2016-07-19 13:01:20 -07:00
{
"DocumentVersion": 201606271,
"ID": null,
"Macros": [],
"OemLayer": {
"avoid_crossing_perimeters": "1",
"bed_remove_part_temperature": "0",
"bed_shape": "rectangular",
"bed_size": "410,410",
"bed_temperature": "0",
"bottom_clip_amount": "0",
"bridge_acceleration": "0",
"bridge_fan_speed": "100",
"bridge_flow_ratio": "1",
"bridge_speed": "20",
"brim_width": "0",
"build_height": "533",
"cancel_gcode": "",
"center_part_on_bed": "1",
"complete_objects": "0",
"connect_gcode": "",
"cool_extruder_lift": "0",
"cooling": "1",
"create_raft": "0",
"default_acceleration": "0",
"disable_fan_first_layers": "1",
"end_gcode": "M104 S0 ; turn off temperature\\nG28 X0 ; home X axis\\nM84 ; disable motors",
"external_perimeter_speed": "70%",
"external_perimeters_first": "0",
"extra_perimeters": "1",
"extruder_clearance_height": "20",
"extruder_clearance_radius": "20",
"extruder_count": "1",
"extruder_offset": "0x0,0x0,0x0,0x0",
"extruder_wipe_temperature": "0",
"extruders_share_temperature": "0",
"extrusion_axis": "E",
"extrusion_multiplier": "1",
"extrusion_width": "0",
"fan_always_on": "0",
"fan_below_layer_time": "60",
"filament_diameter": "1.75",
"fill_angle": "45",
"fill_density": "0.4",
"fill_pattern": "honeycomb",
"first_layer_acceleration": "0",
"first_layer_bed_temperature": "75",
"first_layer_height": "0.3",
"first_layer_speed": "30%",
"first_layer_temperature": "205",
"g0": "0",
"gap_fill_speed": "20",
"gcode_arcs": "0",
"gcode_comments": "0",
"gcode_flavor": "reprap",
"gcode_output_type": "REPRAP",
"has_fan": "1",
"has_hardware_leveling": "0",
"has_heated_bed": "0",
"has_power_control": "0",
"has_sd_card_reader": "1",
"heat_extruder_before_homing": "0",
"infill_acceleration": "0",
"infill_every_layers": "1",
"infill_extruder": "1",
"infill_extrusion_width": "0",
"infill_first": "0",
"infill_only_where_needed": "0",
"infill_overlap_perimeter": ".06",
"infill_speed": "60",
"infill_type": "TRIANGLES",
"layer_height": "0.2",
"max_fan_speed": "100",
"min_extrusion_before_retract": ".1",
"min_fan_speed": "35",
"min_print_speed": "10",
"min_skirt_length": "0",
"notes": "",
"nozzle_diameter": "0.5",
"only_retract_when_crossing_perimeters": "1",
"ooze_prevention": "0",
"output_filename_format": "[input_filename_base].gcode",
"overhangs": "1",
"pause_gcode": "",
"perimeter_acceleration": "0",
"perimeter_extruder": "1",
"perimeter_extrusion_width": "0",
"perimeter_speed": "30",
"perimeters": "3",
"post_process": "",
"print_center": "205,205",
"raft_air_gap": ".2",
"raft_extra_distance_around_part": "5",
"raft_extruder": "0",
"raft_fan_speed_percent": "100",
"raft_layers": "0",
"raft_print_speed": "100%",
"randomize_start": "0",
"repair_outlines_extensive_stitching": "0",
"repair_outlines_keep_open": "0",
"resolution": "0",
"resume_gcode": "",
"retract_before_travel": "20",
"retract_layer_change": "1",
"retract_length": "1",
"retract_length_tool_change": "10",
"retract_lift": "0",
"retract_restart_extra": "0",
"retract_restart_extra_toolchange": "0",
"retract_speed": "30",
"show_reset_connection": "1",
"skirt_distance": "6",
"skirt_height": "1",
"skirts": "1",
"slowdown_below_layer_time": "30",
"small_perimeter_speed": "30",
"solid_fill_pattern": "rectilinear",
"solid_infill_below_area": "70",
"solid_infill_every_layers": "0",
"solid_infill_extrusion_width": "0",
"solid_infill_speed": "60",
"solid_shell": "0",
"spiral_vase": "0",
"standby_temperature_delta": "-5",
"start_gcode": "G28 ; home all axes\\nM218 T1 X45.2 Y0.15; Set 2nd extruder offset. This method is better than setting in in the extruder tab since it can be updated easily later\\nM201 X600 Y600; Set X and Y acceleration values\\nM204 S600; Set default acceleration\\nG1 Z5 F5000; Raise nozzle",
"start_perimeters_at_concave_points": "0",
"start_perimeters_at_non_overhang": "0",
"support_material": "0",
"support_material_angle": "45",
"support_material_enforce_layers": "0",
"support_material_extruder": "1",
"support_material_extrusion_width": "0",
"support_material_infill_angle": "45",
"support_material_interface_extruder": "1",
"support_material_interface_layers": ".9mm",
"support_material_interface_spacing": "0",
"support_material_pattern": "honeycomb",
"support_material_spacing": "2.5",
"support_material_speed": "60",
"support_material_threshold": "0",
"support_material_xy_distance": "0.7",
"support_material_z_distance": "0.15",
"support_material_z_gap_layers": ".3mm",
"support_type": "LINES",
"temperature": "200",
"thin_walls": "1",
"threads": "2",
"toolchange_gcode": "",
"top_infill_extrusion_width": "0",
"top_solid_infill_speed": "50",
"top_solid_layers": "1mm",
"travel_speed": "130",
"use_firmware_retraction": "0",
"use_relative_e_distances": "0",
"vibration_limit": "0",
"wipe": "0",
"wipe_shield_distance": "0",
"wipe_tower_size": "0",
"z_can_be_negative": "0",
"z_offset": "0",
"make": "gCreate",
"model": "gMax",
"created_date": "7/19/2016 7:54:54 PM",
"baud_rate": "250000",
"default_material_presets": "PLA",
"windows_driver": "MHSerial.inf",
"calibration_files": "Calibration - Circle.stl"
},
"ActiveQualityKey": "",
"MaterialSettingsKeys": [],
"UserLayer": {},
"MaterialLayers": [
{
"layer_name": "ABS",
2016-07-25 14:18:56 -07:00
"filament_density": "1.04",
2016-07-19 13:01:20 -07:00
"layer_id": "3985bf74-6a09-42dc-99c9-ab2488683efe",
"disable_fan_first_layers": "2",
"max_fan_speed": "35",
"min_fan_speed": "25",
"temperature": "235"
},
{
"layer_name": "PLA",
2016-07-25 14:18:56 -07:00
"filament_density": "1.24",
2016-07-19 13:01:20 -07:00
"layer_id": "8d02a971-6552-46cc-aee4-e3dd665a9251",
"disable_fan_first_layers": "2",
"max_fan_speed": "75",
"min_fan_speed": "55",
"temperature": "201"
}
],
"QualityLayers": [
{
"layer_name": "High",
"layer_id": "e160d49b-0e2c-474c-94c0-25e58a11af75",
2016-07-20 15:38:38 -07:00
"bottom_solid_layers": "1mm",
2016-07-19 13:01:20 -07:00
"external_perimeter_speed": "60%",
"infill_speed": "70",
"layer_height": "0.16",
"max_fan_speed": "85",
"min_fan_speed": "65",
"perimeter_speed": "65",
"top_solid_layers": "5",
"travel_speed": "120"
},
{
"layer_name": "Low (Quick Print)",
"layer_id": "7dddeb5a-0bfe-499b-8911-30de40faa881",
2016-07-20 15:38:38 -07:00
"bottom_solid_layers": "1mm",
2016-07-19 13:01:20 -07:00
"external_perimeter_speed": "60%",
"infill_speed": "70",
"layer_height": "0.3",
"max_fan_speed": "85",
"min_fan_speed": "65",
"perimeter_speed": "70",
"top_solid_layers": "2",
"travel_speed": "130"
},
{
"layer_name": "Medium (Complex Model)",
"layer_id": "9bac03e6-56a4-4d6d-912f-fa09a46db848",
"external_perimeter_speed": "45%",
"infill_speed": "70",
"layer_height": "0.24",
"max_fan_speed": "85",
"min_fan_speed": "70",
"perimeter_speed": "60",
"travel_speed": "120"
},
{
"layer_name": "Medium (Simple Model)",
"layer_id": "b9fa9acc-e1a5-4171-9059-e230eaf6ec2d",
2016-07-20 15:38:38 -07:00
"bottom_solid_layers": "1mm",
2016-07-19 13:01:20 -07:00
"external_perimeter_speed": "75%",
"infill_speed": "70",
"layer_height": "0.24",
"max_fan_speed": "85",
"min_fan_speed": "65",
"perimeter_speed": "70",
"top_solid_layers": "3",
"travel_speed": "120"
}
]
}
