (minimum)|INT||The number of external layers or shells to create.
post_process|Post-Processing Scripts|MULTI_LINE_TEXT||You can include additional programs to process the gcode after slicer is finished. The complete path of the program to run should be included here.
print_center|Print Center|VECTOR2|mm|The position (coordinates) of the center of the print bed.
raft_layers|Raft Layers|INT|layers|Number of layers to print before printing any parts.
randomize_start|Randomize Starting Points|CHECK_BOX||Start each new layer from a different vertex to reduce seams.
retract_before_travel|Minimum Travel\nRequiring Retraction|POSITIVE_DOUBLE|mm|The minimum distance of a non-printing move that will result in a retraction.
retract_lift|Z Lift|POSITIVE_DOUBLE|mm|The amount the extruder head will be lifted after each retraction.
retract_restart_extra_toolchange|Length|POSITIVE_DOUBLE|mm\nzero to disable|The amount the filament will be retracted when changing to a different extruder.
repair_outlines_extensive_stitching|Connect Bad Edges|CHECK_BOX||Try to connect mesh edges when the actual mesh data is not all the way connected.
repair_outlines_keep_open|Close Polygons|CHECK_BOX||Sometime a mesh will not have closed a perimeters. When this is checked these non-closed perimeters while be closed.
repair_overlaps_reverse_orientation|Reverse Orientation|CHECK_BOX||Reverse the orientation of overlaps. This can make some unintended holes go away.
repair_overlaps_union_all_together|Merge All|CHECK_BOX||Make all overlap areas into one big area. This can make some unintended holes go away..
resolution|Resolution|POSITIVE_DOUBLE|mm|The minimum feature size to consider from the model. Leave at 0 to use all the model detail.
skirt_distance|Distance from Object|POSITIVE_DOUBLE|mm|The distance to start drawing the first skirt loop. Make this 0 to create an anchor for the part to the bed.
skirt_height|Skirt Height|INT|layers|The number of layers to draw the skirt.
skirts|Loops|INT||The number of loops to draw around all the parts on the bed.
slowdown_below_layer_time|Slow Down If Layer Print\nTime Is Below|INT|Seconds|If a layer is estimated to take less than this to print, the movement speed will be reduced to try and make the layer take this long to print.
small_perimeter_speed|Small Perimeters|DOUBLE_OR_PERCENT|mm/s or %|Used for small perimeters (usually holes). This can be set explicitly or as a percentage of the Perimeters' speed.
solid_fill_pattern|Top/Bottom Fill Pattern|LIST|rectilinear,concentric,hilbertcurve,achimedeancords,octagramspiral|The pattern used on the bottom and top layers of the print.
solid_infill_every_layers|Solid Infill Every|INT|layers|Sets how often a layer will be forced to be solid infilled. Zero will result in normal infill throughout.
solid_infill_extrusion_width|Solid Infill|DOUBLE_OR_PERCENT|mm or %\nleave 0 for default|Leave this as 0 to allow automatic calculation of extrusion width.
solid_infill_speed|Solid Infill|DOUBLE_OR_PERCENT|mm/s|The speed to print infill when completely solid. This can be set explicitly or as a percentage of the Infill speed.
spiral_vase|Spiral Vase|CHECK_BOX||Force the print to have only one layer and gradually increase the extruder height during the print. Only one part can be printed at a time with this feature.
standby_temperature_delta|Temp Lower Amount|DOUBLE|degrees|This is the amount to lower the temperature of an extruder that is not currently printing.
start_gcode|Start G-Code|MULTI_LINE_TEXT||This gcode will be inserted into the output right after the temperature setting. If you have the commands to set temperature in this section they will not be generated outside of this section. You can also include values from other settings such as [first_layer_temperature].
start_perimeters_at_concave_points|Start At Concave Points|CHECK_BOX||Make sure the first point on a perimeter is a concave point.
start_perimeters_at_non_overhang|Start At Non Overhang|CHECK_BOX||Make sure the first point on a perimeter is not an overhang.
support_material_infill_angle|Infill Angle|POSITIVE_DOUBLE|degrees|The angle the support infill will be drawn.
support_material_create_internal_support|Support Everywhere|CHECK_BOX||If this is checked support will be allowed starting on top of internal surfaces. If it is not checked support will only be created starting at the bed.
support_material_enforce_layers|Enforce Support For First|INT|layers|Generate support material everywhere not touching the bed for n layers, regardless of angle.
support_material_extruder|Support Material Extruder|INT||The index of the extruder to use for support material.
support_material_extrusion_width|Support Material|DOUBLE_OR_PERCENT|mm or %\nleave 0 for default|Leave this as 0 to allow automatic calculation of extrusion width.
support_material_interface_extruder|Support Interface Extruder|INT||The index of the extruder to use for support material interface layers.
support_material_interface_layers|Interface Layers|INT|layers|The number of layers to print between the supports and the part.
support_material_threshold|Overhang Threshold|POSITIVE_DOUBLE|degrees|The last angle at which support material will be generated. Larger numbers will result in more support.
temperature|Extruder Temperature|POSITIVE_DOUBLE|degrees|The default temperature to set the extruder to. Can sometimes be overriden on the first layer.
thin_walls|Thin Walls|CHECK_BOX||Detect when walls are too close together and need to be extruded as just one wall.
threads|Threads|INT||The number of CPU cores to use while doing slicing. Increasing this can slow down your machine.
toolchange_gcode|Tool Change G-Code|MULTI_LINE_TEXT||This gcode will be inserted after every tool change.
top_infill_extrusion_width|Top Solid Infill|DOUBLE_OR_PERCENT|mm or %\nleave 0 for default|Leave this as 0 to allow automatic calculation of extrusion width.
top_solid_infill_speed|Top Solid Infill|DOUBLE_OR_PERCENT|mm/s|The speed to print the top infill. This can be set explicitly or as a percentage of the Infill speed.
use_firmware_retraction|Use Firmware Retraction|CHECK_BOX||Request the firmware to do retractions rather than specify the extruder movements directly.
use_relative_e_distances|Use Relative E Distances|CHECK_BOX||Normally you will want to use absolute e distances. Only check this if you know your printer needs relative e distances.
vibration_limit|Vibration Limit|INT|Hz|This is to help reduce vibrations during printing. If your printer has a resonance frequency that is causing trouble you can set this to try and reduce printing at that frequency.
wipe|Wipe Before Retract|CHECK_BOX||This will cause the extruder to move while retracting to minimize blobs.
wipe_shield_distance|Wipe Shield Distance|POSITIVE_DOUBLE|mm|If greater than 0, this is the distance away from parts to create a parimeter to wipe when entering.
z_can_be_negative|Z Can Be Negative|CHECK_BOX||Lets the bed leveling code know if the printer can support the z axis going below 0. A printer with min z endstops or software end stops may not be able to.
